SAE J 1402-2010 Automotive Air Brake Hose and Hose Assemblies《汽车汽闸制动软管和软管组件》.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication m

3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U

4、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/J1402_201008SURFACEVEHICLERECOMMENDEDPRACTICEJ1402 AUG2010 Issued 1942-01 Revised 2010-08Supers

5、eding J1402 JAN2005 Automotive Air Brake Hose and Hose Assemblies RATIONALE This revision corrects an error on the direction of the layline in Figure 2 and adds an explanation of the meaning of a cycle in clause 8.4. 1. SCOPE This recommended practice covers minimum requirements for air brake hose a

6、ssemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed topotential pull or

7、impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40 to +100 C. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of S

8、AE publications shall apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.SAE J517 Hydraulic Hose SAE J1401 Road VehicleHydraulic Brake Hose Assemblies

9、for Use with Nonpetroleum-Base Hydraulic Fluids 2.1.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM B 117 Standard Test Method of Salt Spray (Fog) Testing ASTM D 380 Standard Test Meth

10、ods for Rubber Hose ASTM D 413 Test Methods for Rubber PropertyAdhesion to Flexible Substrate Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1402 Revised AUG2010 Page 2 of 93. HOSE CONSTRUCTIONS AND DIMENSIONS There are four distinct hose const

11、ructions used for air brake hose assemblies made from reinforced elastomeric hose. All dimensions are in accordance with Tables1 and 2. Type A consists of an elastomeric tube, a fiber reinforcement and an elastomeric cover. Type AI consists of an elastomeric tube, a wire or fiber reinforcement and a

12、 fiber braid cover. Type AII consists of an elastomeric tube, a wire or fiber reinforcement and a fiber braid or elastomeric cover. This hose is dimensionally identical to SAE J517 100R5 hose. Type AIII consists of an elastomeric tube, wire or fiber reinforcement and a fiber braid or elastomeric cov

13、er. TABLE 1 - INSIDE AND OUTSIDE DIAMETERS FOR TYPE A AND AIII HOSES All dimensions in mm, unless otherwise specified MetricSize Inch Size (Ref) SAEType A Dash Size (Ref) TypeAI.D.MinTypeAI.D.MaxTypeAO.D.MinTypeAO.D.MaxSAEType AIII Dash Size (Ref) TypeAIII I.D.MinTypeAIII I.D.MaxTypeAIIIO.D.MinTypeA

14、III O.D.Max6.3 1/4 -4 5.8 6.9 15.1 16.7 -4 6.2 7.0 12.0 14.0 8 5/16 -5 7.3 8.5 16.7 18.3 10 3/8 -6 8.9 10.1 18.3 19.8 -6 9.3 10.1 15.5 17.5 11.5 7/16 -7 10.3 11.9 19.8 21.4 12.5 SP 1/2 SP -8 11.9 13.5 21.4 23.0 12.5 1/2 -8 12.3 13.5 19.0 21.0 16 5/8 -10 15.1 16.7 26.2 27.8 -10 15.5 16.7 22.7 24.7 NO

15、TE: The sizes 3/8, 7/16 and 1/2 SP of Type A hose can be assembled with field attachable fittings if desired. These field attachable fittings are not the same as used with Types AI and AII hoses. AIII hoses are assembled with permanent crimp fittings only. TABLE 2 - INSIDE AND OUTSIDE DIAMETERS FOR

16、TYPE AI AND AII HOSES All dimensions in mm, unless otherwise specified MetricSize Inch Size (Ref) SAE Type AI and AIIDash Size(Ref) TypeAI and AII I.D.MinType AI and AIII.D.MaxTypeAIO.D.MinTypeAIO.D.MaxTypeAIIO.D.MinTypeAII O.D.Max5 3/16 -4 4.8 5.5 12.0 13.0 12.7 13.7 6.3 1/4 -5 6.4 7.2 13.6 14.6 14

17、.3 15.3 8 5/16 -6 7.9 8.7 15.1 16.2 16.7 17.6 11 13/32 -8 10.3 11.1 18.1 19.3 18.9 20.0 12.5 1/2 -10 12.7 13.7 20.5 21.7 22.8 24.0 16 5/8 -12 15.9 17.0 23.7 24.9 26.8 28.0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1402 Revised AUG2010 Page

18、 3 of 94. FITTINGS 4.1 For Permanently Attached Fittings When the hose is assembled with permanently attached fittings, the hose portion of the hose assembly shall conform to the dimensional requirements of Type A or AIII hose in Table 1 and AI or AII hose in Table 2. 4.2 For Field Attachable Fittin

