SAE AS 9676B-2014 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK CUP WASHER LOCKED CRES UNS S66286 130 KSI MIN 1900-32 UNJF-3A《 1900-32 UNJF-3A、最小130 KSI、UNS S66286、CR.pdf

1、AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CUP WASHER LOCKED,CRES, UNS S66286, 130 KSI MIN, .1900-32 UNJF-3AAS9676Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, i

2、n any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDR

3、ESS: http:/www.sae.org ISSUED 1999-08REAFFIRMED2007-06REVISED 2014-07THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5306 AS9676SHEET 1 OF 2REV. BPROCUREMENT SPECIFICATION: AS7477SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of t

4、echnicalandengineeringsciences.The useofthis reportisentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay be

5、revised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9676BRATIONALE REVISE WRENCHING ELEMENT RUNOUT CALLOUT (RELOCATE FROM WRENCH FLATS TO

6、POINTS), REVISE LIGHTENING HOLE CONFIGURATION (REVISE SECTION VIEW) TO ALLOW OPTIONAL SHAPE AT BOTTOM OF HOLE. DELETE RADIUS AT TRANSITION OF WRENCH FLATS AND BASE FLANGE, UPDATE REFERENCES. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9676, AM

7、ENDMENT 1, NOTICE 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR TH

8、IS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - BOLT AEROSPACE STANDARD AS9676SHEET 2 OF 2REV. BBOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CUP WASHER LOCKED, CRES, UNS S66286, 130 KSI MIN, .1900-32 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PARTNUMBER L K APPROX.

9、 MASSLB/100 PARTNUMBER L K APPROX. MASSLB/100 MS9676-03 .302- .322 .072-.092 .90 MS9676-24 1.615-1.635 .935- .995 1.77 MS9676-04 .365- .385 .072-.092 .96 MS9676-25 1.678-1.698 .998-1.058 1.81 MS9676-05 .428- .448 .072-.092 1.00 MS9676-26 1.740-1.760 1.060-1.120 1.85 MS9676-06 .490- .510 .072-.092 1.

10、04 MS9676-27 1.865-1.885 1.185-1.245 1.93 MS9676-07 .552- .572 .072-.092 1.08 MS9676-28 1.990-2.010 1.310-1.370 2.01 MS9676-08 .615- .635 .072-.092 1.12 MS9676-29 2.115-2.135 1.435-1.495 2.09 MS9676-09 .678- .698 .072-.092 1.16 MS9676-30 2.240-2.260 1.560-1.620 2.17 MS9676-10 .740- .760 .072-.120 1.

11、20 MS9676-31 2.365-2.385 1.685-1.745 2.25 MS9676-11 .802- .822 .122-.182 1.24 MS9676-32 2.490-2.510 1.810-1.870 2.33 MS9676-12 .865- .885 .185-.245 1.28 MS9676-33 2.615-2.635 1.935-1.995 2.42 MS9676-13 .928- .948 .248-.308 1.32 MS9676-34 2.740-2.760 2.060-2.120 2.50 MS9676-14 .990-1.010 .310-.370 1.

12、36 MS9676-35 2.865-2.885 2.185-2.245 2.58 MS9676-15 1.052-1.072 .372-.432 1.40 MS9676-36 2.990-3.010 2.310-2.370 2.66 MS9676-16 1.115-1.135 .435-.495 1.45 MS9676-37 3.115-3.135 2.435-2.495 2.74 MS9676-17 1.178-1.198 .498-.558 1.49 MS9676-38 3.240-3.260 2.560-2.620 2.82 MS9676-18 1.240-1.260 .560-.62

13、0 1.53 MS9676-39 3.365-3.385 2.685-2.745 2.90 MS9676-19 1.302-1.322 .622-.682 1.57 MS9676-40 3.490-3.510 2.810-2.870 2.98 MS9676-20 1.365-1.385 .685-.745 1.61 MS9676-41 3.615-3.635 2.935-2.995 3.06 MS9676-21 1.428-1.448 .748-.808 1.65 MS9676-42 3.740-3.760 3.060-3.120 3.14 MS9676-22 1.490-1.510 .810

14、-.870 1.69 MS9676-43 3.865-3.885 3.185-3.245 3.22 MS9676-23 1.552-1.572 .872-.932 1.73 NOTES: /1/ FOR PART NUMBERS MS9676-03 THRU MS9676-13 DATUM Z SHALL REPLACE DATUM Y.2. MATERIAL: CORROSION AND HEAT RESISTANT STEEL PER AMS5731 (UNS S66286). 3. PROCUREMENT SPECIFICATION: AS7477 4. FLUORESCENT PENE

15、TRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS ARE IN INCHE

16、S. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISS

17、UE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.