1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2012 SAE International All rights reserved. No part of this pub
3、lication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970
4、(outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J3011_201210SURFACEVEHICLERECOMMENDEDPRACTICEJ3011 OCT2012 Issued 2012-10Measurement
5、 and Characterization of Electronically Controlled All-Wheel Drive/Driveline Coupling Systems RATIONALETo recommend test configuration parameters, procedures, and analysis techniques of electronically controlled all-wheel drive (AWD)/driveline coupling system for measurement of specific performance
6、characteristics. FOREWORDThe intended scope of this SAE Recommended Practice is to encompass all types of electronically controlled driveline coupling devices including active on-demand (AOD) and cross axle devices. This practice is not intended for launch devices and transmission related systems.1.
7、 SCOPE This SAE Recommended Practice covers the most common applications of electronically controlled on-demand AWD couplings used in passenger (car and light truck) vehicle applications. 2. PURPOSE The purpose of this SAE Recommended Practice is to provide a means to define, measure, and quantify t
8、he operating characteristics of electronically controlled on-demand AWD coupling systems. 3. REFERENCES 3.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply.
9、Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.SAE J1952 All-Wheel Drive Systems ClassificationSAE J3011 Issued OCT2012 Page 2 of 18 4. DEFINITION Electronically-controlled coup
10、ling systems consist of a mechanical coupling device controlled by an electronic control unit (ECU). The ECU contains control algorithms and the communication interface to allow access to key vehicle information as well as for communication with such systems as anti-lock braking systems (ABS), elect
11、ronic stability control (ESC) systems, etc., (please reference J1952 for further definitions). As a result of this level of vehicle system integration, the performance of the coupling may be assessed either with or without an ECU.In order to reduce the fuel consumption of passenger vehicles, AOD cou
12、pling systems may incorporate a driveline disconnect or two-wheel drive (2WD) mode that substantially reduces drag torque, (typically at the expense of response time). The unique usage of these devices makes it important to distinguish between standard couplings and couplings with disconnect capabil
13、ity. Except where noted, all test procedures outlined in this document should be made and measured while in the AWD mode. Notable exceptions to this include the measurement of drag torque losses in section 11.The rated torque capacity of the device shall be defined by the device supplier. 5. SYSTEM
14、CONTROL METHODOLOGY A vehicle representative ECU or other electronic control method may be used to control the coupling. In any case, coupling performance will be assessed based on when a commanded input is first received by the coupling or ECU, as shown in Figure 1. The particular system control me
15、thodology used must be defined and documented as part of the data reporting process.FIGURE 1 - COUPLING TEST CONTROL METHODOLOGY SAE J3011 Issued OCT2012 Page 3 of 18 6. TEST RIG SET-UP Coupling output is to be grounded (stationary) with an inline torque transducer recommended on the grounded side,
16、as shown in Figure 2 (optionally, the torque transducer may be located on the rotating input side or in a reactionary torque arm, so long as all accuracy and system requirements are achieved). Two fixturing options are acceptable. 1. Grounding the clutch housing. 2. Grounding the main shaft. FIGURE
17、2 - TEST RIG SET UPBasic test rig capabilities should include the following: Maximum torque capacity shall be a minimum of 10% above the test requirements. Torque transducer resolution shall be 0.50% of full scale based on 150% of the rated clutch torque capacity for all testing except Section 11. F
18、or drag torque in connected mode, measurement resolution shall be 0.75 Nm, and for disconnect capable couplings, the resolution shall be 0.05 Nm. Maximum speed capacity should be a minimum of 10% above test requirements. The measured speed sensor shall be mounted to the unit under test, where the dy
19、no output stiffness shall be ten times the theoretical torsional stiffness of the coupling. Speed shall be controlled to within 0.5 RPM or 0.50% of max RPM, whichever is greater. Minimum and maximum speed requirements: o Connected mode: 2 - 200 RPM o Disconnected mode: up to 3000 RPM o If ramp up ra
