1、 AEROSPACE STANDARD BOLT, MACHINE-DOUBLE HEXAGON, EXTENDED WASHER HEAD, PD SHANK, CRES AMS5643, .2500-28 UNJF-3A AS9733Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electr
2、onic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1998-
3、11REAFFIRMED 2005-05REVISED2017-11THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.B FEDERAL SUPPLY CLASS 5306 AS9733 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS7474 SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering scien
4、ces. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed,
5、stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS9733B RATIONALE DELETE RADIUS AT TRANSITION OF WRENCH FLATS AND BASE FLANGE, ADD EXISTING INVENTORY DISPOSITION NOTE
6、, DELETE CURRENT NOTE 4 (HARDNESS REQUIREMENT) DELETE REGARDLESS OF FEATURE SIZE SYMBOL FROM STRAIGHTNESS FEATURE CONTROL FRAME, FIGURE 1 REDRAWN, GENERAL EDITORIAL UPDATE. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9733(ASG), AMENDMENT 1. TH
7、IS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPLS) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NO
8、T PART OF THIS SAE DOCUMENT. . 3 1 2 5N O M. 4 2 8. 4 4 8. 0 0 7 Y. 0 0 7 YM A R K P A R T N U M B E R A N DM A N U F A C T U R E R S I D E N T I F I C A T I O NP E R A S 4 7 8 C L A S S A E X C E P TE D G E D I S T A N C E R E Q U I R E M E N T S D O N O T A P P L YC H A M F E R 2 8 - 3 2 T O . 3 0
9、 2 - . 3 2 2. 1 4 4 M I N32W R E N C H I N G C O N F I G U R A T I O NP E R A S 8 7 0 - 1 0 F O R T H I S D I S T A N C E. 0 6 0 M I NKLR. 0 2 5. 0 1 5T H R E A D R U N O U TP E R A S 3 0 6 23 5 M I N T O R O O TO F D O U B L E H E X A G O N4 5 A P P R O X. 0 1 8 M I N. 2 0 4. 1 8 4. 2 9 3. 3 1 332.
10、 0 0 3 Y. 2 5 0 0 - 2 8 U N J F - 3 AP E R A S 8 8 7 9. 2 3 2Z . 0 0 3 / 1. 0 0 6 ZY. 1 5 8. 1 7 82 5 0. 1 6 0. 1 4 05 M A X . 3 9 8 M I NB E A R I N G S U R F A C ES H A P E A T B O T T O M O P T I O N A L. 1 2 9 M I NS E C T I O N T H R U H E A D32S E C T I O N T H R UT H R E A D P R O F I L E. 2
11、2 2/ 1 /2 5 02 5 0FIGURE 1 - BOLT AEROSPACE STANDARD AS9733 SHEET 2 OF 3 REV. B BOLT, MACHINE-DOUBLE HEXAGON, EXTENDED WASHER HEAD, PD SHANK, CRES AMS 5643, .2500-28 UNJF-3A TABLE 1 PART NUMBERS AND DIMENSIONS PART NO. L K APPROX MASS LB/100 PART NO. L K APPROX MASS LB/100 MS9733-04 .365-.385 .079-
12、.099 1.28 MS9733-34 2.615-2.635 1.815-1.875 3.83 MS9733-05 .428-.448 .079- .099 1.35 MS9733-35 2.740-2.760 1.940-2.000 3.97 MS9733-06 .490-.510 .079- .099 1.42 MS9733-36 2.865-2.885 2.065-2.125 4.12 MS9733-07 .552- .572 .079- .099 1.50 MS9733-37 2.990-3.010 2.190-2.250 4.26 MS9733-08 .615- .635 .079
