SAE AS 85049 142C-2012 CONNECTOR ACCESSORIES ELECTRICAL BOOTS AND SLEEVES TRANSITIONS HEAT-SHRINKABLE CATEGORY 7《分类7 热缩性 转换 电气启动和套筒连接器附件》.pdf

1、 AEROSPACE STANDARD CONNECTOR ACCESSORIES, ELECTRICAL BOOTS AND SLEEVES, TRANSITIONS, HEAT-SHRINKABLE, CATEGORY 7 AS85049/142 Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,

2、 electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSU

3、ED 2006-11REVISED2012-08REAFFIRMED 2017-10THIRD ANGLE PROJECTION CUSTODIAN: AS-8/AS-8C1 REV.C FEDERAL SUPPLY CLASS 4030 AS85049 /142 SHEET 1 OF 5 REV. C PROCUREMENT SPECIFICATION: AS85049 SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technica

4、land engineering sciences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be

5、 revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS85049/142C RATIONALE AS85049/142C HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW

6、POLICY. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF SAE AS85049. FIGURE 1 - BOOT, T-TYPE (SEE TABLE 1) TABLE 1 - DIMENSIONS FOR BOOT, T- TYPE (SEE FIGURE 1) DASH NUMBER H, J, K DIAMETER AS SUPPLIED MINIMUM H, J, K

7、 DIAMETER AS RECOVERED MAXIMUM P DIMENSION AS RECOVERED10% R DIMENSION AS RECOVERED10% S DIMENSION AS RECOVERED 10% T DIMENSION AS RECOVERED 10% W DIMENSION AS RECOVERED 20% 01 .26 .14 1.17 .58 .59 N/A .04 (6.6) (3.6) (29.7) (14.7) (15.0) (1.0)02 .52 .27 2.31 1.16 1.16 .69 .06 (13.2) (6.9) (58.7) (2

8、9.5) (29.5) (17.5) (1.5)03 1.06 .53 4.73 2.36 2.37 1.40 .09 (26.9) (13.5) (120.1) (59.9) (60.2) (35.6) (2.29)04 2.19 1.19 9.70 4.85 4.85 2.79 .12 (55.6) (30.2) (246.4) (123.2) (123.2) (70.9) (3.0)AEROSPACE STANDARD AS85049 /142 SHEET 2 OF 5 REV. C CONNECTOR ACCESSORIES, ELECTRICAL BOOTS AND SLEEVES,

9、 TRANSITIONS, HEAT-SHRINKABLE, CATEGORY 7 FIGURE 2 - BOOT, Y-TYPE (SEE TABLE 2) TABLE 2 - DIMENSIONS FOR BOOT, Y- TYPE (SEE FIGURE 2) DASH NUMBER H DIAMETER AS SUPPLIED MINIMUM H DIAMETER AS RECOVERED MAXIMUM J & K DIAMETER AS SUPPLIED MINIMUM J & K DIAMETER AS RECOVEREDMAXIMUM P DIMENSION AS RECOVE

10、REDREF R DIMENSION AS RECOVEREDREF S DIMENSIONAS RECOVERED10% T DIMENSION AS RECOVERED10% HW DIMENSION AS RECOVERED20% JW & KW DIMENSION AS RECOVERED20% 05 .52 .24 .26 .13 .88 .76 .94 .61 .06 .04 (13.2) (6.1) (6.6) (3.3) (22.4) (19.3) (23.9) (15.5) (1.5) (1.0)06 1.06 .49 .52 .24 1.50 1.70 2.10 1.30

11、10 .06 (26.9) (12.4) (13.2) (6.1) (38.1) (43.2) (53.3) (33.0) (2.5) (1.5)07 1.52 .71 1.06 .49 2.58 3.10 3.10 2.20 .12 .10 (38.6) (18.0) (26.9) (12.4) (65.5) (78.7) (78.7) (55.9) (3.0) (2.5)08 2.19 1.02 1.06 .50 3.35 3.70 4.40 2.80 .18 .10 (55.6) (25.9) (26.9) (12.7) (85.1) (94.0) (111.8) (71.1) (4.

