SAE J 1239-2010 Four- Five- and Eight-Conductor Electrical Connectors for Automotive Type Trailers《汽车型拖车用4- 5-和8-导体电连接器》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J1239_201009SURFACEVEHICLERECOMMENDEDPRACTICEJ1239 SEP2010 Issued 1978-06Revised 2010-09Superse

5、ding J1239 FEB2003 Four-, Five-, and Eight-Conductor Electrical Connectors for Automotive Type Trailers RATIONALEThis document is being revised to add the latest information available and update corrections made during the five year review. TABLE OF CONTENTS 1. SCOPE 32. REFERENCES 32.1 Applicable D

6、ocuments 32.1.1 SAE Publications . 32.1.2 ASTM Publication 32.1.3 ISO Publication . 33. RECEPTACLES 43.1 Four-Way Receptacle . 43.2 Five-Way Receptacle 43.3 Eight-Way Receptacle 44. PLUG 94.1 Four-Way Plug 94.2 Five-Way Plug . 94.3 Eight-Way Plug . 94.3.1 Right Bank Plug 104.3.2 Left Bank Plug . 105

7、. WIRING . 106. HOUSING MATERIAL AND TERMINAL REQUIREMENTS 107. ASSEMBLY REQUIREMENTS . 128. ALTERNATE CONNECTOR SELECTION . 129. NOTES 139.1 Marginal Indicia . 13APPENDIX A EXAMPLES FOR STRANDED CONDUCTORS FOR 12-V CIRCUITS . 14SAE J1239 Revised SEP2010 Page 2 of 14FIGURE 1 FOUR WAY RECEPTACLE 5FIG

8、URE 1A FOUR-WAY RECEPTACLE HARD SHELL VERSION 6FIGURE 2 FIVE-WAY RECEPTACLE 7FIGURE 3 EIGHT WAY RECEPTACLE . 8FIGURE 4 PIN 11FIGURE 5 SOCKET . 12SAE J1239 Revised SEP2010 Page 3 of 141. SCOPE This SAE Recommended Practice covers the wiring and rectangularly shaped connector standards for all types o

9、f trailers whose gross weight does not exceed 4540 kg (10 000 lb). These trailers are grouped in SAE J684 with running light circuit loads not to exceed 7.5 A per circuit. This document provides circuits for lighting, electric brakes, trailer battery charging, and an auxiliary circuit color code and

10、 protection for the wiring from hazards or short circuits. Color code is compatible with SAE J560 and ISO 1724-1980(E). 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of

11、SAE publications shall apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.SAE J560 Primary and Auxiliary Seven Conductor Electrical Connector for Truck

12、-Trailer Jumper Cable SAE J684 Trailer Couplings, Hitches, and Safety Chains - Automotive Type SAE J928 Electrical TerminalsPin and Receptacle Type SAE J1128 Low Voltage Primary Cable SAE J2223-2 Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 2: Tests and General Performanc

13、e Requirements 2.1.2 ASTM Publication Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM G 90-94 Standard Practice for Performing Accelerated Outdoor Weathering of Nonmetallic Materials Using Concentrated Na

14、tural Sunlight 2.1.3 ISO Publication Available from American National Standards Institute, 25 West 43rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org.ISO 1724-1980(E) Road vehicles - Electrical connections between towing vehicles and towed vehicles with 6-or 12-V electrical equipm

15、ent - Type 12 N (normal) ISO 6722 Road Vehicle - 60 V and 600 V single core cables Dimensions, Test methods and Requirements SAE J1239 Revised SEP2010 Page 4 of 143. RECEPTACLES 3.1 Four-Way Receptacle The four-way towing vehicle receptacle shall be of the configuration and design dimensions shown i

16、n Figure 1 and color-coded as follows: a. White - Ground SAE wire size 1 mm2(SAE wire size no. 16 gauge) minimum b. Brown - Tail and license lamp circuit c. Yellow - Left turn and stop circuit d. Green - Right turn and stop circuit 3.2 Five-Way Receptacle The five-way towing vehicle receptacle shall

17、 be of the configuration and design dimensions shown in Figure 2 and color-coded as follows: a. White - Ground SAE wire size 1 mm2(SAE wire size no. 16 gauge) minimum b. Brown - Tail and license light circuit c. Yellow - Left turn and stop circuit d. Green - Right turn and stop circuit e. Blue - Aux

