SAE EIA-591-1992 Assessment of Quality Levels in PPM Using Variables Test Data (Formerly TechAmerica EIA-591).pdf

1、 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/EIA591 TECHNICAL REPORT EIA-591 Issued 1992-12 Assessment of Quality Levels in PP

5、M Using Variables Test Data NOTICE This document has been taken directly from the original TechAmerica document and contains only minor editorial and format changes required to bring it into conformance with the publishing requirements of SAE Technical Standards. The release of this document is inte

6、nded to replace the original with the SAE International document. Any numbers established by the original document remain unchanged. The original document was adopted as an SAE publication under the provisions of the SAE Technical Standards Board (TSB) Rules and Regulations (TSB 001) pertaining to a

7、ccelerated adoption of specifications and standards. TSB rules provide for (a) the publication of portions of unrevised specifications and standards without consensus voting at the SAE committee level, and (b) the use of the existing specification or standard format. TechAmerica Standard Assessment

8、of Quality Levels in PPM Using Variables Test Data EIA-591 December 1992 EIA-591NOTICE TechAmerica Engineering Standards and Publications are designed to serve the public interest by eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement o

9、f products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of TechAmerica from manufacturing or selling products not conformin

10、g to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than TechAmerica members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by TechAmerica in a

11、ccordance with the American National Standards Institute (ANSI) patent policy. By such action, TechAmerica does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This TechAmerica Standard is considered to have In

12、ternational Standardization implications, but the ISO/IEC activity has not progressed to the point where a valid comparison between the TechAmerica Standard and the ISO/IEC document can be made. This Standard does not purport to address all safety problems associated with its use or all applicable r

13、egulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 4963; formulated under the cognizance of the Quality and Reliab

14、ility Engineering (QRE) Committee). Published by 2011 TechAmerica Standards & Technology Department 601 Pennsylvania Ave., NW North Building, Suite 600 Washington, DC 20004-2650 All rights reserved - Printed in U.S.A. PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by TechAmerica and may

15、not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies by entering into a license agreement with our distributors. For distributor information please see our web site www. techamerica.org/ or contact TechAmerica at 703-284-5355 TechAmerica Assessment of Quality Levels in PPM Using Variables Test Data EIA-591 Revision Description of change Date - Initial Release Dec 1992