SAE AS 9698C-2016 BOLT MACHINE C DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK CORROSION AND HEAT RESISTANT NICKEL ALLOY (UNS N07001) 165 KSI MIN 3125-24 UNJF-3A.pdf

1、AEROSPACE STANDARDBOLT, MACHINE DOUBLE HEXAGON EXTENDEDWASHER HEAD, PD SHANK, CORROSION AND HEATRESISTANT NICKEL ALLOY (UNS N07001), 165 KSI MIN, .3125-24 UNJF-3AAS9698Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or

2、transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org

3、SAE WEB ADDRESS: http:/www.sae.orgISSUED2003-09REVISED2016-08THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV.CFEDERAL SUPPLY CLASS5306AS9698SHEET 1 OF 3REV.CPROCUREMENT SPECIFICATION: AS7471SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering s

4、ciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,

5、orcancelled.SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9698CRATIONALEUPDATE STRAIGHTNESS CALLOUT, RELOCATE RUNOUT REQUIREMENT FROM ACROSS FLATS TO ACROSS POINTS, DELETE RADIUS

6、 REQUIREMENT AT BASE OF WRENCH PAD, REVISE FPI REQUIREMENTS, CLARIFY COLD ROLLING NOTE, ADD NOTE FOR USE OF EXISTING INVENTORY, UPDATE SURFACE TEXTURE SYMBOLS, UPDATE REFERENCES AND GENERAL EDITORIAL REVISION.NOTICETHE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY ST

7、ANDARDMS9698A. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT.ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPLS) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STA

8、NDARD AND ARE NOT PART OF THIS SAE DOCUMENT.FIGURE 1 - BOLTAEROSPACE STANDARDAS9698SHEET 2 OF 3REV.CBOLT, MACHINE DOUBLE HEXAGON EXTENDEDWASHER HEAD, PD SHANK, CORROSION AND HEATRESISTANT NICKEL ALLOY (UNS N07001), 165 KSI MIN, .3125-24 UNJF-3ATABLE 1 - PART NUMBERS AND DIMENSIONSPART NO. L KAPPROX.

9、MASSLB/100 PART NO. L KAPPROX.MASSLB/100MS9698-04MS9698-05MS9698-06.490- .510.552- .572.615- .635.088- .108.088- .108.088- .1082.172.292.41MS9698-32MS9698-33MS9698-342.615- 2.6352.740- 2.7602.865- 2.8851.690- 1.7501.815- 1.8751.940- 2.0006.196.426.66MS9698-07MS9698-08MS9698-09.678- .698.740- .760.80

10、2- .822.088- .108.088- .108.088- .1082.522.642.76MS9698-35MS9698-36MS9698-372.990- 3.0103.115- 3.1353.240- 3.2602.065- 2.1252.190- 2.2502.315- 2.3756.907.137.36MS9698-10MS9698-11MS9698-12.865- .885.928- .948.990- 1.010.088- .108.088- .108.088- .1252.883.003.11MS9698-38MS9698-39MS9698-403.365- 3.3853

11、.490- 3.5103.615- 3.6352.440- 2.5002.565- 2.6252.690- 2.7507.607.848.07MS9698-13MS9698-14MS9698-151.052- 1.0721.115- 1.1351.178- 1.198.128- .188.190- .250.252- .3123.233.353.47MS9698-41MS9698-42MS9698-433.740- 3.7603.865- 3.8853.990- 4.0102.815- 2.8752.940- 3.0003.065- 3.1258.318.548.78MS9698-16MS96

12、98-17MS9698-181.240- 1.2601.302- 1.3221.365- 1.385.315- .375.378- .438.440- .5003.593.703.82MS9698-44MS9698-45MS9698-464.115- 4.1354.240- 4.2604.365- 4.3853.190- 3.2503.315- 3.3753.440- 3.5009.029.259.49MS9698-19MS9698-20MS9698-211.428- 1.4481.490- 1.5101.552- 1.572.502- .562.565- .625.628- .6883.94

13、4.064.18MS9698-47MS9698-48MS9698-494.490- 4.5104.615- 4.6354.740- 4.7603.565- 3.6253.690- 3.7503.815- 3.8759.729.9610.20MS9698-22MS9698-23MS9698-241.615- 1.6351.678- 1.6981.740- 1.760.690- .750.752- .812.815- .8754.294.414.53MS9698-50MS9698-51MS9698-524.865- 4.8854.990- 5.0105.115- 5.1353.940- 4.000

14、4.065- 4.1254.190- 4.25010.4310.6710.91MS9698-25MS9698-26MS9698-271.802- 1.8221.865- 1.8851.990- 2.010.877- .938.940-1.0001.065-1.1254.654.775.00MS9698-53MS9698-54MS9698-555.240- 5.2605.365 -5.3855.490- 5.5104.315- 4.3754.440- 4.5004.565- 4.62511.1411.3811.61MS9698-28MS9698-29MS9698-302.115- 2.1352.

15、240- 2.2602.365- 2.3851.190-1.2501.315-1.3751.440-1.5005.245.485.71MS9698-56MS9698-57MS9698-585.615- 5.6355.740 -5.7605.865- 5.8854.690- 4.7504.815- 4.8754.940- 5.00011.8512.0912.32MS9698-31 2.490- 2.510 1.565-1.625 5.95 MS9698-59 5.990- 6.010 5.065- 5.125 12.56NOTES:/1/ FOR PART NUMBERS MS9698-04 T

16、HRU MS9698-14 DATUM Z SHALL REPLACE DATUM Y.2. MATERIAL: AMS5708 CORROSION AND HEAT RESISTANT NICKEL ALLOY (UNS N07001).3. PROCUREMENT SPECIFICATION: AS7471.4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN.5. EXCEPT PART NUMBERS MS9698-14 AND SMALLER, HEAD T

17、O SHANK FILLET SHALL BE COLD ROLLED. COLD ROLLING SHALL BE SUFFICIENT TO REMOVE ALL VISUAL EVIDENCE OF GRINDING OR TOOL MARKS.6. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra.7. BREAK SHARP EDGES .003 TO .015, UN

18、LESS OTHERWISE SPECIFIED.8. DIMENSIONS ARE IN INCHES.9. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION).10. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED.A

19、EROSPACE STANDARDAS9698SHEET 3 OF 3REV.CBOLT, MACHINE DOUBLE HEXAGON EXTENDEDWASHER HEAD, PD SHANK, CORROSION AND HEATRESISTANT NICKEL ALLOY (UNS N07001), 165 KSI MIN, .3125-24 UNJF-3A11. DO NOT USE UNASSIGNED PART NUMBERS.12. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR TH

20、E CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.