12、6) (2.5)AEROSPACE STANDARD AS85049 /142 SHEET 3 OF 5 REV. C CONNECTOR ACCESSORIES, ELECTRICAL BOOTS AND SLEEVES, TRANSITIONS, HEAT-SHRINKABLE, CATEGORY 7 FIGURE 3 - BOOT, 1 TO 3 TYPE (SEE TABLE 3) TABLE 3 - DIMENSIONS FOR BOOT, 1 TO 3 TYPES (SEE FIGURE 3) DASH NUMBER H DIAMETER AS SUPPLIED MINIMUM H

13、 DIAMETER AS RECOVERED MAXIMUM J, K, L DIAMETER AS SUPPLIED MINIMUM J, K, L DIAMETER AS RECOVEREDMAXIMUM P DIMENSIONAS RECOVERED10% R DIMENSIONAS RECOVEREDREF S DIMENSIONAS RECOVEREDREF U DIMENSION AS RECOVERED10% T DIMENSION AS RECOVERED10% HW DIMENSIONAS RECOVERED20% W DIMENSIONAS RECOVERED20% 09

14、52 .26 .26 .14 1.82 1.00 .82 .62 1.20 .06 .04 (13.2) (6.6) (6.6) (3.6) (46.2) (25.4) (20.8) (15.7) (30.5) (1.5) (1.0)10 1.06 .53 .52 .27 3.67 1.98 1.69 1.30 2.25 .10 .06 (26.9) (13.5) (13.2) (6.9) (93.2) (50.3) (42.9) (33.0) (57.2) (2.5) (1.5)11 1.52 .75 .76 .38 5.32 2.90 2.42 1.80 3.50 .12 .07 (38

15、6) (19.1) (19.3) (9.7) (135.1) (73.7) (61.5) (45.7) (88.9) (3.0) (1.8)12 2.19 1.00 1.06 .49 7.56 4.06 3.50 2.80 4.80 .18 .12 (55.6) (25.4) (26.9) (12.4) (192.0) (103.1) (88.9) (71.1) (121.9) (4.6) (3.0)13 3.60 2.15 1.80 1.08 15.37 8.31 7.06 5.00 10.0 .28 .18 (91.4) (54.6) (45.7) (27.4) (390.4) (211

16、1) (179.3) (127.0) (254.0) (7.1) (4.6)AEROSPACE STANDARD AS85049 /142 SHEET 4 OF 5 REV. C CONNECTOR ACCESSORIES, ELECTRICAL BOOTS AND SLEEVES, TRANSITIONS, HEAT-SHRINKABLE, CATEGORY 7 TABLE 4 - AVAILABLE MATERIALS MATERIAL DESIGNATOR 2/ MATERIAL 4/ OPERATING TEMPERATURE RANGE MATERIAL DESIGNATOR CO

17、LOR STRIPE 2/ SHRINK TEMPERATURE 3/ A 1/ POLYOLEFIN SEMI-RIGID -55 TO +135 C (-67 TO +275 F) WHITE 121 C (250 F) B 1/ POLYOLEFIN FLEXIBLE -55 TO +135 C ( -67 TO +275 F) RED 100 C (212 F) C SILICONE -75 TO +180 C (-103 TO +356 F) ORANGE 135 C (275 F) D FLEXIBLE FLUORO-ELASTOMER -55 TO +200 C ( -67 TO

18、 +392 F) YELLOW 175 C (347 F) G 1/ POLYOLEFIN -30 TO +105 C (-22 TO +221 F) GREEN 120 C (248 F) H 1/ ELASTOMERIC -75 TO +150 C (-103 TO +275 F) BLUE 135 C (275 F) 1/ OPTIONAL ADHESIVE MATERIAL APPLIED ON INSIDE SURFACE SHALL BE CONTROLLED BY THE SUPPLIER TO MAINTAIN THE ADHESION AT OPERATING TEMPERA

