ImageVerifierCode 换一换
格式:PDF , 页数:22 ,大小:144.74KB ,
资源ID:1028176      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-1028176.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(SAE MA 620-1998 Hose Assemblies Convoluted Polytetrafluoroethylene Metallic Reinforced High Temperature Medium Pressure Aircraft Metric《公制盘旋状聚四氟乙烯金属加固的高温中压飞机软管组件》.pdf)为本站会员(eastlab115)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

SAE MA 620-1998 Hose Assemblies Convoluted Polytetrafluoroethylene Metallic Reinforced High Temperature Medium Pressure Aircraft Metric《公制盘旋状聚四氟乙烯金属加固的高温中压飞机软管组件》.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/MA620 AEROSPACE STANDARD MA620 Issued 1998-03 Reaffirmed 2015-07 Hose Assemblies,

5、 Convoluted Polytetrafluoroethylene Metallic Reinforced, High Temperature, Medium Pressure, Aircraft Metric RATIONALE MA620 has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE :This SAE Aerospace Standard (MA) defines the requirements for a convoluted polytetrafluoroethylene

6、 (PTFE) lined, metallic reinforced, hose assembly suitable for use in aircraft fluid systems at temperatures of -55 to 204 C and at operating pressures per Table 1.TABLE 1 - Physical Requirements of Hose Assemblies and Weight of HoseHoseSizeDNHoseWeightMax 1kg/mOperatingPressureMaxkPaProofPressureMa

7、xkPaBurstPressureRoomT emperatureMinkPaBurstPressureHighTemperatureMinkPaBend RadiusAt Inside ofBend Minmm06 0.143 6900 13 800 27 600 19 300 3210 0.179 6900 13 800 27 600 19 300 5712 0.268 6900 13 800 27 600 19 300 7316 0.357 6900 12 410 24 820 17 240 7620 0.483 6900 12 410 24 820 17 240 9525 0.590

8、6900 12 410 24 820 17 240 12732 0.893 6900 12 410 24 820 17 240 15940 1.071 5170 10 340 20 700 14 480 19150 1.607 1720 3 440 6 900 4 820 25463 1.964 689 1 380 2 760 1 930 31876 2.589 689 1 380 2 760 1 930 381101 3.572 689 1 380 2 760 1 930 6101 Hose weight shall be determined on a minimum length of

9、305 mm.SAE INTERNATIONAL MA620 Page 2 of 22 1.1 Types :1.1.1 Hose assemblies furnished under this document may be of two types:Type I - Non-conductive Inner TubeType II - Conductive Inner Tube1.1.2 Hose assemblies furnished under this document may be of the following classes. If no class is defined

10、then Class 1 shall prevail.Class 1 - Liquid Proof T estClass 2 - Liquid and Pneumatic Proof Test2. REFERENCES :2.1 Applicable Documents :The following publications form a part of this specification to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue

11、 of other publications shall be the issue in effect on the date of purchase order. In the event of conflict between the text of this specification and references cited herein, the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regu

12、lations unless a specific exemption is obtained.2.1.1 SAE Publications : Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.AMS 5556 Steel, Corrosion and Heat Resistant, Seamless or Welded Tubing, 18Cr 11Ni 0.70(Cb+ Ta) (SAE 30347), Hydraulic, Solution Heat TreatedAMS 5557 Steel T

13、ubing, Seamless and Welded, Corrosion and Heat Resistant, 18.5Cr 10.5Ni 0.40Ti (SAE 30321), Hydraulic, Solution Heat TreatedAMS 5567 Steel Tubing, Seamless or Welded, Corrosion Resistant, 19Cr 10Ni (SAE 30304), Hydraulic, AnnealedAMS 5570 Steel, Corrosion and Heat Resistant, Seamless Tubing, 18Cr 11

14、Ni 0.40Ti (SA E 30321), Solution Heat TreatedAMS 5571 Steel, Corrosion and Heat Resistant, Seamless Tubing, 18Cr 10.5Ni 0.70(Cb+ Ta) (SAE 30347), Solution Heat TreatedAMS 5575 Steel, Corrosion and Heat Resistant, Welded Tubing, 18Cr 10.5Ni 0.70(Cb+ T a) (SA E 30347), Solution Heat TreatedAMS 5636 St

