SAE AS 81969 5-2015 INSTALLING TOOLS CONNECTOR ELECTRICAL CONTACT (FORK TYPE CRIMP REMOVABLE) TYPE I CLASS 1 COMPOSITION A.pdf

1、 AEROSPACE STANDARD INSTALLING TOOLS, CONNECTOR, ELECTRICAL CONTACT,(FORK TYPE, CRIMP REMOVABLE) TYPE I, CLASS 1, COMPOSITION A AS81969/5Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by

2、 any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.s

3、ae.org ISSUED 2015-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120AS81969/5 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis

4、report is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled.

5、 SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/5 RATIONALE THIS DETAIL SPECIFICATION SHEET IS REQUIRED TO ALLOW THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/5 WITH THI

6、S DOCUMENT, TO MODIFY QUALIFICATION INFORMATION, TO REMOVE THE REDUNDANT .040 RADIUS DIMENSION IN DETAIL A, TO IMPROVE DRAWING LEGIBILITY, TO REMOVE GOVERNMENT JARGON AND TO UPDATE REFERENCES. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT

7、AND THE LATEST ISSUE OF AS81969. FIGURE 1 - INSTALLING TOOL CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS81969/5 SHEET 2 OF 2 INSTALLING TOOLS, CONNECTOR, ELECTRICAL CONTACT, (FORK TYPE, CRIMP REMOVABLE) TYPE I, CLASS 1, COMPOSITION A TABLE 1 - METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLI

8、METERS INCHES MILLIMETERS .002 0.051 .050 1.27 .375 9.52 .003 0.076 .052 1.32 .750 19.05.022 0.559 .06 1.52 1.250 31.75 .038 0.965 .080 2.03 2.500 63.50.040 1.02 .125 3.18 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. DESIGN: THE TOOL SHALL BE DESI

9、GNED IN ACCORDANCE WITH FIGURE 1. DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .015 INCH (0.38 MILLIMETERS). 2. MATERIAL AND FINISHES: HANDLE: ALUMINUM INSTALLING TI

10、P: DRILL ROD HARDENED PLATING: HANDLE-NOT APPLICABLE, ANODIZED ONLY INSTALLING TIP: DECORATIVE CHROME, .0001 INCH THICKNESS. 3. PART NUMBER/MARKING: M81969/5-01 EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON THE HANDLE WITH THE MANUFACTURERS IDENTIFICATION AND PART NUMBER IN ACCORDANCE WITH MI

11、L-STD-130. MANUFACTURER SYMBOL, IF USED, SHALL BE IN ACCORDANCE WITH AIR1351. 4. QUALIFICATION: QUALIFICATION SHALL BE IN ACCORDANCE WITH AS81969 WITH THE FOLLOWING EXCEPTIONS: ROTATION - NOT APPLICABLE THRUST - NOT APPLICABLE IMPACT STRENGTH - NOT APPLICABLE ALTERNATIVE QUALIFICATION REQUIREMENTS S

12、UCH AS CERTIFICATION, FIRST ARTICLE OR QC TESTING MAY BE IMPOSED BY THE QUALIFYING ACTIVITY (QA). THE QA SHALL SUBMIT A WRITTEN REQUEST TO THE AE-8C2 COMMITTEE FOR REVIEW AND APPROVAL OF THE ALTERNATIVE QUALIFICATION TESTING PROGRAM PRIOR TO IMPLEMENTATION OF THE REQUIREMENT. APPLICATION NOTES: 1. T

13、HIS TOOL SHALL BE USED TO INSTALL CONTACTS AS SPECIFIED IN MIL-DTL-55302/93 THROUGH /96 AND /99 THROUGH /104. 2. THIS DOCUMENT SUPERSEDES MIL-I-81969/5A DATED 11 JANUARY 1979 AND MIL-C-55302/105 (EL) DATED 30 MAY 1975. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CO

14、NVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.