SAE AS 91101C-2017 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD CLOSE TOLERANCE SHANK UNS S66286 130 KSI MIN 1900-32 UNJF-3A.pdf

1、 AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, UNS S66286, 130 KSI MIN, .1900-32 UNJF-3A AS91101Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any fo

2、rm or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: htt

3、p:/www.sae.org ISSUED1999-12REVISED2017-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.C FEDERAL SUPPLY CLASS 5306 AS91101 SHEET 1 OF 2 REV. C PROCUREMENT SPECIFICATION: AS7477 SAE Technical Standards Board Rules SURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLQHHULQJVFLHQFHV7KH

4、XVHRIWKLVUHport is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingWKHUHIURPLVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancel

5、led. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS91101C RATIONALE DELETE .015 MINIMUM RADIUS AT TRANSITION OF WRENCH PAD TO BASE FLANGE, DELETE CIRCLED S SYMBOL (REGARDLESS OF FEATURE SI

6、ZE) FROM STRAIGHTNESS FCF, AND ADD NEW NOTE FOR USE OF EXISTING INVENTORY. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9110, NOTICE 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIR

7、EMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPLS) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - BOLT AEROSPACE STANDARD AS91101 SHEET 2 OF 2 REV. C BOLT, MACHINE

8、- DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, UNS S66286, 130 KSI MIN, .1900-32 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PART NO G GRIP L LENGTH K MAX APPROX MASS LB/100 PART NO G GRIP L LENGTH K MAX APPROX MASS LB/100 MS9110-16 .865- .885 1.396-1.416 .948 1.49 MS9110-02 .115-.1

9、35 .521- .541 .198 .80 MS9110-17 .927- .947 1.459-1.479 1.010 1.54 MS9110-03 .115-.135 .584- .604 .198 .84 MS9110-18 .990-1.010 1.521-1.541 1.072 1.59 MS9110-04 .115-.135 .646- .666 .198 .88 MS9110-19 1.115-1.135 1.646-1.666 1.198 1.70 MS9110-05 .178-.198 .709- .729 .260 .94 MS9110-20 1.240-1.260 1.

10、771-1.791 1.322 1.80 MS9110-06 .240-.260 .771- .791 .322 .99 MS9110-21 1.365-1.385 1.896-1.916 1.448 1.90 MS9110-07 .302-.322 .834- .854 .384 1.04 MS9110-22 1.490-1.510 2.021-2.041 1.573 2.00 MS9110-08 .365-.385 .896- .916 .448 1.09 MS9110-23 1.615-1.635 2.146-2.166 1.698 2.10 MS9110-09 .427-.447 .9

11、59- .979 .510 1.14 MS9110-24 1.740-1.760 2.271-2.291 1.823 2.20 MS9110-10 .490-.510 1.021-1.041 .572 1.19 MS9110-25 1.865-1.885 2.396-2.416 1.948 2.30 MS9110-11 .552-.572 1.084-1.104 .635 1.24 MS9110-26 1.990-2.010 2.521-2.541 2.072 2.40 MS9110-12 .615-.635 1.146-1.166 .698 1.29 MS9110-13 .678-.698

12、1.209-1.229 .760 1.34 MS9110-14 .740-.760 1.271-1.291 .823 1.39 MS9110-15 .802-.822 1.334-1.354 .885 1.44 NOTES 1. MATERIAL: CORROSION AND HEAT RESISTANT STEEL AMS5731 (UNS S66286). 2. PROCUREMENT SPECIFICATION: AS7477. 3. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLES

13、S OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MINIMUM. 5. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 6. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 7. DIMENSI

14、ONS ARE IN INCHES. 8. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN

15、IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.