15、eel, Corrosion Resistant, Bars and Wire, 18Cr 9.0Ni (SAE 30302) Solution Heat Treated and Cold Drawn, 100 ksi T ensile StrengthAMS 5637 Steel, Corrosion Resistant, Bars and Wire, 18Cr 9.0Ni (SAE 30302) Solution Heat Treated and Cold Drawn, 125 ksi T ensile StrengthAMS 5639 Steel Bars, Wire, Forgings

16、, Tubing and Rings, Corrosion Resistant, 19Cr 10Ni (SA E 30304), Solution Heat TreatedAMS 5643 Steel, Corrosion Resistant, Bars, Wire, Forgings, Tubing and Rings, 16Cr 4.0Ni 0.30(Cb+ Ta) 4.0Cu (SAE 17-4PH), Solution Heat Treated, Precipitation HardenableAMS 5644 Steel Bars and Forgings, Corrosion Re

17、sistant, 17Cr 7.0Ni 1.0Al (SAE 17-4PH)SAE INTERNATIONAL MA620 Page 3 of 22 2.1.1 (Continued):AMS 5645 Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing and Rings, 18C r 10Ni 0.40Ti (SAE 30321), Solution Heat TreatedAMS 5646 Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, T

18、ubing and Rings, 18C r 11Ni 0.60(Cb+ T a) (SAE 30347), Solution Heat TreatedAMS 5656 Steel, Corrosion Resistant, Bars, Wire, Forgings, Extrusions and Rings, 9.0Mn 20Cr 6.5Ni 0.27N (SAE 21-6-9), Solution Heat TreatedAMS 5659 Steel, Corrosion Resistant, Bars, Wire, Forgings, Rings and Extrusions, 15Cr

19、 4.5Ni 0.30Cb 3.5Cu (SAE 15-5PH), Consumable Electrode Melted, Solution Heat Treated, Precipitation HardenableAMS 5688 Steel, Corrosion Resistant, Wire, 18Cr 9.0Ni (SAE 30302) Spring T emperAMS 5689 Steel, Corrosion and Heat Resistant, Wire 18Cr 10.5Ni 0.40Ti (SAE 30321), Solution Heat TreatedAMS 56

20、90 Steel, Corrosion and Heat Resistant, Wire 17Cr 12Ni 2.5Mo (SAE 30316), Solution Heat TreatedAMS 5697 Steel, Corrosion Resistant, Wire 19Cr 9.5Ni (SAE 30304), Solution Heat TreatedAS150 Hose Assembly, Type Classifications of, Basic Performance and Fire ResistanceAS611 T etrafluoroethylene Hose Ass

21、embly Cleaning MethodsARP908 Hose and Tube Fitting - Installation and Qualification Test T orqueAS1055 Fire Testing of Flexible Hose, Tube Assemblies, Coils, Fittings and Similar System ComponentsARP1835 Preparation for Delivery General Requirements for Hose AssembliesMA1370 Screw Threads, MJ Profil

22、e, MetricMA2078 T est Methods, Hose Assemblies, Polytetrafluoroethylene (PTFE)MA2014 Fitting End, Flareless Acorn, MetricMA2095 Fitting Design Standard, 24 degree Cone, Metric2.1.2 ASTM Publications : Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.ASTM A 262 Standard Re

23、commended Practices for Detecting Susceptibility to Intergranular Attack in Stainless SteelASTM A 313 Standard Specification for Stainless Steel Spring WireASTM A 580 Specification for Stainless and Heat Resisting Steel WireSAE INTERNATIONAL MA620 Page 4 of 22 2.1.3 U.S. Government Publications : Av

24、ailable from DODSS P , Subscription Services Desk, Buildin g 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.P-D-680 Dry Cleaning SolventQQ-S-763 Steel Bars, Wire Shapes, and Forgings, Corrosion-ResistingQQ-P-35 Passivation Treatments for Corrosion-Resistant SteelsTT-I-735 Isopropyl AlcoholTT-S-

