SAE AS 83461 2C-2016 STRAIGHT THREAD TUBE FITTING BOSS O-RING MOLDED FROM AMS-P-83461 RUBBER.pdf

1、AEROSPACE STANDARD STRAIGHT THREAD TUBE FITTING BOSS O-RING MOLDED FROM AMS-P-83461 RUBBER AS83461/2 Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical,

2、photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2009-09REVISED2016-10TH

3、IRD ANGLE PROJECTION CUSTODIAN: A-6/A-6C REV.CFEDERAL SUPPLY CLASS 5331 AS83461/2 SHEET 1 OF 3REV. CPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report is publishedbySAEtoadvance thestateoftechnical and engineeringsciences. The useofthis reportisentirely vol

4、untary, and its applicabilityand suitability for any particularuse, includingany patent infringement arising therefrom, isthe soleresponsibility of the user.”SAE reviews each technical report at least every five years at whichtime it mayberevised, reaffirmed, stabilized, or cancelled. SAE invites yo

5、ur writtencomments and suggestions. SAE values your input. To provide feedback on thisTechnical Report, please visit http:/standards.sae.org/AS83461/2CRATIONALE THIS STANDARD HAS BEEN REVISED TO INCORPORATE MINOR TECHNICAL CHANGES. FOREWORD THIS STANDARD ESTABLISHES THE DIMENSIONAL AND VISUAL QUALIT

6、Y REQUIREMENTS, LOT REQUIREMENTS AND PACKAGING AND LABELING REQUIREMENTS FOR O-RINGS MOLDED FROM AMS-P-83461 RUBBER. IT SHALL BE USED FOR PROCUREMENT PURPOSES. NOTE: DIMENSION AND TOLERANCING PER ASME Y14.5 FIGURE 1 - O-RING DIMENSIONS: WIDTH (W) AND INSIDE (D) DIAMETERS TABLE 1 - PART NUMBERS AND D

7、IMENSIONS PARTNUMBER NOMINAL TUBE OUTSIDE DIAMETER D W APPROX MASS (IN) (MM) (IN) (MM) (IN) (MM) (LB/100) (KG/100)M83461/2-901 .094 2.381 .180/ .190 4.572/ 4.826 .053/.059 1.346/1.499 .006 0.003 M83461/2-902 .125 3.175 .234/ .244 5.944/ 6.198 .061/.067 1.549/1.702 .011 0.005 M83461/2-903 .188 4.775

8、296/ .306 7.518/ 7.772 .061/.067 1.549/1.702 .013 0.006 M83461/2-904 .250 6.350 .346/ .356 8.788/ 9.042 .069/.075 1.753/1.905 .020 0.009 M83461/2-905 .312 7.950 .409/ .419 10.389/10.643 .069/.075 1.753/1.905 .023 0.011 M83461/2-906 .375 9.525 .463/ .473 11.760/12.014 .075/.081 1.905/2.057 .031 0.01

9、4 M83461/2-907 .438 11.113 .523/ .537 13.284/13.640 .079/.085 2.007/2.159 .039 0.018 M83461/2-908 .500 12.700 .635/ .653 16.129/16.586 .084/.090 2.134/2.286 .053 0.024 M83461/2-909 .562 14.288 .697/ .715 17.704/18.161 .094/.100 2.388/2.540 .073 0.033 M83461/2-910 .625 15.875 .746/ .764 18.948/19.406

10、 .094/.100 2.388/2.540 .078 0.035 M83461/2-911 .688 17.463 .854/ .872 21.692/22.149 .112/.120 2.845/3.048 .126 0.057 M83461/2-912 .750 19.050 .915/ .933 23.241/23.698 .112/.120 2.845/3.048 .135 0.061 M83461/2-913 .812 20.638 .976/ .996 24.790/25.298 .112/.120 2.845/3.048 .145 0.066 M83461/2-914 .875

11、 22.225 1.037/1.057 26.340/26.848 .112/.120 2.845/3.048 .153 0.070 M83461/2-916 1.000 25.400 1.161/1.181 29.489/29.997 .112/.120 2.845/3.048 .172 0.078 M83461/2-918 1.125 28.575 1.343/1.367 34.112/34.722 .112/.120 2.845/3.048 .199 0.090 M83461/2-920 1.250 31.750 1.461/1.489 37.109/37.821 .114/.122 2

12、896/3.099 .224 0.102 M83461/2-924 1.500 38.100 1.706/1.734 43.332/44.044 .114/.122 2.896/3.099 .261 0.118 M83461/2-928 1.750 44.450 2.072/2.108 52.629/53.543 .114/.122 2.896/3.099 .317 0.144 M83461/2-932 2.000 50.800 2.319/2.355 58.903/59.817 .114/.122 2.896/3.099 .354 0.161 AEROSPACE STANDARD AS83

