SAE AS 965B-1993 Drive-Studded Accessory (203 2) 8 000 BC Round Design Standard For《(203 2)8 000 BC圆形配件驱动枢的设计标准》.pdf

1、 AEROSPACE STANDARD DRIVE-STUDDED, ACCESSORY. (203.2) 8.000 BC ROUND, DESIGN STANDARD FOR AS965 Copyright 2004 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photo

2、copying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1967-10REVISED 1993-08 REAFFIRMED 2004

3、-03 THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-1 REV. B FEDERAL SUPPLY CLASSAS965 SHEET 1 OF 2 REV.B FIGURE 1 AEROSPACE STANDARD DRIVE-STUDDED, ACCESSORY. (203.2) 8.000 BC ROUND, DESIGN STANDARD FOR AS965 REV. B AS965 SHEET 2 OF 2 REV.B TABLE 1 DASH NO. SPLINE SIZE PD 1 2 3 (20.320) 0.800 (30.480) 1.2

4、00 (41.275) 1.625 NOTES: 1. OPERATING SPEEDS AND TORQUES, SHAFT TORSIONAL STRENGTH, AND ACCESSORY WEIGHT AND OVERHUNG MOMENT CAPACITIES SHALL BE SPECIFIED IN THE APPLICABLE POWER SOURCE MODEL SPECIFICATION OR BY THE PROCURING AGENCY. 2. SEE AIR1160 FOR INFORMATION RELATIVE TO THE APPLICATION OF THIS

5、 STANDARD. 3. DRIVE SHAFT: DETAILS OF DRIVE SHAFT AND SPLINE DESIGN DATA ARE SHOWN ON AS972. TRUE POSITION AND PERPENDICULARITY OF SPLINE SHALL BE MAINTAINED THROUGH 360E OF ROTATION. 4. LUBRICATION: SPLINE LUBRICATION SHALL BE PROVIDED. METHOD OF LUBRICATION SHALL BE SPECIFIED IN THE APPLICABLE POW

6、ER SOURCE MODEL SPECIFICATION OR BY THE PROCURING AGENCY. 5. OIL LEAKAGE: OIL LEAKAGE OUT OF THE DRIVE SHALL NOT EXCEED .003 L PER HOUR. PROVISIONS FOR DRAINING OIL FROM THE DRIVE CAVITY SHALL BE SUPPLIED. 6. ACCESSORY SPACE: SPACE AVAILABLE FOR ACCESSORIES SHALL BE SHOWN ON THE POWER SOURCE INSTALL

7、ATION DRAWING. 7. DIMENSIONS: ALL LINEAR DIMENSIONS ARE IN (MILLIMETERS) INCHES. DIMENSIONS AND TOLERANCES: ANSI Y14.5-1982. TRUE POSITION TOLERANCES ARE MAXIMUM MATERIAL CONDITION UNLESS OTHERWISE SPECIFIED. 8. TOLERANCES: LINEAR (+0.25) +.010, ANGULAR +2E UNLESS OTHERWISE SPECIFIED. 9. BREAK SHARP

8、 EDGES (0.08 TO 0.38) .003 TO .015 UNLESS OTHERWISE SPECIFIED. 10. FINISH: SURFACE TEXTURE PER ANSI/ASME B46.1 11. MATING FLANGE: SEE AS966 FOR DETAILS OF MATING ACCESSORY FLANGE. 12. STUDS: THREADED HOLES IN LIEU OF STUDS MAY BE PROVIDED WHEN SPECIFIED IN THE APPLICABLE MODEL SPECIFICATION. 13. DESIGNATION: THE AS NUMBER WITH DASH NUMBER DEFINES THE CONFIGURATION OF THE DRIVE. EXAMPLE: AS965 - 2 IS A (203.200) 8.000 BC ROUND QAD DRIVE WITH A (30.480) 1.200 P.D. OUTPUT SPLINE. 14. REFERENCE DOCUMENTS ARE THOSE IN EFFECT ON THE DATE OF ISSUANCE OF THIS DOCUMENT.