SAE AS 85421 10C-2008 FITTING ADAPTER BEAM SEAL 3000 4000 PSI MALE TO FLARELESS《非扩口外螺纹3000 4000 psi光束密封装配适配器》.pdf

1、 AEROSPACE STANDARD FITTING, ADAPTER, BEAM SEAL, 3000/4000 PSI, MALE TO FLARELESS AS85421/10 Copyright 2008 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocop

2、ying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2002-01REVISED 2008-01 THIRD ANGL

3、E PROJECTION CUSTODIAN: SAE G-3 REV. C FEDERAL SUPPLY CLASS4730 AS85421/10SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: AS85421 /4/SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences. Theuse of thisreportis entire

4、ly voluntary, andits applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelled.SAE invites yourwritten

5、 commentsandsuggestions.RATIONALE REVISED THE WEIGHT SPECIFICATIONS BASED ON SOLID MODELS OF EACH FITTING. FIGURE 1 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD FITTING, ADAPTER

6、, BEAM SEAL, 3000/4000 PSI, MALE TO FLARELESS AS85421/10 SHEET 2 OF 3 REV. C TABLE 1 - DIMENSIONAL DATA MASS, LB/EA, APPROX, REF DASH NO. TUBE OD S THREAD AS8879 T THREAD AS8879 A B REF C REF E (MIN) TI CRES -03 .188 .3750-24UNJF-3A .3750-28UNJS-3A .855 .375 .200 .350 .021 .038 -04 .250 .4375-20UNJF

7、-3A .4375-24UNJS-3A .960 .438 .232 .413 .030 .052 -05 .313 .5000-20UNJF-3A .5000-24UNJS-3A .970 .500 .242 .475 .036 .064 -06 .375 .5625-18UNJF-3A .5625-20UNJS-3A 1.052 .562 .288 .537 .046 .081 -08 .500 .7500-16UNJF-3A .7188-20UNJS-3A 1.170 .750 .300 .725 .077 .137 -10 .625 .8750-14UNJF-3A .8438-18UN

8、JS-3A 1.303 .875 .306 .850 .102 .181 -12 .750 1.0625-12UNJ-3A 1.0000-16UNJ-3A 1.480 1.000 .380 .975 .156 .276 -16 1.000 1.3125-12UNJ-3A 1.2500-14UNJS-3A 1.560 1.250 .412 1.225 .219 .388 -20 1.250 1.6250-12UNJ-3A 1.5781-14UNJS-3A 1.583 1.625 .438 1.600 .313 .553 -24 1.500 1.8750-12UNJ-3A 1.8438-14UNJ

9、S-3A 1.668 1.875 .438 1.850 .395 .699 SIZES -20 AND -24 WERE ORIGINALLY DESIGNATED AS SIZES -21 AND -25 ON SOME MANUFACTURERS DRAWINGS. THESE SIZES WILL NOT CONNECT WITH THE ORIGINAL -20 AND -24 FITTINGS. SEE 6.4 IN THE PROCUREMENT SPECIFICATION FOR ADDITIONAL INFORMATION. NOTES: /1/ MATERIAL: a. CO

10、DE LETTER P - TYPE 17-4PH CORROSION RESISTANT STEEL PER AMS 5643. b. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS 4928 OR AMS 4965. c. CODE LETTER V - TYPE 15-5PH, CORROSION RESISTANT STEEL PER AMS 5659. 2. HEAT TREATMENT: a. MATERIAL CODE LETTER P - CONDITION H1075 PER AMS 2759/3. b. MATE

11、RIAL CODE LETTER T - NONE. c. MATERIAL CODE LETTER V - AGE TO CONDITION H 1075 PER AMS-H-6875 OR AMS 2759/3. 3. FINISH: a. MATERIAL CODE LETTER P - PASSIVATE PER AMS 2700, TYPE 6 OR 7. b. MATERIAL CODE LETTER T - FLUORIDE PHOSPHATE CONVERSION COAT PER AMS 2486 WITH COLOR GREY SIMILAR TO FED-STD-595,

12、 COLOR NUMBER 36076 THROUGH 36293. HOWEVER, IF COLOR DOES NOT EXACTLY MATCH GREY IT SHALL NOT CAUSE REJECTION OF THE FITTING. c. MATERIAL CODE LETTER V - PASSIVATE PER AMS 2700, TYPE 6 OR 7. /4/ PROCUREMENT SPECIFICATION: AS85421 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFI

13、CATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS85421 FOR THIS STANDARD. SEE WW.EAUDITNET.COM FOR CURRENT QPL ON-LINE. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3,

14、 15A3, OR 15B. a. FOR SIZES 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER, AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING. b. FOR SIZES 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE

15、LETTER, AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD FITTING, ADAPTER, BEAM SEAL, 3000/4000 PSI, MALE TO FLARELE

16、SS AS85421/10 SHEET 3 OF 3 REV. C 6. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE“ MAY BE USED TO DEPLETION. 7. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. CORROSION RESISTANT STEEL AT 3000 psi. b. TITANIUM ALLOY AT 4000 psi.

17、8. DRY FILM LUBRICANT: APPLY DRY FILM LUBRICANT PER AS5272, TYPE I TO SEALING SURFACE. OVERSPRAY IN BORE IS NOT PERMITTED. 9. INTERPRETATION OF DRAWING PER ARP4296. 10. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in

18、Ra. FORGED SURFACES MAY BE 250 in Ra. 11. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 12. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 13. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS +.015, ANGULAR DIMENSIONS +030 14. EXAMPLE OF PART NUMBER: AS85421/10

19、 V 06 SIZE CODE, TUBE SIZE IN SIXTEENTHS IN .0625 INCREMENTS MATERIAL CODE LETTER /1/ BASIC PART NUMBER 15. IN THE EVENT OF CONFLICT BETWEEN THE TEXT OF THIS DOCUMENT AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS DOCUMENT TAKES PRECEDENCE. NOTHING IN THIS DOCUMENT, HOWEVER, SUPERSEDES APPLICABLE

20、 LAWS AND REGULATIONS UNLESS A SPECIFIC EXEMPTION HAS BEEN OBTAINED. 16. TITANIUM IS NOT RECOMMENDED FOR USE IN GASEOUS OR LIQUID OXYGEN SYSTEMS. 17. USERS ARE CAUTIONED WHEN INSTALLING SIZES -03 THROUGH -06. THE ONLY DIFFRENCE BETWEEN THE TWO ENDS IS THE NUMBER OF THREADS. 18. THE CHANGE BAR ( l )

21、LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-