13、461/2 SHEET 2 OF 3REV. CSTRAIGHT THREAD TUBE FITTING BOSS O-RING MOLDED FROM AMS-P-83461 RUBBER 1. APPLICATION THESE O-RINGS TYPICALLY HAVE BEEN USED AS SEALS ON STRAIGHT-THREADED, FLARED-TUBE CONNECTION FITTINGS IN AEROSPACE APPLICATIONS FOR CONTACT WITH AIR AND HYDRAULIC FLUIDS CONFORMING TO MIL-P

14、RF-83282 AND MIL-PRF-87257 AND IN LAND VEHICLE APPLICATIONS FOR CONTACT WITH AIR AND HYDRAULIC FLUIDS CONFORMING TO MIL-PRF-83282, MIL-PRF-46170, AND MIL-PRF-87257 BUT USAGE IS NOT LIMITED TO SUCH APPLICATIONS. EACH APPLICATION SHOULD BE CONSIDERED SEPARATELY. THESE O-RINGS HAVE A SERVICE TEMPERATUR

15、E RANGE OF -65 TO +275 F (-54 TO +135 C). 2. APPLICABLE REFERENCES 2.1 SAE PUBLICATIONS AVAILABLE FROM SAE INTERNATIONAL, 400 COMMONWEALTH DRIVE, WARRENDALE, PA 15096-0001, TEL: 877-606-7323 (INSIDE USA AND CANADA) OR +1 724-776-4970 (OUTSIDE USA), www.sae.org.AMS2817 PACKAGING AND IDENTIFICATION, P

16、REFORMED PACKINGS AMS-P-83461 PACKING, PREFORMED, PETROLEUM HYDRAULIC FLUID RESISTANT, IMPROVED PERFORMANCE AT 275F (135C) ARP5316 STORAGE OF ELASTOMER SEALS AND SEAL ASSEMBLIES WHICH INCLUDE AN ELASTOMER ELEMENT PRIOR TO HARDWARE ASSEMBLY 2.2 ASME PUBLICATIONS AVAILABLE FROM ASME, P.O. BOX 2900, 22

17、 LAW DRIVE, FAIRFIELD, NJ 07007-2900, TEL: 800-843-2763 (U.S./CANADA), 001-800-843-2763 (MEXICO), 973-882-1170 (OUTSIDE NORTH AMERICA), www.asme.org.ASME Y14.5-2009 DIMENSIONING AND TOLERANCING 2.3 ASQ PUBLICATIONS AVAILABLE FROM AMERICAN SOCIETY FOR QUALITY, 600 NORTH PLANKINTON AVENUE, MILWAUKEE,

18、WI 53203, TEL: 800-248-1946 (UNITED STATES OR CANADA), 001-800-514-1564 (MEXICO) OR +1-414-272-8575 (ALL OTHER LOCATIONS), www.asq.org.ANSI/ASQ Z1.4 SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES 2.4 ISO PUBLICATIONS COPIES OF THESE DOCUMENTS ARE AVAILABLE ONLINE AT http:/webstore.ansi.

19、org/.ISO 3601-1 FLUID POWER SYSTEMS - O-RINGS - PART 1: INSIDE DIAMETERS, CROSS-SECTIONS, TOLERANCES AND DESIGNATION CODES ISO 3601-3 FLUID POWER SYSTEMS - O-RINGS - PART 3: QUALITY ACCEPTANCE CRITERIA 2.5 U.S. GOVERNMENT PUBLICATIONS COPIES OF THESE DOCUMENTS ARE AVAILABLE ONLINE AT http:/quicksear

20、ch.dla.mil.MIL-PRF-46170 HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE MIL-PRF-83282 HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, AIRCRAFT, METRIC MIL-PRF-87257 HYDRAULIC FLUID, PETROLEUM BASE, FOR PRESERVATION AND OPERATION 3. REQUIREMENTS 3.1 PART NUMBER: THE O-RING P

21、ART NUMBERS ARE DESIGNATED AS MS83461/1-9XX, WHERE 9XX INDICATES THE DASH SIZE. 3.2 DO NOT USE UNASSIGNED PART NUMBERS. 3.3 MATERIAL: THE MATERIAL SHALL BE IN ACCORDANCE WITH AMS-P-83461. 3.4 DIMENSIONAL AND VISUAL INSPECTION: PRIOR TO INSPECTION, MOLD FLASH SHALL BE REMOVED FROM THE O-RINGS IN SUCH

