ImageVerifierCode 换一换
格式:PDF , 页数:4 ,大小:22.06KB ,
资源ID:1027281      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-1027281.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(SAE J 864-1984 Surface Hardness Testing with Files Recommended Practice.pdf)为本站会员(inwarn120)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

SAE J 864-1984 Surface Hardness Testing with Files Recommended Practice.pdf

1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefro

2、m, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.QUESTIONS REGARDING THIS DOCUMENT: (724) 772-8512 FAX: (724) 776-0243TO PLACE A DOCUMENT

3、 ORDER; (724) 776-4970 FAX: (724) 776-0790SAE WEB ADDRESS http:/www.sae.orgCopyright 1993 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.S.A.SURFACEVEHICLE400 Commonwealth Drive, Warrendale, PA 15096-0001RECOMMENDEDPRACTICEAn American National StandardJ864REAF.MAY93Issued 196

4、3-06Reaffirmed 1993-05Superseding J864 DEC88SURFACE HARDNESS TESTING WITH FILESForewordThis Reaffirmed Document has been changed only to reflect the new SAE Technical Standards BoardFormat.1. ScopeHardness testing with files consists essentially of cutting or abrading the surface of metal parts, and

5、approximating the hardness by the feel, or extent to which, the file bites into the surface. The term “file hard“means that the surface hardness of the parts tested is such that a new file of proven hardness will not cut thesurface of the material being tested.1.1 ApplicationThis SAE Recommended Pra

6、ctice describes the technique of using a file for testing the surfacehardness of miscellaneous iron and steel parts as designated by engineering specifications. In presenting thisprocedure, it is recognized that it is subjective and that it must be used with considerable judgment on the partof the o

7、perator. File hardness tests may be used when case depth is too shallow for conventional indentationhardness methods, to detect the presence of a soft surface condition on hardened or case-hardened parts, orto check the hardness of sintered parts that may not respond predictably to indentation hardn

8、ess methods.The method is useful in production control.2. ReferencesThere are no referenced publications specified herein.3. Apparatus Required3.1 Standard FilesHand files meeting the following requirements:a. 150 or 200 mm (6 or 8 in) pillarb. No. 1 Swiss double cutc. 26 cuts per cm (66 per in)d. H

9、ardness of File65 to 68 HRC designated No. 6561 to 63 HRC designated No. 6257 to 59 HRC designated No. 5854 to 56 HRC designated No. 5549 to 51 HRC designated No. 50SAE J864 Reaffirmed MAY93-2-e. Chemical CompositionCarbon1.20 to 1.40%Manganese0.20 to 0.40%Phosphorus0.40% maxSulfur0.05% maxSilicon0.

10、10 to 0.20%3.2 Standard ProverStandard steel or iron test pieces, 50 mm (2 in) dia and approximately 6 mm (1/4 in) thick,hardened and tempered to the hardness of the lower limit of each standard file range, are required for testingthe standard files.The prover shall be filed with a discarded test fi

11、le to remove any hard or soft skin that will interfere with theaccuracy of the test. Similar provers hardened to the ranges in Table 1 and above the medians can be used toprove the file will cut below and not above the designated file hardness.Testing of files is performed by passing the test file a

12、cross the 6 mm (1/4 in) thick face of the prover.A 6 mm (1/4 in) prover is specified because at the higher hardnesses, the surface area contacted affects thecutting area considerably. Narrow areas can be cut more readily than wide areas due to the concentration ofpressure that may be obtained.3.3 St

13、andard Test PiecesStandard test pieces (of the same contour, steel or iron composition, and heattreatment) varying in hardness by small increments, with which the parts being inspected can be compared,are recommended. In the case of steels, each family of SAE steels, namely, 10XX, 20XX, 30XX, and th

14、e likeshould be used. They can be heat treated to compare with the operation, such as carburized, quenched, andtemper or carbonitrided, quenched, and temper.These pieces will enable the operator to learn, with fair accuracy, the feel of the file as it cuts, or does not cut,in relation to the Rockwel

15、l hardness.Table 1CHART OF FILES AND PROVERSFile No.Standard ProverHardnessProver CuttingHardnessProver NoncuttingHardnessUntempered65 65 HRC 63 HRC 67 HRCTempered(1)1. Using tempered files below 65 HRC is less accurate and, therefore, more judg-ment on the part of the operator must be exercised as

16、the hardness of the file decreases.62 61 HRC 60 HRC 64 HRC58 57 HRC 56 HRC 60 HRC55 54 HRC 53 HRC 57 HRC50 49 HRC 48 HRC 52 HRCSAE J864 Reaffirmed MAY93-3-4. Surface ConditionIn testing high surface hardnesses with a file, experience has shown that surfacecondition is important; very smoothly ground

17、 surfaces cannot be touched with a file as readily as surfaces thathave been filed. Sometimes a testing file will cut a prover of a certain steel at, for example, 64 HRC, yet whenthe file is applied to a smoothly ground part made of the same steel and at the same hardness, the part feelsharder. It i

18、s important when comparisons are made that the surface smoothness of the parts being tested bethe same as the standard test piece. The standard test pieces can be made in a series of microfinish of 0.5,1.5, 3.2, and 5 m (20, 60, 125, and 200 in).On surfaces with a microfinish, the direction of the t

19、est filing across or parallel with the finish direction affectsresults. When filing, the direction of the file in relation to the microfinish should always be the same as thestandard test piece.5. Testing Hardness5.1 Check file against standard prover.5.2 Apply the file to the surface of the part be

20、ing tested at such an angle that only a few teeth will engage thesurface at once. Use slow, firm strokes in an effort to feel the manner in which the file cuts or does not cut. Toprolong the life of the file, use as short a stroke as possible.NOTETo standardize pressure, attach specimen to a balance

21、 scale platform and measure the file effortagainst specimen in kilograms (pounds). Application should be between 4.5 and 5.5 kg (10 and 12 lb).5.3 Compare the parts with a standard test piece with a known hardness range. This will assist in determiningwhether the part falls within the range specifie

22、d by the engineering specifications. File hardness should notreplace conventional methods where penetrators will not break through surface hardened areas.NOTEDuring the testing of a batch of parts, the files must not be allowed to become so dull as to causedifficulty in discriminating between parts

23、within specification and those below specification. This canbe prevented by frequent checking against the standard part or prover.5.4 The hardness should be specified according to the Rockwell reading of the file as to the surface requirementsof an iron or steel part. The designation should be “file

24、 hard - 65“ for 65 HRC surface; “file hard - 62“ for62HRC and so on.6. Sources of Test Files6.1 Simonds Cutting Tools, Newcomerstown, Ohio. Available through distributors in boxes of 10 files per hardnesslevel.6.2 Nicholson Files, Raleigh, North Carolina. Available in minimum quantities of 600.PREPA

25、RED BY THE SAE IRON AND STEEL TECHNICAL COMMITTEE 3TEST PROCEDURESSAE J864 Reaffirmed MAY93RationaleNot applicable.Relationship of SAE Standard to ISO StandardNot applicable.ApplicationHardness testing with files consists essentially of cutting or abrading the surface of metal parts,and approximatin

26、g the hardness by the feel, or extent to which, the file bites into the surface. The term“file hard“ means that the surface hardness of the parts tested is such that a new file of proven hardnesswill not cut the surface of the material being tested.Reference SectionThere are no referenced publications specified herein.Developed by the SAE Iron and Steel Technical Committee 3Test ProceduresSponsored by the SAE Iron and Steel Executive Committee

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1