SAE AS 81969 20-2015 INSTALLING AND REMOVAL TOOLS CONNECTOR ELECTRICAL CONTACT TYPE II CLASS 1 COMPOSITION A.pdf

1、 AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION A AS81969/20Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, ele

2、ctronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2

3、015-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/20 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is enti

4、relyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites y

5、ourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/20 RATIONALE AS81969/20 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/20A WITH THIS DOCUMENT. IT INCLUDES ENGINEERING POSITION

6、LETTERS, MILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS PRODUCT AND THE LATEST ISSUE OF

7、 AS81969. FIGURE 1 - BASIC TOOL DESCRIPTION FIGURE 2 - PROBE DIMENSIONS FOR SIZE 16 AND 20 CONTACTS AEROSPACE STANDARD AS81969/20 SHEET 2 OF 3 INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION A FIGURE 3 - PROBE DIMENSIONS FOR SIZE 22 CONTACTS REQUIREMENTS: AL

8、L REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. CONFIGURATION: TOOL CONFIGURATION SHALL BE IN ACCORDANCE WITH FIGURES 1, 2, AND 3. DIMENSIONS AND TOLERANCES ARE IN ACCORDANCE WITH ANSI Y14.5M. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED TOLERANCE IS .005 ON

9、 THREE PLACE DECIMALS, .01 ON TWO PLACE DECIMALS AND 4. DIAMETER DIMENSION .104 SHALL BE .500 INCH DEEP FROM THE END OF TIP (SEE FIGURE 2). HANDLE CONFIGURATION OPTIONAL WITHIN MAXIMUM DIMENSIONS SHOWN (SEE FIGURE 1). EACH TOOL SHALL BE FURNISHED WITH A PROTECTIVE PROBE CAP. THE CAP DESIGN AND MATER

10、IAL IS OPTIONAL (SEE APPLICATION NOTE). PROBE COMPRESSION SPRING FORCE SHALL BE 3.0 POUNDS 1.0 POUND. 2. IDENTIFICATION MARKING: EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON TOOL BODY IN ACCORDANCE WITH MIL-STD-130 (LOCATION OPTIONAL). TOOL IDENTIFICATION SHALL INCLUDE SAE PART NUMBER, SUPPL

11、IER PART NUMBER, AND SUPPLIER NAME OR SYMBOL IN ACCORDANCE WITH AIR1351. AEROSPACE STANDARD AS81969/20 SHEET 3 OF 3 INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE II, CLASS 1, COMPOSITION A 3. MATERIALS: HANDLE SHALL BE ALUMINUM ALLOY 6061-T1 OR EQUIVALENT. HANDLE FINISH SHALL BE G

12、REEN ANODIZED. NOSE SHALL BE STEEL 6150 OR S1 HEAT TREATED TO ROCKWELL C 50-54 OR EQUIVALENT. NOSE FINISH SHALL BE BLACK OXIDE. PROBE SHALL BE 303 STAINLESS STEEL OR EQUAVALENT. PLATING AS NEEDED TO MEET REQUIREMENTS. SPRING SHALL BE STEEL (SEE FIGURE 1). 4. PART NUMBER: M81969 /20 -01 I I I I I I_

13、DASH NUMBER (SEE TABLE 1) I I_ DETAIL SPECIFICATION NUMBER I_ BASIC SPECIFICATION NUMBER APPLICATION NOTES: 1. TOOLS SHALL BE USED TO INSTALL CONTACTS IN CONNECTORS SPECIFIED IN TABLE 1. TABLE 1 - TOOL APPLICATION PART NUMBER M81969/20 CONTACT SIZE CONNECTOR -01 16 AND 20 MIL-DTL-28748 -02 22 2. AS8

14、1969/20 DETAIL SPECIFICATION SUPERSEDES THE MIL-I-81969/20A DETAIL SPECIFICATION. PART NUMBERS REMAIN UNCHANGED. 3. THE PROTECTION CAP (SEE FIGURE 1) MINIMIZES DAMAGE TO THE TIP AND IMPROVES PERSONNEL SAFETY. IF LOST, CONTACT THE SUPPLIER FOR REPLACEMENT. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOC

15、ATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.