SAE MA 2102A-2004 HOSE ASSEMBLY METAL MEDIUM PRESSURE FLARELESS WELDED STRAIGHT TO 45 ITTING ENDS METRIC《米制、直的至45度接头端、焊接、中等压力非扩口、金属软管组件》.pdf

1、 AEROSPACE STANDARD HOSE ASSEMBLY, METAL, MEDIUM PRESSURE, FLARELESS, WELDED, STRAIGHT TO 45 FITTING ENDS, METRIC MA2102Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect

2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 198

3、9-10REVISED 2004-11 REAFFIRMED 2015-04THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3D (SEE NOTE 7) REV.A FEDERAL SUPPLY CLASS 4720MA2102 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: MA2100SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalan

4、dengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,

5、reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/MA2102A RATIONALE MA2102A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FI

6、GURE 1 TABLE 1 D HOSE ASSY PART NUMBER HOSE ASSY SIZE (DN)1THREAD T PER MA1370 4H5H A1MAX MM A2MAX MM B GAGE DIA BASIC C DIA THRU MIN MM MIN MM MAX MM E ENVELOPE DIA MM F HEX (REF) MM R RAD (REF) MM MA2102E MA2102G MA2102H MA2102J MA2102K MA2102M MA2102N DN06 DN08 DN12 DN16 DN20 DN25 DN32 MJ12X1.25

7、MJ14X1.5 MJ18X1.5 MJ22X1.5 MJ27X1.5 MJ33X1.5 MJ42X2 31.8 35.1 39.6 44.5 49.3 53.9 60.5 41.2 47.8 53.9 60.5 68.3 81.0 93.7 7.5 9.5 13.5 17.5 21.5 26.5 33.5 3.35 6.50 8.76 10.92 14.4 19.3 23.4 12.5 13.7 17.0 21.1 21.8 22.9 23.9 15.5 18.5 23.4 27.4 28.2 29.2 33.5 22.9 30.5 33.0 38.1 44.2 58.4 72.4 14 1

8、7 22 27 32 41 46 6.4 9.5 12.7 15.9 19.0 25.4 31.8 1DN = NOMINAL TUBE OUTSIDE DIAMETER TABLE 2 HOSE 21 C (70 F) CORRECTION FACTOR MM (SEE NOTE 2) HOSE SIZE (DN) NOM ID MIN MM OD MAX MM OPERATING PRESSURE MAX KPA PROOF PRESSURE MIN KPA BURST PRESSURE MIN KPA BALL SIZE MM (SEE NOTE 5) STRAIGHT FITTING

9、45 DEG FITTING 06 08 12 16 20 25 32 5.5 7.0 11.0 14.0 17.5 23.0 30.0 11.0 13.5 20.5 24.0 29.0 36.0 44.0 13 750 12 000 9 800 8 300 7 200 5 500 3 800 20 650 18 000 14 500 13 400 10 700 8 300 5 700 55 150 48 000 38 600 33 000 29 000 22 000 15 200 3 6 8 10 14 18 22 4.1 4.5 4.8 5.0 5.8 7.6 9.4 2.8 2.8 2.

10、8 2.8 2.8 2.8 3.2 AEROSPACE STANDARD MA2102 SHEET 2 OF 2 REV. A HOSE ASSEMBLY, METAL, MEDIUM PRESSURE, FLARELESS, WELDED, STRAIGHT TO 45 FITTING ENDS, METRIC TABLE 3 HOSE ASSEMBLY LENGTH AVAILABLE LENGTH INCREMENT LENGTH TOLERANCE UNDER 457 MM 457 TO 914 MM 914 TO 1270 MM OVER 1270 MM (NOT LESS THAN

11、) 3 MM (NOT LESS THAN) 7 MM (NOT LESS THAN) 13 MM (NOT LESS THAN) 26 MM 3 MM 7 MM 13 MM 1% CONSTRUCTION AND PERFORMANCE: THESE HOSE ASSEMBLIES SHALL MEET THE CONSTRUCTION AND PERFORMANCE REQUIREMENTS OF MA2100 (ISO/DIS7314). OPERATING CHARACTERISTICS: SEE PROCUREMENT SPECIFICATION. MATERIALS AND FIN

12、ISH: 321 OR OTHER CORROSION RESISTANT STEEL, PASSIVATED, IN ACCORDANCE WITH THE PROCUREMENT SPECIFICATION. IDENTIFICATION: SEE MA2100, 3.7 PROCUREMENT SPECIFICATION: MA2100 (ISO/DIS7314) NOTES: 1. LENGTH “L“ IS MEASURED FROM GAGE POINT TO GAGE POINT. SEE TABLE 3 FOR AVAILABLE LENGTH INCREMENTS. IN T

13、HE EXAMPLE OF PART NUMBER BELOW, LENGTH “L“ IS DEFINED BY A FOUR DIGIT DASH NUMBER DESCRIBING THE HOSE ASSEMBLY LENGTH IN MM. 2. TO CONVERT “GAGE POINT TO GAGE POINT“ TO “END TO END“ MEASUREMENT, ADD TO “L“ THE APPROPRIATE TABLE 2 CORRECTION FACTOR FOR EACH END FITTING. 3. THE HOSE ASSEMBLIES ARE IN

14、TENDED FOR USE IN LOW AND MEDIUM PRESSURE PNEUMATIC SYSTEMS UP TO 425 C WITH SHORT DURATION EXCURSIONS TO 650 C. MAXIMUM RATED OPERATING PRESSURE IS DEPENDENT ON AMBIENT OPERATING TEMPERATURE AND CAN BE DETERMINED FROM MA2100, TABLE 2. 4. DIMENSIONS IN MM. DIMENSIONING AND TOLERANCING ARE PER ANSI Y

15、14.5M AND UNIT SYMBOLS ARE PER ANSI Y10.19, SAE J916 AND ANSI Z210.1. 5. A TRUE CIRCULAR CROSS SECTION IS NOT REQUIRED THROUGH THE END FITTING. HOWEVER, A BALL OF THE SIZE DIAMETER LISTED IN TABLE 2 SHALL PASS THROUGH THE END FITTING AFTER THE END FITTING IS ATTACHED TO THE HOSE ASSEMBLY. 6. DO NOT

16、USE UNASSIGNED SIZE CODES. 7. CHANGES TO THIS STANDARD DRAWING SHALL BE COORDINATED WITH SAE COMMITTEE E-25, GENERAL STANDARDS FOR AEROSPACE AND PROPULSION SYSTEMS. 8. EXAMPLE OF PART NUMBER: 9. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.