25、735 Standard Test Fluids, HydrocarbonsMIL-C-5501 Caps and Plugs, Protective, Dust and Moisture Seal, General SpecificationMIL-H-5606 Hydraulic Fluid, Petroleum Based, Aircraft, Missile and OrdnanceMIL-T-5624 Turbine Fuel, Aviation, Grades JP-4 and JP-5MIL-L-7808 Lubricating Oil, Aircraft Turbine Eng

26、ine, Synthetic BaseMIL-T-8504 Tubing, Steel, Corrosion-Resisting (304) Aerospace Vehicle, Hydraulic Systems, Annealed, Seamless and WeldedMIL-T-8808 Tubing, Steel, Corrosion-Resistant (18-8 Stabilized), Aircraft Hydraulic QualityMIL-H-83282 Hydraulic Fluid, Fire Resistant Synthetic Hydrocarbon Base,

27、 AircraftMIL-STD-100 Engineering Drawing PracticesMIL-STD-130 Identification Marking of U.S. Military PropertyMIL-STD-831 T est Reports, Preparation of2.1. 4 ASME Publications : Available from ASME, 345 E. 47th Street, New York, NY 10017.ANSI/ASME B46.1 Surface T exture2.2 Hose Assembly Procurement

28、Specifications :Refer to MA620SUP1 for a listing of applicable hose assembly procurement standards applicable to this document.3. TECHNICAL REQUIREMENTS :3.1 Qualification :The hose assemblies furnished under this specification shall be products which are qualified by meeting all the requirements co

29、vered by this document.3.2 Material :The hose assembly materials shall be uniform in quality, free from defects, consistent with good manufacturing practice and shall conform to applicable specifications and the requirements specified herein. All materials not specifically described herein shall be

30、of the highest quality and suitable for the purpose intended.SAE INTERNATIONAL MA620 Page 5 of 22 3.2.1 Metals :Metals used in the hose and fittings shall be corrosion-resistant and shall conform to the following specifications:Bars and Forgings:QQ-S-763 Class 304 - Cond. A or Cond. B (AMS 5639)QQ-S

31、-763 Class 302 - Cond. A or Cond. B (AMS 5636 or AMS 5637)QQ-S-763 Class 321 - Cond. A (AMS 5645)QQ-S-763 Class 347 - Cond. A (AMS 5646)AMS 5643 17-4PHAMS 5644 17-7PHAMS 5656 21-6-9AMS 5659 15-5PHTubing:MIL-T-8504 Comp. 304 (AMS 5567)MIL-T-8808 Type I or Type II, Comp. 321 (AMS 5570 or AMS 5557)MIL-

32、T-8808 Type I or Type II, Comp. 347 (AMS 5571, AMS 5575 or AMS 5556)Wire:ASTM A 580/A 313 Comp. 302 (AMS 5688)ASTM A 580/A 313 Comp. 304 (AMS 5697)ASTM A 580/A 313 Comp. 316 (AMS 5690)ASTM A 580/A 313 Comp. 321 (AMS 5689)3.3 Construction :The hose assembly shall consist of a convoluted polytetrafluo

33、roethylene inner tube, which may be covered with convoluted woven glass cloth and/or other suitable materials, corrosion-resistant steel-wire reinforcement, and corrosion-resistant steel end fittings as required to meet the construction and performance requirements of this document and as required f

34、or its intended use.3.3.1 Inner Tube :The inner tube shall be of a convoluted construction of virgin polytetrafluoroethylene resin designed to promote easy bending. It shall be free from pitting or projections on the inner surface. Additives may be included in the compound from which the tube is fab

35、ricated.3.3.2 Reinforcement :The reinforcement shall consist of corrosion-resistant steel wires conforming to the applicable specifications listed in 3.2.1. The wires shall be so arranged over the inner tube as to provide sufficient strength to ensure conformance with the requirements specified here

36、in. Broken reinforcing wires shall be cause for rejection. Crossed-over reinforcing wires shall not be cause for rejection of the hose assembly.SAE INTERNATIONAL MA620 Page 6 of 22 3.3.3 Interlayers :Interlayers, if used, shall be of a suitable material and shall be resistant to all fluids with whic

37、h the hose may come in contact during normal service. They shall be capable of withstanding temperatures of -55 to 204 C and shall not extrude through the outer braid during testing or in service.3.3.4 Fittings :All fittings shall be permanently attached and proven to meet the requirements herein. S

