SAE AS 9687B-2016 BOLT MACHINE C HEXAGON HEAD DRILLED 1 HOLE PD SHANK STEEL UNS K14675 DIFFUSED NICKELCADMIUM PLATE 195 KSI MIN 3125-24 UNJF-3A.pdf

1、AEROSPACE STANDARDBOLT, MACHINE HEXAGON HEAD, DRILLED, 1 HOLE,PD SHANK, STEEL, UNS K14675, DIFFUSED NICKEL-CADMIUM PLATE, 195 KSI MIN, .3125-24 UNJF-3AAS9687Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted

2、, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADD

3、RESS: http:/www.sae.orgISSUED1998-08 REAFFIRMED2007-06 REVISED2016-06THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.BFEDERAL SUPPLY CLASS5306AS9687SHEET 1 OF 3REV.BPROCUREMENT SPECIFICATION: AS7459SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengin

4、eering sciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,sta

5、bilized,orcancelled.SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9687BRATIONALEREVISE THREAD SPECIFICATION TO AS8879, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING, UPDATE MAGNET

6、IC PARTICLE INSPECTION REFERENCE, ADD DATUM W, DATUM U, AND POSITIONAL REQUIREMENTS FOR DRILLED HOLE, ADD NEW EXISTING INVENTORY USE NOTE, UPDATE ANSI Y14.5M-1983 SYMBOLS, UPDATE CADMIUM NOTICE, AND GENERAL EDITORIAL REVISION.NOTICETHE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM

7、 U.S. MILITARY STANDARD MS9687, NOTICE 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT.ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED

8、BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT.FIGURE 1 - BOLTAEROSPACE STANDARDAS9687SHEET 2 OF 3REV.BBOLT, MACHINE HEXAGON HEAD, DRILLED, 1 HOLE,PD SHANK, STEEL, UNS K14675, DIFFUSED NICKEL-CADMIUM PLATE, 195 KSI MIN, .3125-24 UNJF-3ATABLE 1 PART NUMBERS AND DIMENSIONSPART NO.

9、L KAPPROX.MASSLB/100 PART NO. L KAPPROX.MASSLB/100MS9687-04MS9687-05MS9687-06.490 - .510.552 - .572.615 - .635.088 - .108.088 - .108.088 - .1082.122.232.34MS9687-34MS9687-35MS9687-362.740 - 2.7602.865 - 2.8852.990 - 3.0101.815 - 1.8751.940 - 2.0002.065 - 2.1256.176.406.62MS9687-07MS9687-08MS9687-09.

10、678 - .698.740 - .760.802 - .822.088 - .108.088 - .108.088 - .1082.452.562.67MS9687-37MS9687-38MS9687-393.115 - 3.1353.240 - 3.2603.365 - 3.3852.190 - 2.2502.315 - 2.3752.440 - 2.5006.857.087.30MS9687-10MS9687-11MS9687-12.865 - .885.928 - .948.990 - 1.010.088 - .108.088 - .108.088 - .1252.792.903.01

11、MS9687-40MS9687-41MS9687-423.490 - 3.5103.615 - 3.6353.740 - 3.7602.565 - 2.6252.690 - 2.7502.815 - 2.8757.537.757.98MS9687-13MS9687-14MS9687-151.052 - 1.0721.115 - 1.1351.178 - 1.198.128 - .188.190 - .250.252 - .3123.133.243.35MS9687-43MS9687-44MS9687-453.865 - 3.8853.990 - 4.0104.115 - 4.1352.940

12、- 3.0003.065 - 3.1253.190 - 3.2508.208.438.66MS9687-16MS9687-17MS9687-181.240 - 1.2601.302 - 1.3221.365 - 1.385.315 - .375.375 - .438.440 - .5003.463.583.69MS9687-46MS9687-47MS9687-484.240 - 4.2604.365 - 4.3854.490 - 4.5103.315 - 3.3753.440 - 3.5003.565 - 3.6258.889.119.33MS9687-19MS9687-20MS9687-21

13、1.428 - 1.4481.490 - 1.5101.552 - 1.572.502 - .562.565 - .625.628 - .6883.803.924.03MS9687-49MS9687-50MS9687-514.615 4.6354.740 - 4.7604.865 - 4.8853.690 - 3.7503.815 - 3.8753.940 - 4.0009.569.7810.01MS9687-22MS9687-23MS9687-241.615 - 1.6351.678 - 1.6981.740 - 1.760.690 - .750.752 - .812.815 - .8754

14、.144.254.37MS9687-52MS9687-53MS9687-544.990 - 5.0105.115 - 5.1355.240 - 5.2604.065 - 4.1254.190 - 4.2504.315 - 4.37510.2410.4610.69MS9687-25MS9687-26MS9687-271.802 - 1.8221.865 - 1.8851.928 - 1.948.878 - .938.940 - 1.0001.002 - 1.0624.484.594.71MS9687-55MS9687-56MS9687-575.365 - 5.3855.490 - 5.5105.

15、615 - 5.6354.440 - 4.5004.565 - 4.6254.690 - 4.75010.9111.1411.36MS9687-28MS9687-29MS9687-301.990 - 2.0102.115 - 2.1352.240 - 2.2601.065 - 1.1251.190 - 1.2501.315 - 1.3754.825.045.27MS9687-58MS9687-59MS9687-605.740 - 5.7605.865 - 5.8855.990 - 6.0104.815 - 4.8754.940 - 5.0005.065 - 5.12511.5911.8112.

16、04MS9687-31MS9687-32MS9687-332.365 - 2.3852.490 - 2.5102.615 - 2.6351.440 - 1.5001.565 - 1.6251.690 - 1.7505.505.725.95NOTICETHIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE.NOTES:/1/ FOR PART NUMBERS

17、MS9687-04 THROUGH MS9687-19 DATUM Z SHALL REPLACE DATUM Y.2. MATERIAL LOW ALLOY STEEL AMS6304 (UNS K14675).3. PROCUREMENT SPECIFICATION: AS7459.4. FINISH: DIFFUSED NICKEL-CADMIUM PLATE AMS2416. DIMENSIONS APPLY AFTER PLATING. CONTACT POINTS PERMISSIBLE. PD MAY BE REDUCED .0012 MAXIMUM BEFORE PLATING

18、.5. MAGNETIC PARTICLE INSPECTION PER ASTM E1444/E1444M BEFORE PLATING.6. INCOMPLETE THREADS NOT TO ENTER FILLET.7. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra.8. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE

19、 SPECIFIED.9. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION).AEROSPACE STANDARDAS9687SHEET 3 OF 3REV.BBOLT, MACHINE HEXAGON HEAD, DRILLED, 1 HOLE,PD SHANK, STEEL, UNS K14675, DIFFUSED NICKEL-CADMIUM PLATE, 195 KSI MIN, .3125-24 UNJF-3A10. DIMENSIONS IN INCHES.11. UNLESS OTHERWI

20、SE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED.11. DO NOT USE UNASSIGNED PART NUMBERS.12. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN

21、 LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.