19、gs When the hose is assembled with field attachable fittings, the hose portion of the hose assembly shall conform to the dimensional requirements for all sizes of Type AI or AII hose in Table 2 or shall conform to the dimensional requirements of 3/8, 7/16 and 1/2 SP Type A hose from Table 1. The fie

20、ld attachable fittings for Type A hose are not the same as used with Types AI and AII hoses. NOTE: The sizes 3/8, 7/16 and 1/2 SP of Type A hose can be assembled with field attachable fittings if desired. These field attachable fittings are not the same as used with Types AI and AII hoses. 5. MINIMU

21、M BEND RADIUS Table 3 contains the minimum bend radii recommended for vehicle installations. TABLE 3 - RECOMMENDED MINIMUM BEND RADIUS Metric Size Inch Size (Ref) Minimum Bend Radius To Inside of Bend (mm) 5 3/16 50 6.3 1/4 65 8 5/16 75 10 3/8 90 11 13/32 90 11.5 7/16 100 12.5 SP 1/2 SP 100 12.5 1/2

22、 10016 5/8 115 6. IDENTIFICATION 6.1 Hose Each hose manufacturer shall incorporate into the hose construction an identification yarn as assigned by the RMA and as shown in Appendix A, Table A1 of SAE J1401. Each air brake hose shall also be labeled in a color contrasting to that of the hose and labe

23、ling shall be repeated every 600 mm or less along the entire length of hose in legible block capital letters at least 3 mm high with the following minimum information in the order listed: a. The hose manufacturers identification XXXXX b. The words “AIR BRAKE” to identify specific hose application c.

24、 The hose metric size, such as Size 8 d. SAE J1402 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1402 Revised AUG2010 Page 4 of 9Example: XXXXX AIR BRAKE Size 8 SAE J1402 In addition, each air brake hose shall be labeled with either an A, AI,

25、AII, or AIII, identifying whether the hose has been manufactured to the dimensions of A, AI, AII, or AIII hose as shown in Tables 1 and 2. This additional labeling need not appear on the same layline as the above (a), (b), (c) and (d) information, but shall have the same minimum requirements of colo

26、r contrast, spacing and letter height. 6.2 Fittings Each field attachable air brake hose fitting shall be permanently etched, embossed or stamped in legible block capital letters at least 1.5 mm high with the coupling manufacturers identification, hose size and whether they are intended for use with

27、 Type A, AI, or AII hose. 6.3 Assemblies Each air brake hose assembly shall be identified by means of a band around the hose. The band may move freely along the length of the assembly as long as it is retained by the end fitting. The band shall be permanently etched, embossed or stamped in legible b

28、lock capital letters at least 3 mm high with the following information: a. The month, day and year, or the month and year the assembly was made expressed in numerals. For example, 3/1/75 means March 1, 1975 or 3/75 means March 1975. b. The assemblers identification and additional information as requ

29、ired. 7. PERFORMANCE NOTE 1: All samples subjected to one or more performance tests other than Proof Pressure and Length Change shall be destroyed and discarded after completion of the tests and their analysis. NOTE 2: Burst Strength and Assembly Tensile Strength tests are qualification tests and do

30、 not imply that the hose assemblies can be used under those conditions. 7.1 Acceptance Performance Hose or hose assemblies at the time of manufacture shall conform to the following: 7.1.1 End Fittings End fittings shall be such as to permit conformance to all portions of this recommended practice. A

31、fter assembly of the end fittings to the hose, the minimum I.D. of the end fittings or the hose shall not be less than 66% of the minimum hose ID shown in Table 1. All hose assemblies shall pass this requirement prior to conducting any other test in this recommended practice. 7.1.2 Proof Pressure As

32、semblies subjected to a pressure test using 2 MPa 0.1 MPa air or nitrogen under water for a minimum of 30 s shall show no leaks. 7.1.3 Burst Strength There shall be no hose burst, leakage or end fitting separation below 6 MPa when hose or hose assemblies are subjected to a hydrostatic burst test usi

33、ng water. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1402 Revised AUG2010 Page 5 of 97.1.4 Assembly Tensile Strength 450 mm long hose assemblies including the fittings shall be subjected to a longitudinal tensile test at a steady rate of 25

34、 mm/min 2.5 mm/min until separation of the hose from the fittings or rupture of the hose occurs. Failure of the 6.3 mm and smaller size shall occur at no less than 1100 N and larger sizes at no less than 1450 N. 7.1.5 Length Change Test for length change shall be conducted in accordance with ASTM D