38、tandard hose assemblies shall have flared fittings to meet MA2095, flareless fittings according to MA2014 in accordance with applicable documents (see 2.1). Fitting hex portions shall fit standard wrench openings.3.3.4.1 Straight Fittings :Fittings shall be of one-piece construction. Weld or braze j

39、oints must not be located in the fluid paths, except welded and redrawn tubing per MIL-T-8504 or MIL-T-8808 may be used.3.3.4.2 Other Fittings :Other fittings, including elbow fittings, shall be of one piece construction to the maximum extent possible. When one piece construction is not used, the jo

40、ints shall be welded using either butt-weld or lap-weld design. For double elbow assemblies, the elbows may be treated as non-standard.3.3.4.3 End Fitting Collars (Sockets) : All end fitting collars (sockets) crimped or swaged, fabricated from Type 304 stainless steel are required to be capable of p

41、assing an embrittlement test as specified in ASTM A 262 Practice E, prior to assembly to the nipple or swaging operation. Sockets fabricated from stabilized austenitic steel (304L, 321 or 347) are acceptable without being subjected to the embrittlement test.3.3.4.4 Fitting Finish :3.3.4.4.1 Corrosio

42、n-Resistant Steel Parts : Unless otherwise specified, corrosion resistant steel parts shall be passivated in accordance with QQ-P-35.3.4 Dimensions :The hose assembly dimensions, except for length, shall be as specified in Figure 1 and T able 2.1 Cross corners of nut and socket hex may exceed “D” di

43、mensions.FIGURE 1 - Hose and Fitting DimensionsSAE INTERNATIONAL MA620 Page 7 of 22 TABLE 2 - Hose and Fitting DimensionsHoseSizeDNRigidTubing ODRefmmFitting IDMinA 1mmHose IDMinBmmHose WireBraid ODCmm 0.81Fitting ODMaxDmm06 6.35 3.35 6.86 11.30 14.010 9.53 6.50 9.02 14.10 17.312 12.70 8.76 12.95 19

44、.18 21.816 15.88 10.92 15.24 21.60 24.120 19.05 16.12 19.43 26.92 32.525 25.40 21.21 24.89 32.97 37.332 31.75 27.56 30.99 38.76 43.240 38.10 33.27 37.59 45.47 50.850 50.80 46.36 49.20 59.26 65.063 63.50 57.86 61.90 73.03 76.276 76.20 70.38 74.46 87.12 94.0101 101.60 93.98 100.00 113.16 119.41 Hose a

45、ssembly conformance to minimum specified inside diameter shall be verified by passing the designated or larger spherical ball through the hose assembly.SAE INTERNATIONAL MA620 Page 8 of 22 3.4.1 Hose Weight :Hose consisting of inner tube, reinforcement and interlayers as outlined in 3.3.1 through 3.

46、3.3 shall not exceed the maximum weights specified in T able 1.3.5 Performance :The hose assembly shall meet the following performance requirements:3.5.1 Proof Pressure :3.5.1.1 Class 1 hose assemblies shall withstand the proof pressure listed in Table 1 without malfunction or leakage when tested wi

47、th water in accordance with 4.6.2.1.TABLE 3 - Minimum Inspection Ball Size for Hose Assembly 1HoseSizeDNStraight EndFittingmmElbow EndFittingmm06 3.02 2.8510 5.85 5.5312 7.88 7.4516 9.83 9.2820 14.51 13.7025 19.09 18.0332 24.80 23.4340 29.94 28.2850 41.72 39.4163 52.07 49.1876 63.34 59.82101 84.58 7

48、9.881 Hose assembly conformance to minimum specified inside diameter shall be verified by passing the designated or larger spherical ball through the hose assembly.SAE INTERNATIONAL MA620 Page 9 of 22 3.5.1.2 Class 2 hose assemblies shall meet the Class 1 proof pressure test requirement and shall wi

49、thstand 25% of the operating pressure listed in Table 1 without malfunction or leakage in excess of the normal effusion rate of one bubble per minute for each 25.4 mm of polytetrafluoroethylene (PTFE) hose length plus one bubble per minute for each end fitting when tested pneumatically in accordance with 4.6.2.2.3.5.2 Elongation and Contraction : The hose assemb

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1