20、tes indicated in section 11 cannot be achieved, please indicate actual rates used for the test. SAE J3011 Issued OCT2012 Page 4 of 18 Minimum and maximum temperature respectively: (-40 to 150 C) Clutch initial condition temperature shall be measured at either: (as shown in Figure 3) 1. Clutch reacti
21、on plate by grounding the clutch housing and spinning the main shaft. 2. Core of the main shaft by grounding it and spinning the outer housing. If the temperature sensor is located in the main shaft, it is unacceptable to run more than one cycle before thermally reconditioning (cold soaking) the tes
22、t unit since the difference in temperature between the clutch housing and the main shaft may be significant, as shown in Figure 4. This graph demonstrates the thermal deviations between the clutch plates, sump, inner shaft, and skin of the coupling, thus requiring special cooling practices in betwee
23、n sections and cycles. It also shows why clutch housing surface temperature cannot be used for control temperature. Coupling testing shall be performed in two phases. 1. As shipped new coupling intended for installation in a production vehicle. 2. Target Life coupling which has completed the life cy
24、cle durability testing. FIGURE 3 - TEMPERATURE SENSOR LOCATION OPTIONS SAE J3011 Issued OCT2012 Page 5 of 18 FIGURE 4 7. TESTING AND ANALYSIS For the purpose of characterizing the system performance, the recommended tests for the full coupling assembly will consist of: Step Input Section 9 Dynamic R
25、esponse Profile Section 10 Drag Torque Behavior Section 11 Mu-V characteristics Section 12 8. GENERAL TEST REQUIREMENTS All single point data collection shall be run a minimum of three times for all test sections. The data shall be tabulated for the three sets and averaged as a final graph.Due dilig
26、ence shall be taken to stabilize the coupling temperature between runs for at least 30 minutes or as required to ensure the desired core temperature has been reached. Stabilized temperature is defined by the temperature fluctuating less than two degrees once it is within the required temperature ran
27、ge. 9. STEP INPUT TEST The purpose of this test is to characterize the torque engagement and release response of the system at various delta speeds and start temperatures whilst at various requested torque levels (see Figure 5). 9.1 Minimum level of parameters to be monitored and recorded: Coupling
28、reacted torque. Coupling temperature (measured according to the options outlined above). Delta speed. Coupling input current, voltage and pressure (where applicable). SAE J3011 Issued OCT2012 Page 6 of 18 9.2 Coupling Torque Measurement Procedure: Document 100% and 50% of the couplings rated torque
29、capacity. Supply a report on two couplings. 1. As shipped new coupling intended for installation in a production vehicle. 2. Target Life coupling which has completed the life cycle durability testing (such as from Design Validation testing). NOTE: The total energy profile showing, load vs. speed vs.
30、 time and Joules exerted during the test shall be provided with the test report. The results should be tabulated in the matrix shown in Table 1. Torque evaluation with and without ECU (if applicable). o With ECU: Response time to be measured from the input of the Clutch Command torque request (Nm) i
31、nto the actuator controller (see Figure 1) to the measured reacted torque of the coupling. ECU processing time is included in the total response time. o Without ECU: Response time to be measured from the initial application of actuator power (see Figure 1) to the final reacted torque of the coupling
32、. Test conditions: o Controlled power source capability for the ECU (12 V 3 V) o Sampling rate: 1024 Hz (to capture 100 ms response time) o Coupling start temps: -20 C, 0 C, +20 C, +50 C, +100 C, (2 C) 5 RPM 10 RPM Steady state 20 RPM Dynamic event 50 RPM Homogeneous launch 100 RPM Step Mu. Curb 150
33、 RPM Step Mu. Curb + 50% (GVWR - Curb) 200 RPM Step Mu. GVWR SAE J3011 Issued OCT2012 Page 7 of 18 FIGURE 5 9.2.1 Step Input Data Analysis Characterization: Command Torque: c(t): Commanded torque expressed in terms of target torque percentage. Target Torque (Tt): The desired torque value commanded b
34、y the control system Settled Torque (Ts): Defined after the torque has settled and reached the steady state region (after ts). Point with the greatest deviation shall be picked as the result. Note: also known as “actual torque” Torque Accuracy (Ta): The greatest difference between the target torque
