SAE AS 9894A-2015 Bolt Machine-Double Hexagon Extended Washer Head Drilled AMS 5616 190-32 UNJF-3A.pdf

1、 AEROSPACE STANDARD BOLT, MACHINE-DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, AMS5616, .190-32 UNJF-3AAS9894Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mec

2、hanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1999-05REAFFI

3、RMED2005-05REVISED 2015-03THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.A FEDERAL SUPPLY CLASS 5306AS9894 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: AS7470SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse

4、 ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcan

5、celled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9894A RATIONALE FIGURE REVISED , THREAD SPEC REVISED, TABLES REDRAWN AND NOTES REVISED TO UPDATE SPECS. NOTICE THE INITIAL

6、SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9894 (ASG), NOTICE 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR D

7、OD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. .250 NOMWRENCHING PAD CONFIGURATIONAS870-08 FOR THIS DISTANCE.122 MIN.040 MIN.365.385.006 Y.006 YMARK PART NUMBER AND MANUFACTURERS IDENTIFICATIONPER AS478 CLASS A EX

8、CEPTEDGE DISTANCE REQUIREMENTS DO NOT APPLYCHAMFER 28- 32TO .240 - .260250324035LKTHREADRUNOUTPER AS3062.021 -.041 x 45APPROXR.015.025.1900-32 UNJF-3APER AS8879.175.165.003/1.006 A.335 MINBEARING SURFACESECTION THRUTHREAD PROFILE322505 MAX.100 MINSECTION THRU HEADSHAPE OPTIONALIN THIS AREA.003 Y32CH

9、AMFER250.110.090.120.140.1874 x 45W4 x .042 -.052CSK 85 - 95 TO .060 -.070.015 U W.268.248UYAYFIGURE 1 AEROSPACE STANDARD AS9894 SHEET 2 OF 2 REV. A BOLT, MACHINE-DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, AMS5616, .190-32 UNJF-3A TABLE 1 PART NUMBER L K APPROX MASS LB/100 PART NUMBER L K APPROX

10、MASS LB/100 MS9894-03 .312 .072 - .092 .69 MS9894-26 1.750 1.060 - 1.120 1.61 MS9894-04 .375 .072 - .092 .73 MS9894-27 1.812 1.122 - 1.182 1.65 MS9894-05 .438 .072 - .092 .76 MS9894-28 1.875 1.185 - 1.245 1.69 MS9894-06 .500 .072 - .092 .80 MS9894-29 1.938 1.248 - 1.308 1.73 MS9894-07 .582 .072 - .0

11、92 .84 MS9894-30 2.000 1.310 - 1.370 1.77 MS9894-08 .625 .072 - .092 .88 MS9894-31 2.125 1.435 - 1.495 1.85 MS9894-09 .688 .072 - .092 .92 MS9894-32 2.250 1.560 - 1.620 1.93 MS9894-10 .750 .072 - .120 .96 MS9894-33 2.375 1.685 - 1.745 2.01 MS9894-11 .812 .122 - .182 1.00 MS9894-34 2.500 1.810 - 1.87

12、0 2.09 MS9894-12 .875 .185 - .245 1.04 MS9894-35 2.625 1.935 - 1.995 2.17 MS9894-13 .938 .248 - .308 1.09 MS9894-36 2.750 2.060 - 2.120 2.25 MS9894-14 1.000 .310 - .370 1.13 MS9894-37 2.875 2.185 - 2.245 2.33 MS9894-15 1.062 .372 - .432 1.17 MS9894-38 3.000 2.310 - 2.370 2.41 MS9894-16 1.125 .435 -

13、.495 1.21 MS9894-39 3.125 2.435 - 2.495 2.49 MS9894-17 1.188 .498 - .558 1.25 MS9894-40 3.250 2.560 - 2.620 2.57 MS9894-18 1.250 .560 - .620 1.29 MS9894-41 3.375 2.685 - 2.745 2.65 MS9894-19 1.312 .622 - .682 1.33 MS9894-42 3.500 2.810 - 2.870 2.73 MS9894-20 1.375 .685 - .745 1.37 MS9894-43 3.625 2.

14、935 - 2.995 2.81 MS9894-21 1.438 .748- .808 1.41 MS9894-44 3.750 3.060 - 3.120 2.89 MS9894-22 1.500 .810 - .870 1.45 MS9894-45 3.875 3.185 - 3.245 2.97 MS9894-23 1.562 .872 - .932 1.49 MS9894-24 1.625 .935 - .995 1.53 MS9894-25 1.688 .998 - 1.058 1.57 NOTES: 1. MATERIAL: CORROSION RESISTANT STEEL AM

15、S5616. 2. MANUFACTURING SPECIFICATION: AS7470 EXCEPT HEAD SHALL BE UPSET. 3. HEAD TO SHANK FILLET SHALL BE COLD ROLLED AFTER HEAT TREATMENT TO REMOVE ALL VISUAL EVIDENCE OF GRINDING OR TOOL MARKS. 4. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED,

16、SURFACES TO BE 125 MICROINCHES Ra. EXCEPT UPSET HEAD. 5. MAGNETIC PARTICLE INSPECTION PER ASTM E1444. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 5. 8 DO NOT USE UNASSIGNED P

17、ART NUMBERS. 9. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF T

18、HE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION. .