ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:18.31KB ,
资源ID:1027416      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-1027416.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(SAE J 2548-2001 Test Method to Obtain Lug-Up Torque Data for Heavy-Duty Truck and Bus Engines.pdf)为本站会员(boatfragile160)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

SAE J 2548-2001 Test Method to Obtain Lug-Up Torque Data for Heavy-Duty Truck and Bus Engines.pdf

1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefro

2、m, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.TO PLACE A DOCUMENT ORDER: +01 724-776-4970 FAX: +01 724-776-0790SAE WEB ADDRESS http:/w

3、ww.sae.orgCopyright 2001 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.S.A.SURFACEVEHICLE400 Commonwealth Drive, Warrendale, PA 15096-0001RECOMMENDEDPRACTICESubmitted for recognition as an American National StandardJ2548 ISSUEDAPR2001Issued 2001-04Test Method to Obtain Lug-U

4、p Torque Data for Heavy-Duty Truck and Bus Engines1. ScopeThis SAE Recommended Practice applies to all forms of diesel and natural gas engines fueled by thecombination of diesel fuel and natural gas.1.1 PurposeThis document provides a method to determine the torque generating capability of an engine

5、 as itaccelerates away from idle at a specified acceleration rate. The data is typically used to aid in the propermatching of the engine to the available torque converters of a torque converter equipped transmission. Thegoal is to achieve acceptable off-idle transient engine acceleration against the

6、 load of a torque converterequipped vehicle as it moves away from a stop.2. References2.1 Applicable PublicationThe following publication forms a part of this specification to the extent specifiedherein. Unless otherwise indicated, the latest issue of SAE publications shall apply.2.1.1 SAE PUBLICATI

7、ONAvailable from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.SAE J1995Engine Power Test CodeSpark Ignition and Compression IgnitionGross Power Rating3. ProcedureA dynamometer with automatic engine acceleration rate control is required. The test starts withthe engine idling against a typic

8、al curb idle torque load of a stopped vehicle equipped with a torque convertertransmission in gear. The throttle is then snapped open to wide open throttle. At the point that the throttle issnapped open, the dynamometer is to automatically control the rate of engine acceleration to 175 rpm/s. SAEJ19

9、95 gross torque versus engine rpm is then to be recorded until the engine approaches its high idle or noload rpm. It may be necessary to obtain the torque data via a driveline mounted torque meter between theengine and dynamometer in order to account for the torque required just to accelerate the in

10、ertia of thedynamometer.4. Data ReportingThe acceleration gross torque versus engine rpm data per this document is to bedocumented in writing for use by the industry.PREPARED BY THE SAE TRUCK AND BUS ENGINE PERFORMANCEAND APPLICATION SUBCOMMITTEE OF THESAE TRUCK AND BUS POWERTRAIN COMMITTEESAE J2548

11、 Issued APR2001RationaleNot applicable.Relationship of SAE Standard to ISO StandardNot applicable.ApplicationThis SAE Recommended Practice applies to all forms of diesel and natural gas engines fueledby the combination of diesel fuel and natural gas.Reference SectionSAE J1995Engine Power Test CodeSpark Ignition and Compression IgnitionGross Power RatingDeveloped by the SAE Truck and Bus Engine Performance and Application SubcommitteeSponsored by the SAE Truck and Bus Powertrain Committee

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1