SAE MA 2119B-2013 ADAPTER ASSEMBLY - PORT CONNECTION RING LOCKED TO 60 LARELESS TUBE END METRIC《端口连接环锁定到60度非扩口管末端公制接头组件》.pdf

1、METRIC AEROSPACE STANDARD ADAPTER, ASSEMBLY - PORT CONNECTION RING LOCKED TO 60 FLARELESS TUBE END, METRIC MA2119Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic,

2、mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1992-06REA

3、FFIRMED 2004-07 REVISED 2013-04THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B /5/ REV.BFEDERAL SUPPLY CLASS 4730 MA2119SHEET 1 OF 3REV. BPROCUREMENT SPECIFICATION: /4/ MA2005 (ISO 7169)SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengi

4、neering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed

5、, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/MA2119BRATIONALE HARMONIZE STANDARD TO AECMA EN3248 EQUIVALENT STANDARD RELATED TO FINISH OF THE FITTING BODY

6、; ADD AMS5732, AMS5737 AND AMS5853 OPTION FOR A286 LOCKRING MATERIAL AND OTHER GENERAL UPDATES. FIGURE 1 - ADAPTER, ASSEMBLY TABLE 1A - DIMENSIONS A THROUGH G BASIC NO. MA2119 /18/SIZE CODE ATHREADMA1370 (ISO 5855) BTHREADMA1370 (ISO 5855) C0.09 (D) E+0.20/0F+0.15/-0.05 GMIN08-06 MJ12 x 1.25-4g6g MJ

7、10 x 1-4h6h 17.80 5.00- 5.20 6.10 8.50 11.0610-06 MJ12 x 1.25-4g6g MJ12 x 1.25-4h6h 19.50 5.00- 5.20 7.70 10.20 12.7810-08 MJ14 x 1.5-4g6g MJ12 x 1.25-4h6h 19.50 6.70- 6.90 7.70 10.20 12.7812-06 MJ12 x 1.25-4g6g MJ14 x 1.5-4h6h 21.00 5.00- 5.20 9.00 11.90 14.3812-08 MJ14 x 1.5-4g6g MJ14 x 1.5-4h6h 2

8、1.00 6.70- 6.90 9.00 11.90 14.3812-10 MJ16 x 1.5-4g6g MJ14 x 1.5-4h6h 21.00 8.70- 8.90 9.00 11.90 14.3814-06 MJ12 x 1.25-4g6g MJ16 x 1.5-4h6h 22.60 5.00- 5.20 10.70 13.90 16.3614-08 MJ14 x 1.5-4g6g MJ16 x 1.5-4h6h 22.60 6.70- 6.90 10.70 13.90 16.3614-10 MJ16 x 1.5-4g6g MJ16 x 1.5-4h6h 22.60 8.70- 8.

9、90 10.70 13.90 16.3614-12 MJ18 x 1.5-4g6g MJ16 x 1.5-4h6h 22.60 10.60-10.80 10.70 13.90 16.36IDENTIFICATION LOCATION OPTIONAL /8/METRIC AEROSPACE STANDARD MA2119SHEET 2 OF 3REV. B ADAPTER, ASSEMBLY - PORT CONNECTION RING LOCKED TO 60 FLARELESS TUBE END, METRIC TABLE 1B - DIMENSIONS H THROUGH N BASIC

10、 NO. MA2119 /18/SIZE CODE H0.2 J0.15 K+0.50/0 (L) M0.40 N0.20 08-06 25.2 8.75 9.30 13.87 16.15 7.00 10-06 25.2 8.75 10.00 15.37 16.70 7.00 10-08 27.0 10.55 10.00 15.37 16.70 7.00 12-06 25.2 8.75 10.65 17.12 17.45 7.00 12-08 27.0 10.55 10.65 17.12 17.45 7.00 12-10 27.0 10.55 10.65 17.12 17.45 7.00 14

11、-06 25.2 8.75 11.30 18.77 17.90 7.00 14-08 27.0 10.55 11.30 18.77 17.90 7.00 14-10 27.0 10.55 11.30 18.77 17.90 7.00 14-12 27.0 10.55 11.30 18.77 17.90 7.00 NOTES: 1. MATERIAL a. FITTING: 6Al-4V TITANIUM ALLOY PER AMS4928, AMS4965, OR AMS4967. b. LOCKRING: A286 CORROSION RESISTANT STEEL PER AMS5731,

12、 AMS5732, AMS5734, AMS5737, OR AMS5853. 2. HEAT TREATMENT: a. FITTING: 900 MPa UTS MIN b. LOCKRING: 34-40 HRC 3. FINISH: a. FITTING: ANODIC TREATMENT PER AMS2488, TYPE 2 ON ALL SURFACES AND SOLID FILM LUBE PER AS5272, TYPE I ON ALL SURFACES EXCEPT IN THE FLOW HOLE. ALTERNATE FINISH: SOLID FILM LUBE

13、PER AS5272, TYPE I ON ALL SURFACES EXCEPT IN THE FLOW HOLE. b. LOCKRING: PASSIVATE PER AMS2700, TYPE 2. /4/ PROCUREMENT SPECIFICATION: MA2005 (ISO 7169) EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUAFCTURED BY AN ACCREDITED MANUFACTURER LISTED IN PERFORMA

14、NCE REVIEW INSTITUTE (PRI) QUALIFIED MANUFACTURER LIST (QML) FOR THIS TYPE PRODUCT. THE QML IS AVAILABLE AT www.eAuditN./5/ AECMA INTEREST: FUTURE REVISIONS TO THIS STANDARD SHALL BE COORDINATED WITH AECMA C4 COMMITTEE. AECMA IS ASSOCIATION EUROPEENNE DES CONSTRUCTEURS DE MATERIEL AEROSPATIAL (PARIS

15、, FRANCE). /6/ SEALING SURFACE: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT. /7/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT. LOCKRING EXTERNAL SERRATION DELETED ONE TOOTH FOR METRIC IDENTIFICATION PURPOSE. 8. IDENTIFICATION: a. MARK AT LOCATION(S) SHOWN PER AS478 METHOD 2 OR 15

16、, MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE. b. MARK PER AS478 CLASS 35D, MANUFACTURERS NAME, TRADEMARK OR CAGE CODE AND PART NUMBER. METRIC AEROSPACE STANDARD MA2119SHEET 3 OF 3REV. B ADAPTER, ASSEMBLY - PORT CONNECTION RING LOCKED TO 60 FLARELESS TUBE END, METRIC 9. WORKING PRESSURE: THIS PART I

17、S DESIGNED FOR USE IN 28 000 kPa WORKING PRESSURE SYSTEMS COMPATIBLE WITH TITANIUM. 10. ADAPTERS TO BE INSTALLED PER MA2114 INTO BOSS CAVITIES PER MA2110. 11. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 12. INTERPRETATION OF DRAWING PER MAP4296. 13. SURFACE

18、 TEXTURE: SYMBOLS PER ANSI Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 3.2 MICROINCHES Ra AND SEALING SURFACE TO BE 1.6 MICROINCHES Ra. 14. BREAK EDGES 0.08 TO 0.38 UNLESS OTHERWISE SPECIFIED. 15. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 16. DIMEN

19、SIONS IN MILLIMETERS. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS 0.13, ANGULAR DIMENSIONS 5 DEGREES. /17/ FITTING END IN ACCORDANCE WITH AECMA STANDARD EN2604. /18/ EXAMPLE OF PART NUMBER: 19. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING A

20、REAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.