18、iliary 3.3 Eight-Way Receptacle The eight-way towing vehicle receptacle shall be of the configuration and design dimensions shown in Figure 3 color-coded as follows: 3.3.1 Left Bank of Receptacles a. Red - Independent stop b. Blue - Brake circuit spliced to controller of brake c. Optional - Auxiliar

19、y (see Figure 3, Note 1) d. Orange - Battery charge circuit-connect to battery positive terminal through separate fuse or circuit breaker 3.3.2 Right Bank of Receptacles a. White - Battery negative SAE wire size 3 mm2(SAE wire size no. 12 gauge) minimum b. Brown - Tail and license lamp circuit c. Ye

20、llow - Left turn and stop lamp circuit d. Green - Right turn and stop lamp circuit SAE J1239 Revised SEP2010 Page 5 of 14FIGURE 1 - FOUR WAY RECEPTACLE SAE J1239 Revised SEP2010 Page 6 of 14FIGURE 1A - FOUR-WAY RECEPTACLE HARD SHELL VERSION SAE J1239 Revised SEP2010 Page 7 of 14FIGURE 2 - FIVE-WAY R

21、ECEPTACLE SAE J1239 Revised SEP2010 Page 8 of 14FIGURE 3 - EIGHT WAY RECEPTACLE SAE J1239 Revised SEP2010 Page 9 of 143.4 The receptacle leads shall be attached to the vehicle wiring harness in a workmanlike manner, mechanically and electrically secure. Further, a well-insulated strain relief shall

22、be provided between the receptacle and the towing vehicle wiring harness connections so that there will be no strain on the vehicle harness in the event of an abnormal pull on the receptacle. The receptacle shall be placed in a location where it will not be exposed to road hazards either when connec

23、ted or loose. The receptacle leads must be properly routed and protected against damage from cutting and pinching where they leave the vehicle body. Extra insulation should be provided between the strain relief at the trailer hitch and the wiring assembly so that an abnormal pull on the plug will no

24、t damage the wiring. 3.5 No receptacle leads designated for lighting shall be smaller than SAE wire size 1 mm2(SAE wire size no. 16 gauge) minimum if a single conductor, or smaller than SAE wire size 0.8 mm2(SAE wire size no. 18 gauge) if a multiconductor cable. 3.6 No receptacle leads for brake cir

25、cuits shall be smaller than SAE wire 2 mm2(SAE wire size no. 14 gauge) and no circuits shall be smaller than SAE wire 3 mm2for (SAE wire size no. 12 gauge) trailer battery charge circuit or battery return circuit. 3.7 The gauge of conductors for the auxiliary circuits shall be sized to provide at le

26、ast the maximum amperage for the load it will service with a voltage drop not exceeding 3%. The receptacle shall be placed in a location where it will not be exposed to road hazards when disconnected from trailer. 4. PLUG 4.1 Four-Way Plug The four-way towed vehicle plug shall be of the configuratio

27、n and design dimensions shown in Figure 1 or Figure 1A and color coded as follows: a. White - Ground b. Brown - Tail and license lamp circuit c. Yellow - Left turn and stop circuit d. Green - Right turn and stop lamp circuit 4.2 Five-Way Plug The five-circuit plug (Figure 2) shall be color-coded and

28、 attached to the trailer harness as follows: a. White - Ground b. Brown - Tail and license lamp c. Yellow - Left turn and stop lamp d. Green - Right turn and stop lamp e. Blue - Auxiliary 4.3 Eight-Way Plug The eight-circuit plug (Figure 3) shall be color coded as follows: SAE J1239 Revised SEP2010

29、Page 10 of 144.3.1 Right Bank Plug a. Red - Independent stop b. Blue - Brake circuit spliced to controller of brake circuit c. Optional - Auxiliary (see Figure 3, Note 1) d. Orange - Battery Charge Circuit - Connect to trailer battery positive terminal through separate fuse or circuit breaker 4.3.2

30、Left Bank Plug a. White - Ground to frame and trailer battery negative terminal b. Brown - Tail and license lamp circuit c. Yellow - Left turn and stop lamp circuit d. Green - Right turn and stop lamp circuit 5. WIRING All wire and insulation shall conform to the requirements of SAE J1128 Reference

31、Low Tension Primary Cable data on stranded conductors or ISO 6722 Metric Wire stranded conductors for 12-V circuits. It is suggested that SAE J1128 Low Tension Primary Cable or Metric Wire stranded conductors for 12-V circuits should not exceed a 3% voltage drop (see Appendix A, Figures A1 and A2).

