SAE MA 2096C-2004 Fitting End 24 degree Cone Bulkhead Design Standard Metric《24度锥角沉头配件端设计标准(米制)》.pdf

1、 METRIC AEROSPACE STANDARD (R) FITTING END, 24 CONE, BULKHEAD, DESIGN STANDARD, METRIC MA2096 Copyright 2004 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoco

2、pying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1985-08REAFFIRMED 2001-12REVISED 2004-08

3、 THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B REV. C FEDERAL SUPPLY CLASS4730 MA2096 SHEET 1 OF 3 REV.C PROCUREMENT SPECIFICATION: NONE /2/SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences. Theuse ofthisreporti

4、sentirelyvoluntary, andits applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelled.SAE invites yourw

5、ritten commentsandsuggestions. FIGURE 1 - FITTING END DESIGN, STYLE S FIGURE 2 - FITTING END DESIGN, STYLE E SAME AS STYLE S EXCEPT AS SHOWN Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-METRIC AER

6、OSPACE STANDARD (R) FITTING END, 24 CONE, BULKHEAD, DESIGN STANDARD, METRIC MA2096 REV. C MA2096 SHEET 2 OF 3 REV.C TABLE 1 - DIMENSIONS BASIC NO. MA2096 /11/ SIZE CODE (NOMINAL TUBE SIZE DN) /1/ T THREAD PER MA1370 (ISO 5855-3) 4g6g B 0 0.5 C D E F 0.2 05 5 MJ 10 X 1 8.6 4.3 0.9 6.5 22.0 06 6 MJ 12

7、 X 1.25 10.2 5.3 1.1 7.5 22.0 08 8 MJ 14 X 1.5 11.9 7.1 1.3 9.5 24.0 10 10 MJ 16 X 1.5 13.9 9.1 1.3 11.5 25.0 12 12 MJ 18 X 1.5 15.9 10.9 1.3 13.5 25.0 14 14 MJ 20 X 1.5 17.9 12.5 1.3 15.5 25.0 16 16 MJ 22 X 1.5 19.9 14.5 1.3 17.5 25.0 20 20 MJ 27 X 1.5 24.9 18.1 1.3 21.5 25.0 25 25 MJ 33 X 1.5 30.9

8、 22.5 1.3 26.6 26.0 32 32 MJ 42 X 2 39.3 29.3 1.7 33.7 29.0 40 40 MJ 50 X 2 47.3 37.3 1.7 41.7 29.0 TABLE 1A - DIMENSIONS BASIC NO. MA2096 /11/ SIZE CODE G 0.05 L 0.2 M 0 0.3 R 1.0 S 0 0.3 U V Z 0.12 AA 0.076 05 5.31 2.2 10.2 5.5 14.0 0.13 0.13-0.25 4.30 5.80 06 6.31 2.7 12.2 5.5 17.0 0.13 0.25-0.40

9、 4.80 6.30 08 8.31 3.2 14.2 6.0 19.0 0.25 0.25-0.40 4.80 6.30 10 10.31 3.2 16.2 6.0 22.0 0.25 0.25-0.40 4.80 6.30 12 12.31 3.2 18.2 6.0 24.0 0.25 0.25-0.40 4.90 7.30 14 14.31 3.2 20.2 6.0 27.0 0.25 0.25-0.40 4.90 7.30 16 16.31 3.2 22.2 6.0 30.0 0.25 0.25-0.40 4.90 7.30 20 20.33 3.2 27.2 6.0 36.0 0.2

10、5 0.25-0.40 4.90 7.30 25 25.33 3.2 33.2 6.0 41.0 0.40 0.50-0.70 4.90 7.30 32 32.35 4.2 42.2 7.0 50.0 0.40 0.50-0.70 5.40 7.80 40 40.35 4.2 50.2 7.0 60.0 0.40 0.50-0.70 5.40 7.80 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted wi

11、thout license from IHS-,-,-METRIC AEROSPACE STANDARD (R) FITTING END, 24 CONE, BULKHEAD, DESIGN STANDARD, METRIC MA2096 REV. C MA2096 SHEET 3 OF 3 REV.C NOTES: /1/ DN = NOMINAL TUBE OUTSIDE DIAMETER. /2/ THIS FITTING END IS INTENDED FOR USE WITH 24 CONE FITTINGS PER MA2005 (ISO 7169). 3. THREAD GAGI

12、NG SHALL BE PER MA1566. 4. INTERPRETATION OF DRAWING PER MAP4296. 5. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT

13、 OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. 6. INVENTORIED PARTS WITH FITTING ENDS CONFORMING ONLY TO THE PREVIOUS REVISION “A“ OF THIS STANDARD MAY BE USED TO DEPLETION. FITTING ENDS CONFORMING TO PREVIOUS REVISION “N/C“ OR “B“ MUST NOT BE USED. 7. SURFACE TEXTURE: SYMBOLS

14、 PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 3.2 m Ra. 8. BREAK EDGES PER 0.07 MAXIMUM UNLESS OTHERWISE SPECIFIED. 9. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 10. DIMENSIONS IN MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS 0.1, ANGULAR DIMENSIONS 030. /11/ EXAMPLE OF DRAWING CALLOUT: a. TABULATED PART DRAWING: FITTING END PER MA2096 b. INDIVIDUAL PART DRAWING: Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-