SAE AS 90328-2000 CABLE ASSEMBLY EXTERNAL ELECTRIC POWER AIRCRAFT 115 200 VOLT 400 HERTZ《飞机电缆组件外部电力为115 200 V 400 Hertz FSC 6150[代替 海军 MS90328 版本G 作废公告1 海军 MS90328 版本G 海军 MS90328 版.pdf

1、SHEET 1 OF 4AS90328THIRD ANGLE PROJECTIONAEROSPACE STANDARDAS90328ISSUED 2000-03 REAFFIRMED 2009-09CABLE ASSEMBLYEXTERNAL ELECTRIC POWER,AIRCRAFT 115/200 VOLT, 400 HERTZPREPARED BY SAE SUBCOMMITTEE AE-8FFEDERAL SUPPLY CLASS 6150NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICA

2、TION MS90328G AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS90328G. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAI

3、N UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF P

4、ORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED P

5、RODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retri

6、eval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: Custom

7、erServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,includin

8、g any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technic

9、al Report, please visit http:/www.sae.org/technical/standards/AS90328 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CABLE ASSEMBLYEXTERNAL ELECTRIC POWER,AIRCRAFT 115/200 VOLT, 400 HERTZAEROSPACE S

10、TANDARDAS90328SHEET 2 OF 4AS90328THE REQUIREMENTS FOR ACQUIRING THE PRODUCT(S) DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE ISSUE OF THE FOLLOWING SPECIFICATION LISTED IN THAT ISSUE OF THE DODISS SPECIFIED IN THE SOLICITATION: MIL-C-7974.TABLE I. CABLE ASSEMBLY.Copyright SAE In

11、ternational Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CABLE ASSEMBLYEXTERNAL ELECTRIC POWER,AIRCRAFT 115/200 VOLT, 400 HERTZAEROSPACE STANDARDAS90328SHEET 3 OF 4AS90328TABLE II.Copyright SAE International Provided by IHS

12、under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CABLE ASSEMBLYEXTERNAL ELECTRIC POWER,AIRCRAFT 115/200 VOLT, 400 HERTZAEROSPACE STANDARDAS90328SHEET 4 OF 4AS90328REQUIREMENTS:1. MATERIAL: SEE ACQUISITION SPECIFICATION.2. DIMENSIONS IN INCHES.

13、UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .025 (0.64MM).3. MOLDED-ON PLUGS, WHEN USED, SHALL MEET ALL THE REQUIREMENTS OF MS25486 EXCEPT THEY SHALLBE MOLDED TO THE CABLES.4. THE LAST IDENTIFIER OF THE CABLE ASSEMBLY PART NUMBER SHALL BE “A” TO INDICATE AN ATTACHABLEPLUG OR “M” TO INDICATE AN

14、INTEGRALLY MOLDED PLUG.5. CABLE ASSEMBLIES WHICH ARE ACQUIRED FOR AIR FORCE ORIGINAL APPLICATION, SHALL ONLY BEINTEGRALLY MOLDED CABLE ASSEMBLIES.6. AIR FORCE USE OF ATTACHABLE PLUGS SHALL BE LIMITED TO REPLACEMENT OF ORIGINAL MOLDEDASSEMBLY PLUGS DAMAGED IN SERVICE.7. SPLICE CRIMP BARRELS SHALL BE

15、CRIMP TYPE. MOLD OR STAMP WIRE SIZE ON CRIMP BARREL (TABLE II). SPLICE CRIMP BARREL SHALL BE COPPER OR COPPER ALLOY.8. TERMINAL LUGS CONNECTED TO A, B, C, AND N SOCKETS SHALL BE OF THE SIZE LISTED IN TABLE I ANDWIRE CONNECTED TO SOCKETS E AND F SHALL BE #12 AWG.9. MIL-I-23053 HEAT SHRINK INSULATION

16、TUBING WITH ADHESIVE ON THE I.D. SHALL BE PROVIDED BYSUPPLIER OF SPLICE-ON REPLACEMENT PLUGS. THE TUBING SHALL BE USED TO INSULATE THE CRIMPBARRELS AFTER FIELD INSTALLATION.10. INSTALLATION INSTRUCTIONS MUST BE INCLUDED WITH EACH SPLICE-ON REPLACEMENT PLUG.11. MOLDED REPLACEMENT PLUGS MS90328-39 AND

17、 -40 WITHOUT CONTROL LEADS SHALL HAVE SOCKETS “E”AND “F” CONNECTED TOGETHER WITHIN THE MOLDED PLUG BY A COPPER JUMPER WITH A CROSS-SECTIONAL AREA OF AT LEAST 6530 CIRCULAR MILS.FOR DESIGN FEATURE PURPOSES, THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER ACQUISITION DOCUMENTS REFERENCED HEREIN. REFERE

18、NCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATIONS FOR BID.CERTAIN PROVISIONS OF THIS SPECIFICATION SHEET ARE THE SUBJECT OF INTERNATIONAL STANDARDIZATION AGREEMENT ASCC AIR STANDARD 12/7, 12/12, STANAG 3303 AND 3457. WHEN AMENDMENT, REVISION, OR CANCELLATION OF THIS SPECIFICATION

19、 SHEET IS PROPOSED WHICH WILL AFFECT OR VIOLATE THE INTERNATIONAL AGREEMENT CONCERNED, THE PREPARING ACTIVITY WILL TAKE APPROPRIATE RECONCILIATION ACTION THROUGH INTERNATIONAL STANDARDIZATION CHANNELS INCLUDING DEPARTMENTAL STANDARDIZATION OFFICES, IF REQUIRED.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-