35、380 (Elongation and Contraction) with the original measurement made at 0.1 MPa. The change in length shall be determined at 1.5 MPa and shall be from +5% to 7%. 7.1.6 Adhesion Tests for adhesion shall be conducted only on original unaged specimens as follows: 7.1.6.1 Adhesion of Fiber Reinforced Hos

36、e Test for adhesion shall be conducted in accordance with ASTM D 413 Machine Method, and the average load required to separate any adjacent layers shall be 1.4 N/mm minimum. Type AIII consists of an elastomeric tube, wire or fiber reinforcement and a fiber braid or elastomeric cover. 7.1.6.2 Adhesio

37、n of Wire Reinforced Hose The requirements and method of testing cover adhesion for Type AI, AII, and AIII hoses with wire reinforcement shall be as in 7.1.6.1. The integrity of the inner tube adhesion shall be tested by subjecting a length of hose not less than 380 mm long to the following requirem

38、ents: Place a steel ball of the size specified in Table 4 in the bore of the hose. One end of the hose shall be attached to a vacuum source and the other end plugged. A vacuum of 17 kPa absolute shall be applied for a period of 5 min while the hose is in an essentially straight position. At the conc

39、lusion of this period and while still under vacuum, the hose shall be bent 180 degrees to the minimum bend radius in Table 3 in each of two directions 180 degrees apart. After bending and returning to an essentially straight position and while still under vacuum, the ball shall be rolled from end to

40、 end of the hose. Failure of the ball to pass freely from end to end shall be indication of separation of the inner tube from the reinforcement layer and shall constitute failure. TABLE 4 - BALL SIZE FOR TESTING ADHESION OF WIRE REINFORCED HOSE Metric Size 5 6.3 8 11 12.5 16 Inch Size (Ref) 3/16 1/4

41、 5/16 13/32 1/2 5/8 Ball Size (mm) 3.5 4.5 6.0 7.5 9.5 12.0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J1402 Revised AUG2010 Page 6 of 97.2 Qualification Performance For initial qualification under this specification all of the requirements

42、under Acceptance Performance, Qualification Performance and Flexure Test shall be met. Minimum sampling shall be per Table 5, including the specified sequential test procedure. TABLE 5 - MINIMUM SAMPLING AND SEQUENTIAL TEST PROCEDURE Sample No. Subjected to Followed by 1 7.1.1(1)7.2.1.1 then 7.1.2 2

43、 7.1.1(1)7.2.1.2 then 7.1.2 3 7.2.2.1 4 7.1.1(1)7.2.2.2 then 7.1.4 5 7.2.2.3 6 7.1.1(1)7.2.2.4 then 7.1.3 7 7.1.1(1)7.1.5 then 7.1.2 and 7.1.3 8 7.1.6 9 7.1.1(1)8. 1. Couple hose before starting tests or aging. 7.2.1 Temperature Resistance 7.2.1.1 High Temperature Resistance The hose portion of a ho

44、se assembly shall show no cracks, charring or disintegration externally or internally when straightened after being bent over a form for a period of 70 h 2 h while in an air oven at 100 C 2 C. The radius of the test form shall be in accordance with Table 3. The external surface of fiber braid covere

45、d hoses shall be exempt from inspection for cracks as visual inspection is not practical. After completion of this test, the hose assembly shall be tested in accordance with 7.1.2. 7.2.1.2 Low Temperature Resistance The hose shall show no cracks externally or internally when bent 180 degrees over a

46、form having the radius shown in Table 3 after hose and form have been exposed for a period of 70 h 2 h in an air circulating chamber at 40 C 2 C and while still at this temperature. The hose and form shall be supported by a non-metallic surface during the entire period. The bend shall be completed i

47、n a period of 3 to 5 s. The external surface of fiber braid covered hoses shall be exempt from inspection for cracks as visual inspection is not practical. 7.2.2 Resistance to Environment 7.2.2.1 Oil Specimens prepared from the inner tube and the cover shall show a volume increase when measured afte

48、r removal from ASTM IRM 903 oil in which it has been immersed for 70 h 2 h at 100 C 2 C of not more than 100%. 7.2.2.2 Water Condition hose assembly by immersion in distilled water at room temperature for a period of 168 h 2 h while bent over a form having the minimum bend radius shown in Table 3. Ends shall be completely capped during immersion. After completion of this test, the hose assembly shall be tested in accordance with 7.1.4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license f