SAE AS 81936 1A-2006 BEARING PLAIN SELF-ALIGNING CU-BE BALL CRES RACE (WITH GROOVED RACE) -65 TO +350 《CRES轴承圈、CU滚珠、自调、滑动轴承-65到+350华氏度（凹槽轴承圈）》.pdf

1、 AEROSPACE STANDARD BEARING, PLAIN, SELF-ALIGNING, CU-BE BALL, CRES RACE, (WITH GROOVED RACE) -65 F TO +350 F AS81936/1 Copyright 2006 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect

2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-05REVISED

3、 2006-03 THIRD ANGLE PROJECTION CUSTODIAN: SAE ACBG REV. A FEDERAL SUPPLY CLASS3120 AS81936/1 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences.The use of thisreport

4、 is entirely voluntary, andits applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelled.SAE invites y

5、ourwritten commentsandsuggestions.RATIONALE THIS DOCUMENT HAS BEEN REVISED TO UPDATE REFERENCES TO CURRENT SPECIFICATIONS AND STANDARDS; TO REFLECT ACBG POLICY REGARDING HEAT TREATMENT SPECIFICATION CALLOUTS; TO CORRECT TABLE 1 DIMENSIONS L, N, AND R TO REFER TO BALL ID GROOVES; AND TO CORRECT TABLE

6、 2 COLUMN LABEL TO REFER TO AXIAL STATIC LIMIT LOAD. THE REQUIREMENTS FOR ACQUIRING THE PRODUCT(S) DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE ISSUE OF THE FOLLOWING SPECIFICATION LISTED IN THAT ISSUE OF THE DODISS SPECIFIED IN THE SOLICITATION: AS81936. FIGURE 1 AEROSPACE STA

7、NDARD BEARING, PLAIN, SELF-ALIGNING, CU-BE BALL, CRES RACE, (WITH GROOVED RACE) -65 F TO +350 F AS81936/1 REV. A AS81936/1 SHEET 2 OF 4 REV.A TABLE 1 - DIMENSIONS DASH NUMBER B D E H K L M N P Q R S W LUBE GROOVES AND HOLES IN RACE ONLY LUBE GROOVES AND HOLES IN BALL AND RACE BORE +.0000 .0005 OUTSI

8、DE DIA +.0000 .0005 +.000 .010 RACE WIDTH+.000 .005 BALLDIA MAX LUBE HOLE DIATHRU RACE AND BALL GROOVEWIDTH IDSWAGING RACE SHALL NOT RESTRICT GREASE FLOW. NOTES: 1. DASH NUMBER DESIGNATES NOMINAL BORE DIA IN SIXTEENTHS OF AN INCH. 2. EXAMPLE OF PART NO. M81936/1 -4 R T = .2500 INCH NOMINAL SIZE, LUB

9、RICATION GROOVES AND HOLES IN RACE ONLY. .010” OVERSIZE O.D.ABSENCE OF LETTER “T” AND “U”, INDICATES STANDARD RACE OF OUTER DIA (O.D.), DIMENSION “ D” (SEE TABLE 1).“T” = INDICATES FIRST OVERSIZE RACE O.D., DIMENSION “ D” (SEE TABLE 3).“U” = INDICATES SECOND OVERSIZE RACE O.D., DIMENSION “ D” (SEE T

10、ABLE 3).ABSENCE OF LETTER “R” INDICATES LUBRICATION GROOVES AND GREASE HOLES IN BALL AND RACE.“R” INDICATES LUBRICATION GROOVES AND GREASE HOLES IN RACE ONLY.NOMINAL BORE DIA. IN MULTIPLES OF ONE SIXTEENTH OF AN INCH (SEE TABLE 1).BASIC PART NUMBER3. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF TH

11、IS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 4. REFERENCED GOVERNMENT (OR NON-GOVERNMENT) DOCUMENTS OF THE ISSUE LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS DODISS SPECIFIED IN THE SOLICITATION FORM A PART O

12、F THIS STANDARD TO THE EXTENT SPECIFIED HEREIN. 5. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.