35、(Tt) and the (Ts) settled torque. Ta= (Tt Ts)/Tt Peak Overshoot (Mp): Defined as the percentage difference between the peak measured torque and the settled torque value (If target torque value is not reached, then there is no peak overshoot) Engagement Rise Time (tr): Defined as the time from 10% to
36、rque, to when the actual measured torque level has reached 90% of the target torque value System Engagement Response time (tsr): Defined as time from receipt of target torque request, to when the torque level (measured) has reached 90% of the target torque value. Initial target torque value = 0 Nm T
37、ime to Peak Torque (tp): Defined as the time from the digital request to when peak torque occurs SAE J3011 Issued OCT2012 Page 8 of 18 Settling Time (ts): Defined as the time from 10% torque to the time to reach and stay within 2% of the settled torque for 500 ms Fall Time (powered): Defined as the
38、time required from the command of 0 Nm within the settled torque region to when the torque level has reached 75 Nm Fall Time (loss of power): Defined as the time required from the initialization of loss of power within the settled torque region to 75 Nm. Applicable when there is a loss of power and
39、active torque control is not possible TABLE 1 10. DYNAMIC RESPONSE PROFILE The purpose of this test is to characterize and assess the coupling systems capability to respond to a rapidly changing request signal. The data will define the systems frequency response performance.The Swept Sine method fac
40、ilitates the calculation of a transfer function for the AWD coupling to be used in conjunction with simulation programs by OEMs/suppliers to aid in system specification and coupling selection. 10.1 Swept Sine: This test is related to non-homogenous vehicle surfaces such as transitioning from ice to
41、snow to pavement. It also encompasses the interaction of the vehicles stability system with AWD function (request for torque).SAE J3011 Issued OCT2012 Page 9 of 18 When reacting to a swept sine input coupling request function, the coupling test rig set up shall be configured as outlined in Figure 2,
42、 as described above. Due to high energy exerted during this test, thermal compensation is required to keep the results consistent. The test shall consist of calculating a transfer function of the coupling, and the reacted torque phase angle. The Transfer Function is defined by dividing the FFT of th
43、e delta torque by the FFT of the coupling request message, as shown in Equation 1. ()questCouplingfftueOutputTorqfftnctionTransferFuRe=(Eq. 1) The test shall conform to the following system control response characteristics: Exponential frequency sweep from 0.2 - 5Hz Report data in Table 2 up to 3Hz,
44、 and graph up to 5 Hz. Average torque target to be 55% of rated torque capacity Range of torque request to be 30-80% of rated torque capacity Delta speeds: 5, 50 and 100 RPM. Operating coupling temperatures (0, 20, 100 C.)10.2 Parameters for Testing The exponential frequency input parameters require
45、d to conduct the testing are listed. The swept sine coupling request function will rise according to the exponential instant frequency equation as shown below in Figure 6. FIGURE 6 Sampling rate: 256 Hz Length of test: 90 sec SAE J3011 Issued OCT2012 Page 10 of 18 Start Frequency: 0.2 Hz End Frequen
46、cy: 5.0 Hz Sweep rate: 12 Time(x) = 1 / Sampling Rate: 90 s Constant, (a) = (End Freq-Start freq) / (exp ( Length of test / Sweep rate) Inst Frequency = a*(exp(Time(x)/Sweep rate) + Start frequency The equations governing the coupling torque request are outlined below. Figure 7 shows the graphical r
47、epresentation of the requested torque. FIGURE 7 Frequency Response f(x) = Sine Amplitude*(Sine(Time (x)*2Pi * Instant frequency) Maximum sine signal: 80% Minimum sine signal: 30% Sine Amplitude = (Max sine signal - Min sine signal) / 2 The results of the test shall be reported as outlined below. The
48、 results shall be tabulated in a matrix shown in Table 2 as well as in a graphical form in Figure 8.Please note, the data is to be run at three rotational speeds, 5, 50 and 100 rpm. The data is then entered into one graph up to 5 Hz. 0.2 5 Hz sweep SAE J3011 Issued OCT2012 Page 11 of 18 TABLE 2 - TRANSFER FUNCTION RESULTS FIGURE 8 10.3 Phase Angle Measurement: Phase angle measurement is defined by a phase shift between the commanded sinusoidal input and the reacted torque. Typically with increased frequency, the reacted torque phase angle will lag the command input. The amount
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1