SAE AS 9361B-2013 NUT PLAIN HEXAGON CHECK UNS S66286 130 KSI MIN《最小值为130 ksi六角平头螺母UNS S66286》.pdf

1、AEROSPACE STANDARD NUT, PLAIN, HEXAGON, CHECK, UNS S66286 130 KSI MIN AS9361Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording,

2、or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1999-04REAFFIRMED 2007-06 REVISED 2013-07THIRD

3、ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5310 AS9361SHEET 1 OF 2REV. BSAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitab

4、ility forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE value

5、s your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9361BRATIONALE REVISE THREAD SPECIFICATION TO AS8879, UPDATE FPI REQUIREMENTS, AND EDITORIAL UPDATE. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITA

6、RY STANDARD MS9361C. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR TH

7、IS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - NUT AEROSPACE STANDARD AS9361SHEET 2 OF 2REV. BNUT, PLAIN, HEXAGON, CHECK, UNS S66286 130 KSI MIN TABLE 1 - PART NUMBERS AND DIMENSIONS PARTNUMBER DTHREAD AF EMIN AB K LMINAPPROX. MASSLB/100 MS9361-08 .1640-36 UNJF-3B .336- .345 .374 .164

8、- .194 .099-.119 .334 .26 MS9361-09 .1900-32 UNJF-3B .367- .376 .410 .190- .220 .115-.135 .365 .36 MS9361-10 .2500-28 UNJF-3B .429- .439 .480 .250- .280 .115-.135 .428 .45 MS9361-11 .3125-24 UNJF-3B .492- .502 .552 .312- .342 .146-.166 .490 .68 MS9361-12 .3750-24 UNJF-3B .554- .564 .623 .375- .405 .

9、178-.198 .552 .96 MS9361-13 .4375-20 UNJF-3B .678- .690 .765 .438- .468 .209-.229 .678 1.76 MS9361-14 .5000-20 UNJF-3B .741- .752 .836 .500- .535 .240-.260 .740 2.25 MS9361-15 .5625-18 UNJF-3B .865- .877 .978 .562- .597 .271-.291 .865 3.57 MS9361-16 .6250-18 UNJF-3B .928- .940 1.050 .625- .660 .302-

10、.322 .928 4.36 MS9361-17 .7500-16 UNJF-3B 1.052-1.064 1.191 .750- .785 .365-.385 1.052 6.22 MS9361-18 .8750-14 UNJF-3B 1.239-1.252 1.405 .875- .910 .428-.448 1.240 10.17 MS9361-19 1.0000-12 UNJF-3B 1.427-1.440 1.619 1.000-1.035 .490-.510 1.428 15.51 NOTES: 1. MATERIAL: CORROSION AND HEAT RESISTANT S

11、TEEL AMS5732 OR AMS5737 (UNS S66286). 2. CLEANING: FINISHED PARTS SHALL BE DEGREASED AND IMMERSED FOR NOT LESS THAN 20 MINUTES IN A SOLUTION OF 1 VOLUME OF NITRIC ACID (SP GR 1.42) AND 9 VOLUMES OF WATER AT ROOM TEMPERATURE. 3. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1.

12、UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN AND AS5447. 5. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 6. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). /7/

13、MARKING: MARK PART NUMBER AND MANUFACTURERS IDENTIFICATION IN ACCORDANCE WITIH AS478, CLASS C. MULTIPLE MARKING OF BAR STOCK PERMISSIBLE PROVIDED POSITIVE IDENTIFICATION IS SHOWN. PARTS SHALL BE MARKED BEFORE THREADING. DASH NUMBERS MAY APPEAR ON ADJACENT FLATS. 8. DIMENSIONS ARE IN INCHES. 9. DO NO

14、T USE UNASSIGNED PART NUMBERS. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COM

15、PLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.