19、TURE. 2/ MATERIAL DESIGNATOR SHALL BE A CONTINUOUS COLOR STRIPE RING, APPROXIMATELY 1/8 INCH WIDE, OR AN ENCIRCLED MATERIAL DESIGNATOR LOCATED AS SHOWN IN FIGURES 1 THRU 3. COLOR OR MATERIAL DESIGNATOR SHALL REMAIN DISTINGUISHABLE OVER THE SPECIFIED TEMPERATURE RANGE. THE SIZE OF THE MATERIAL DESIGN

20、ATOR SHALL BE RECOGNIZABLE AFTER RECOVERED, AND THE COLOR SHALL BE CONTRASTING TO THE COLOR OF THE BOOT AT THE MANUFACTURERS CHOICE. 3/ COMPONENTS SHRINK UPON APPLICATION OF HEAT IN EXCESS OF VALUES LISTED. 4/ MATERIAL SHALL BE CERTIFIED TO AS5258. REQUIREMENTS: CONNECTOR ACCESSORY DESIGN AND CONSTR

21、UCTION: 1. DIMENSIONS AND CONFIGURATIONS AS SPECIFIED IN FIGURES 1 THRU 3 AND TABLES 1 THRU 3. DIMENSIONS H AND J REDUCED BY .06 INCH (1.5 MM) WHEN ADHESIVE IS USED (SEE EXAMPLE PART NUMBER). DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES SHALL BE: .XX = .020 (0.51 MM), .XXX = .010

22、 (0.25 MM). METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 25.4 MM = 1 INCH. METRIC EQUIVALENTS ARE SHOWN IN PARENTHESES. 2. MATERIAL TYPE AND IDENTIFICATION AS SPECIFIED IN TABLE 4 3. PART OR IDENTIFYING NUMBER (PIN) EXAMPLE: M85049/ 142 - 05 H C P BASIC PART NUMBER SPEC

23、IFICATION SHEET DASH # (TABLES 1 THRU 3) MATERIAL DESIGNATOR (TABLE 4) ADHESIVE: C = COATED U = UNCOATED INJECTION-VENT PORT (OMIT FOR NO INJECTION-VENT PORT) AEROSPACE STANDARD AS85049 /142 SHEET 5 OF 5 REV. C CONNECTOR ACCESSORIES, ELECTRICAL BOOTS AND SLEEVES, TRANSITIONS, HEAT-SHRINKABLE, CATEGO

24、RY 7 QUALIFICATIONS: THE CONNECTOR ACCESSORIES SHALL MEET QUALIFICATION REQUIREMENTS OF SAE AS85049 CATEGORY 7 AND HEREIN. ONLY QUALIFICATION BY CERTIFICATION OF DIMENSIONS AND MATERIALS IS REQUIRED. SUPERSESSION DATA: SUPERSESSION DATA FOR REFERENCE ONLY. ALL DASH NUMBERS MAY NOT CORRESPOND BETWEEN

25、 SPECIFICATIONS. CONSULT INDIVIDUAL SPECIFICATIONS FOR EXACT CROSS REFERENCE. AS5258/ 7 * * * 8 9 ADHESIVE (C - COATED, U - UNCOATED) DASH NUMBER MATERIAL TYPE (SEE TABLE 5) TABLE 5 - AS5258/7, /8, /9 SUPERSEDED BY AS85049/142 CROSS REFERENCE DASH # MATERIAL ADHESIVE INJECTION-VENT PORTS AS5258 /142

26、 AS5258 /142 AS5258 /142 AS5258 /142 M5258/7- 01 THRU 04 01 THRU 04 A B C D G H A B C D G H C U C U NONE BLANK M5258/8- 01 THRU 04 05 THRU 08 M5258/9- 01 THRU 04 09 THRU 12 APPLICATION NOTES: 1. MAY BE USED AS TRANSITIONAL JUNCTION FOR ELECTRICAL WIRING. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCA

27、TED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.