SAE J 1147-1983 Welding Brazing and Soldering - Materials and Practices Information Report《铜焊和钎焊材料和规程》.pdf

1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefro

2、m, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243TO PLACE A DOCUMENT

3、 ORDER; (724) 776-4970 FAX: (724) 776-0790SAE WEB ADDRESS http:/www.sae.orgCopyright 1983 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.S.A.SURFACEVEHICLE400 Commonwealth Drive, Warrendale, PA 15096-0001INFORMATIONREPORTJ1147REV.JUN83Issued 1976-07Revised 1983-06Superseding

4、J1147 JUL76WELDING, BRAZING, AND SOLDERINGMATERIALS AND PRACTICESForewordThis Document has also changed to comply with the new SAE Technical Standards Board Format.1. ScopeThe Joint AWS/SAE Committee on Automotive Welding was organized on January 16, 1974, for theprimary purpose of facilitating the

5、development and publication of various documents related to the selection,specification, testing, and use of welding materials and practices, particularly for the automotive and relatedindustries. A secondary purpose is the dissemination of technical information.1.1 SAE participation in this activit

6、y is intended to insure that the needs and thinking of the industries mentionedare adequately considered prior to publication of selected Standards, Recommended Practices, andInformation Reports. To this end, such documents are subject to the approval of the SAE General MaterialsCouncil, as well as

7、the Joint AWS/SAE Committee and the AWS Board of Directions.1.2 Docuemnts which are approved by the Council are printed as separate sheets or booklets, with both AWS Dnumber and SAE HS J number identifications. They are not published in the SAE Handbook. SAE numbereditems approved to date for listin

8、g in this Information Report are:a. SAE HS J1156 (AWS D8.6-77Automotive Resistance Spot Welding Electrods. THis documentrecommends a “standard” for spot welding electrodes sutiable foruse by smaller suppliers to theautomotive industry. Typical electrode cap “standards” of the major autombile manufac

9、turers areincluded for information purposes.b. SAE HS J1188 (AWS D8.7-78)Specification for Automotive Weld QualityResistance SpotWelding.c. SAE HS J1196 (AWS D8.8-79)Specification for Automotive Frame Weld QualityArc Welding.1.3 The SAE Metal Joining Subcommittee (disbanded prior to organization of

10、the Joint AWS/SAE Committee onAutomotive Welding) developed the following document. This, also, is published only as a handbooksupplement.a. SAE HS J836Automotive Metallurgical Joining. This document is an abbreviated summary ofmetallurgical joining, brazing, and soldering, intended to reflect usage

11、 in the automotive industry.SAE J1147 Revised JUN83-2-2. References2.1 Applicable PublicationsThe following publications form a part of the specification to the extent specifiedherein. Unless otherwise indicated the latest revision of SAE publications shall apply.2.1.1 SAE PUBLICATIONSAvailable from

12、 SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.SAEHSJ836Automotive Metallurgical Joining.SAE HS J1156 (AWS D8.6-77)Automotive Resistance Spot Welding Electrodes.SAE HS J1188 (AWS D8.7-78)Specification for Automotive Weld QualityResistance Spot Welding.SAE HS J1198 (AWS D8.7-79)Specification

13、 for Automotive Frame Weld QualityArc Welding.2.1.2 AWS PUBLICATIONSAvailable from American Welding Society, 550 LeJeune Road, Miami, FL 33126.SAE AWS D8.6-77Automotive Resistance Spot Welding Electrodes.SAE AWS D8.7-78Specification for Automotive Weld QualityResistance Spot Welding.SAE AWS D8.7-79S

14、pecification for Automotive Frame Weld QualityArc Welding.3. Notes3.1 Marginal IndiciaThe change bar (I) located in the left margin is for the convenience of the user in locatingareas where technical revisions have been made to the previous issue of the report. An (R) symbol to the left ofthe docume

15、nt title indicates a complete revision of the report.PREPARED BY THE AWS/SAE JOINT COMMITTEE ON AUTOMOTIVE WELDINGSAE J1147 Revised JUN83RationaleNot applicable.Relationship of SAE Standard to ISO StandardNot applicable.ApplicationThe Joint AWS/SAE Committee on Automotive Welding was organized on Ja

16、nuary 16, 1974, forthe primary purpose of facilitating the development and publication of various documents related to theselection, specification, testing, and use of welding materials and practices, particularly for theautomotive and related industries. A secondary purpose is the dissemination of

17、technical information.SAE participation in this activity is intended to insure that the needs and thinking of the industriesmentioned are adequately considered prior to publication of selected Standards, RecommendedPractices, and Information Reports. To this end, such documents are subject to the ap

18、proval of the SAEGeneral Materials Council, as well as the Joint AWS/SAE Committee and the AWS Board of Directions.Documents which are approved by the Council are printed as separate sheets or booklets, with bothAWS D number and SAE HS J number identifications.Reference SectionSAE HS J1156 (AWS D8.6

19、-77)Automotive Resistance Spot Welding ElectrodesSAE HS J1188 (AWS D8.7-78)Specification for Automotive Weld QualityResistance Spot WeldingSAE HS J1196 (AWS D8.8-79)Specification for Automotive Frame Weld QualityArc WeldingSAE HS J836Automotive Metallurgical JoiningDeveloped by the AWS/SAE Joint Committee on Automotive Welding