32、5.1 Exposed trailer wiring shall be run in conduits or secured at intervals not greater than 457 mm (18 in) to stop lateral movement and prevent rubbing or chafing. 5.2 So far as practicable, wiring should be located to afford protection from road splash, stones, or abrasion. Wiring exposed to such

33、conditions shall use additional tape, plastic sleeve, nonmetallic conduit, and/or other suitable shielding or covering to further protect the wiring. 6. HOUSING MATERIAL AND TERMINAL REQUIREMENTS 6.1 The receptacle and plug shall be made of an insulating material such that they can be processed to p

34、rovide the spacing and splash protection indicated in Figures 1, 2, and 3. 6.2 If the receptacles and plugs are fabricated of either molded or extruded plastic, the plastic material shall be stabilized for protection against exposure to ultraviolet light.6.3 Housing Material Types 6.3.1 Soft Molded

35、Plugs and Receptacles The hardness of a soft molded receptacle or plug shall fall between Shore A 50 and Shore A 85.6.3.2 Hard Molded Receptacles (tow-vehicle side) Hard molded plastics such PA and PBT. Materials may contain added reinforcement material.SAE J1239 Revised SEP2010 Page 11 of 146.4 Ter

36、minal Requirements 6.4.1 The terminal pins and receptacles sockets shown in Figures 1, 2, and 3 shall conform to the size and type shown in SAE J928, Table 1 - Type 1 Pin Terminals with a nominal diameter of 4.57 mm (0.180 in). Detailed pin and receptacle dimensions are illustrated in Figures 4 and

37、5. FIGURE 4 - PIN SAE J1239 Revised SEP2010 Page 12 of 14FIGURE 5 - SOCKET 6.4.2 The terminal pins and receptacles shall be fabricated from a copper alloy material and suitably coated to protect against corrosion. Finished surfaces of terminal pins and interior walls of terminal receptacles shall be

38、 smooth so as not to bind when the parts are engaged. 7. ASSEMBLY REQUIREMENTS 7.1 The plug and receptacle of a four-way connector assembly shall disengage with a minimum force of 22.24 N (5 lb) and a maximum force of 88.96 N (20 lb) per assembly. 7.2 The plug and receptacle of a five-way connector

39、assembly shall disengage with a minimum force of 31.14 N (7 lb) and a maximum force of 111.2. N (25 lb) per assembly7.3 The plug and receptacle of an eight-way connector assembly shall disengage with a minimum of 35.58 N (8 lb) and a maximum force of 133.44 N (30 lb) per assembly. 7.4 The mechanical

40、 force requirements of disengagement do not preclude the requirements for good electrical connections between the male and female connectors of the circuits. 8. ALTERNATE CONNECTOR SELECTION This specification provides fundamental performance characteristics pertaining to mold-on connectors, which h

41、ave been established for Class I trailer applications. There is no intention to limit the application to the example four-, five-, and eight-way pin/sleeve connectors, provided that mating pair connectors have equal or superior performance characteristics. Also, additional performance standards for

42、connectors can be referenced in SAE J2223-1, SAE J2223-2, and SAE J2223-3. SAE J1239 Revised SEP2010 Page 13 of 149. NOTES 9.1 Marginal Indicia A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been

43、 made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY THE

44、 SAE CONNECTOR SYSTEMS STANDARDS COMMITTEE SAE J1239 Revised SEP2010 Page 14 of 14APPENDIX A - EXAMPLES FOR STRANDED CONDUCTORS FOR 12-V CIRCUITS NOTE: This abstracted table is not intended to limit conductor constructions but samples the stranding range shown. Reference: Should also consider ISO 6722 Road vehicles - 60 V and 600 V single - core cables - Dimensions, test methods and requirements. FIGURE A1 - STRANDED CONDUCTORS FOR 12-V CIRCUITS(PRIMARY CABLE DATA ABSTRACTED FROM SAE J1128) 3% VOLTAGE DROP FIGURE A2 - MAXIMUM LENGTH OF CONDUCTOR IN FEET FROM POWER SOURCE TO LOAD