22、 A MANNER THAT THEY CONFORM TO THE REQUIREMENTS SPECIFIED HEREIN. FOR END OF PROCESS INSPECTION, EACH INDIVIDUAL O-RING (100%) SHALL BE VISUALLY INSPECTED AT 1X MAGNIFICATION FOR MOLD FLASH, BACKRIND, PARTING LINE PROJECTION, NON-FILLS, FLOW LINES, AND OTHER SIGNIFICANT DEFECTS. THE ENTIRE O-RING SU

23、RFACE SHALL BE INSPECTED. AEROSPACE STANDARD AS83461/2 SHEET 3 OF 3REV. CSTRAIGHT THREAD TUBE FITTING BOSS O-RING MOLDED FROM AMS-P-83461 RUBBER 3.5 FOR FINAL INSPECTION, THE SAMPLE SIZE SHALL BE IN ACCORDANCE WITH ANSI/ASQ Z1.4 SINGLE SAMPLING PLAN INSPECTION LEVEL II WITH AN AQL 1.0 EXCEPT THAT TH

24、E ACCEPTANCE NUMBER SHALL BE ZERO. THE SAMPLE UNIT SHALL BE ONE O-RING. INSPECTION SHALL BE ACCORDING TO ISO 3601-3, GRADE S REQUIREMENTS UNDER 2X MAGNIFICATION. IN CASE OF DISAGREEMENT, THE VISUAL INSPECTION AT 2X MAGNIFICATION SHALL GOVERN. THE ENTIRE O-RING SURFACE SHALL BE MANUALLY INSPECTED. TH

25、E PROCEDURES OUTLINED IN ANNEX B OF ISO 3601-1 SHALL BE FOLLOWED FOR DIMENSIONAL INSPECTION. IF THE PURCHASER REQUIRES A DIFFERENT SAMPLING PLAN OR VISUAL INSPECTION CRITERIA, MANUFACTURER SHALL BE INFORMED PRIOR TO TIME OF ORDER. 3.6 THE MANUFACTURER OF THE O-RINGS SHALL BE RESPONSIBLE FOR THE REQU

26、IRED INSPECTIONS AND LOT ACCEPTANCE TESTS. PURCHASER RESERVES THE RIGHT TO SAMPLE AND PERFORM ANY CONFIRMATORY INSPECTION DEEMED NECESSARY TO ENSURE THAT THE O-RINGS CONFORM TO THE SPECIFIED REQUIREMENTS. 3.7 LOT ACCEPTANCE: THE REQUIREMENTS ARE LISTED IN AMS-P-83461. THE LOT CERTIFICATION REPORT SH

27、ALL BE FURNISHED TO THE PURCHASER WHEN THE PRODUCT IS SHIPPED. THE MANUFACTURER OF THE O-RINGS SHALL BE RESPONSIBLE FOR THE REQUIRED INSPECTIONS AND LOT ACCEPTANCE TESTS. PURCHASER RESERVES THE RIGHT TO SAMPLE AND PERFORM ANY CONFIRMATORY INSPECTION DEEMED NECESSARY TO ENSURE THAT THE O-RINGS CONFOR

28、M TO THE SPECIFIED REQUIREMENTS. 3.8 IDENTIFICATION AND PACKAGING: PACKAGING SHALL BE IN ACCORDANCE WITH AMS2817 WITH THE EXCEPTION THAT, IF REQUESTED BY CONTRACT, EACH PACKAGE SHALL BEAR THE FOLLOWING IDENTIFICATION OF A RECOGNIZABLE SIZE: x IF REQUIRED BY PURCHASER: NATIONAL STOCK NUMBER 3.9 PURCH

29、ASE DOCUMENTS SHOULD SPECIFY NOT LESS THAN THE FOLLOWING: x AMS-P-83461 MATERIAL x PART NUMBER OF O-RING PER AS83461/2 x QUANTITY OF O-RINGS DESIRED x SPECIAL PACKAGING, LABELING, AND INSPECTION, IF REQUIRED 3.10 DIMENSIONS AND PROPERTIES IN INCH UNITS ARE PRIMARY. DIMENSIONS AND PROPERTIES IN SI UN

30、ITS ARE SHOWN AS THE APPROXIMATE EQUIVALENTS OF THE PRIMARY UNITS AND ARE PRESENTED ONLY FOR INFORMATION. 3.11 SHELF LIFE REQUIREMENTS OF ARP5316 APPLY TO THESE O-RINGS. 4. NOTES 4.1 REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS

31、WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.