SAE J 933-2013 Mechanical and Quality Requirements for Tapping Screws《自攻螺钉的机械和质量要求》.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J933_201302 SURFACE VEHICLE RECOMMENDED PRACTICE J933 FEB2013 Issued 1965-07 Stab

5、ilized 2013-02 Superseding J933 AUG2005 Mechanical and Quality Requirements for Tapping Screws RATIONALE Current requirements for Tapping Screws are contained in ASME B18.6.3 - Machine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series) and SAE J2596 - Fastener Part Standard - Tapping Sc

6、rews and Metallic Drive Screws (Inch Dimensioned). SAE J933 contains useful information and may have current users. STABILIZED NOTICE This document has been declared “Stabilized“ by the SAE Fasteners Committee and will no longer be subjected to periodic reviews for currency. Users are responsible fo

7、r verifying references and continued suitability of technical requirements. Newer technology may exist. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J933 Stabilized FEB2013 Page 1 of 9 Copyrig

8、ht SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J933 Stabilized FEB2013 Page 2 of 9 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitte

9、d without license from IHS-,-,-SAE J933 Stabilized FEB2013 Page 3 of 9 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J933 Stabilized FEB2013 Page 4 of 9 Copyright SAE International Provided by

10、IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J933 Stabilized FEB2013 Page 5 of 9 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SA

11、E J933 Stabilized FEB2013 Page 6 of 9 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J933 Stabilized FEB2013 Page 7 of 9 Copyright SAE International Provided by IHS under license with SAENot for

12、 ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J933 Stabilized FEB2013 Page 8 of 9 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J933 Stabilized FEB2013 Page 9 ofSTABILIZED BY THE SAE FASTENERS COMMITTEE Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-