SAE AS 81969 16-2015 INSTALLING AND REMOVAL TOOLS CONNECTOR ELECTRICAL CONTACT TYPE III CLASS 1 COMPOSITION B.pdf

1、 AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE III, CLASS 1, COMPOSITION BAS81969/16Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, el

2、ectronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED

3、2015-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/16 SHEET 1 OF 5 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is ent

4、irelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites

5、yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/16 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/16 WITH THIS AS SPECIF

6、ICATION, TO IMPROVE DRAWING LEGIBILITY, AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. FIGURE 1 - INSTALLING AND REMOVAL TOOL (-01 AND -02) AEROSPACE STANDARD AS81969/16 SHEET 2 OF

7、5 INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE III, CLASS 1, COMPOSITION B FIGURE 1 - INSTALLING AND REMOVAL TOOL (-01 AND -02) CONTINUED FIGURE 2 - INSTALLING AND REMOVAL TOOL (-03) AEROSPACE STANDARD AS81969/16 SHEET 3 OF 5 INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL C

8、ONTACT, TYPE III, CLASS 1, COMPOSITION B FIGURE 2 - INSTALLING AND REMOVAL TOOL (-03) CONTINUED FIGURE 3 - INSTALLING AND REMOVAL TOOL (-04) AEROSPACE STANDARD AS81969/16 SHEET 4 OF 5 INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE III, CLASS 1, COMPOSITION B FIGURE 3 - INSTALLING

9、AND REMOVAL TOOL (-04) CONTINUED TABLE 1 - METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .003 0.08 .019 0.48 .146 3.71 .005 0.13 .0215 0.55 .147 3.73 .006 0.15 .022 0.56 .150 3.81 .0065 0.17 .0235 0.60 .181 4.60 .0070 0.18 .035 0.89 .185 4.70 .0075 0.19 .042 1.07 .245 6

10、.22 .0085 0.22 .045 1.14 .250 6.35 .0095 0.24 .046 1.17 .290 7.37 .010 0.25 .050 1.27 .325 8.26 .0105 0.27 .060 1.52 .330 8.38 .011 0.28 .068 1.73 .340 8.64 .0115 0.29 .071 1.80 .480 12.19 .012 0.30 .075 1.91 .515 13.08 .013 0.33 .082 2.08 .530 13.46 .0135 0.34 .084 2.13 .565 14.35 .014 0.36 .098 2.

11、49 .860 21.84 .016 0.41 .103 2.62 4.000 101.60.017 0.43 .117 2.97 4.500 114.30 .018 0.46 .130 3.30 .0185 0.47 .133 3.38 AEROSPACE STANDARD AS81969/16 SHEET 5 OF 5 INSTALLING AND REMOVAL TOOLS, CONNECTOR, ELECTRICAL CONTACT, TYPE III, CLASS 1, COMPOSITION B TABLE 2 - DASH NUMBERS, CONTACT SIZES, DIME

12、NSIONS AND SUPERSEDED PART NUMBERS DASH NUMBER CONTACT SIZE COLOR CODE FIGURE A I.D. .002 (.05) B O.D. .002 (.05) C DIA. D DIA. E DIA. SUPERSEDED PART # INSTALLING TIP REMOVAL TIP -01 20 RED WHITE 1 .058 (1.47) .092 (2.34) .110 (2.79) .130 (3.30) .090 (2.29) MS3160-20 -02 16 BLUE 1 .088 (2.24) .128

13、(3.25) .160 (4.06) .190 (4.83) .110 (2.79) MS3160-16 -03 12 YELLOW 2 SEE FIGURE 2 FOR DIMENSIONS MS3160-12 -04 22 GREEN 3 SEE FIGURE 3 FOR DIMENSIONS MS3160-22 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TOOL SHALL BE DESIGNED IN ACCO

14、RDANCE WITH FIGURES 1 THROUGH 3 AND TABLE 2. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. SLOT DESIGN SHALL ALLOW ALL APPLICABLE WIRE SIZES TO SNAP INTO THE TOOL FREELY. TOOL TIPS SHALL BE SMOOTH AND FREE F

15、ROM BURRS, NICKS, AND SHARP EDGES. 2. MARKING: EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON THE HANDLE WITH THE MANUFACTURERS IDENTIFICATION AND PART NUMBER IN ACCORDANCE WITH MIL-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. THE PART NUMBER SHALL BE AS SHOWN IN

16、 EXAMPLE BELOW: M81969 /16 - 01 BASE SPECIFICATION DETAIL SHEET DASH NUMBER (SEE TABLE 2) 3. QUALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS81969 WITH THE FOLLOWING EXCEPTIONS: PLUNGER FORCE - NOT REQUIRED APPLICATION NOTES: 1. THIS TOOL SHALL BE USED TO INSTALL AND REMOVE CONTACTS FROM

17、CONNECTORS SPECIFIED IN AS81511 SERIES 3 AND 4, AND AS29600 CONNECTORS AS SPECIFIED ON AS29600/23 AND /24 CONTACT SPECIFICATIONS. 2. THIS DOCUMENT SUPERSEDES MIL-I-81969/16A DATED 11 JANUARY 1979 AND MS3160 DATED 8 OCTOBER 1971. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS

18、FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.