13、- .099 1.57 MS9733-38 3.115-3.135 2.315-2.375 4.40 MS9733-09 .678- .698 .079- .099 1.64 MS9733-39 3.240-3.260 2.440-2.500 4.54 MS9733-10 .740- .760 .079- .099 1.71 MS9733-40 3.365-3.385 2.565-2.625 4.68 MS9733-11 .802- .822 .079- .099 1.78 MS9733-41 3.490-3.510 2.690-2.750 4.82 MS9733-12 .865- .885
14、.079- .125 1.85 MS9733-42 3.615-3.635 2.815-2.875 4.96 MS9733-13 .928- .948 .128- .188 1.92 MS9733-43 3.740-3.760 2.940-3.000 5.11 MS9733-14 .990-1.010 .190- .250 1.99 MS9733-44 3.865-3.885 3.065-3.125 5.25 MS9733-15 1.052-1.072 .252- .312 2.06 MS9733-45 3.990-4.010 3.190-3.250 5.39 MS9733-16 1.115-
15、1.135 .315- .375 2.13 MS9733-46 4.115-4.135 3.315-3.375 5.53 MS9733-17 1.178-1.198 .378- .438 2.20 MS9733-47 4.240-4.260 3.440-3.500 5.67 MS9733-18 1.240-1.260 .440- .500 2.27 MS9733-48 4.365-4.385 3.565-3.625 5.81 MS9733-19 1.302-1.322 .502- .562 2.34 MS9733-49 4.490-4.510 3.690-3.750 5.96 MS9733-2
16、0 1.365-1.385 .565- .625 2.42 MS9733-50 4.615-4.635 3.815-3.875 6.10 MS9733-21 1.428-1.448 .628- .688 2.49 MS9733-51 4.740-4.760 3.940-4.000 6.24 MS9733-22 1.490-1.510 .690- .750 2.56 MS9733-52 4.865-4.885 4.065-4.125 6.38 MS9733-23 1.552-1.572 .752- .812 2.63 MS9733-53 4.990-5.010 4.190-4.250 6.52
17、MS9733-24 1.615-1.635 .815- .875 2.70 MS9733-54 5.115-5.135 4.315-4.375 6.66 MS9733-25 1.678-1.698 .878- .938 2.77 MS9733-55 5.240-5.260 4.440-4.500 6.81 MS9733-26 1.740-1.760 .940-1.000 2.84 MS9733-56 5.365-5.385 4.565-4.625 6.95 MS9733-27 1.802-1.822 1.002-1.062 2.91 MS9733-57 5.490-5.510 4.690-4.
18、750 7.09 MS9733-28 1.865-1.885 1.065-1.125 2.98 MS9733-58 5.615-5.635 4.815-4.875 7.23 MS9733-29 1.990-2.010 1.190-1.250 3.12 MS9733-59 5.740-5.760 4.940-5.000 7.37 MS9733-30 2.115-2.135 1.315-1.375 3.27 MS9733-60 5.865-5.885 5.065-5.125 7.51 MS9733-31 2.240-2.260 1.440-1.500 3.41 MS9733-61 5.990-6.
19、010 5.190-5.250 7.66 MS9733-32 2.365-2.385 1.565-1.625 3.55 MS9733-33 2.490-2.510 1.690-1.750 3.69 NOTES /1/ FOR PART NUMBERS MS9733-04 THROUGH MS9733-16, THE THREAD PD (DATUM Z) SHALL REPLACE DATUM Y. 2. MATERIAL: CORROSION RESISTANT STEEL AMS5643 (UNS S17400). 3. PROCUREMENT SPECIFICATION: AS7474.
20、 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MINIMUM. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36. REQUIREMENTS PER ASME B46.1M. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. AEROSPACE STANDARD AS9733 SHEET 3 OF 3 REV. B BOLT, MACHINE-DOUBL
21、E HEXAGON, EXTENDED WASHER HEAD, PD SHANK, CRES AMS 5643, .2500-28 UNJF-3A 6. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982. (ASME PUBLICATION). 7. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 8. DIMENSIONS ARE IN INCHES. 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. UNLESS OTHERWISE
22、 SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED 11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS
23、, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1