SAE MS 1006-2011 Lubricants Industrial Oils and Related Products Type F Lubricant for Spindle Bearings and Associated Clutches - Specification《润滑剂 润滑油和F类相关转轴轴承润滑剂以及相关离合器规范》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2011 SAE International All rights reserved. No part of this pub

3、lication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970

4、(outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/MS1006_201112INDUSTRIALLUBRICANTSTANDARDMS1006 DEC2011 Issued 2001-07 Revised 2011-1

5、2 Superseding MS1006 JUN2001 Lubricants, Industrial Oils, and Related Products Type F Lubricant for Spindle Bearings, and Associated Clutches - Specification RATIONALEThe revision of SAE MS1006 was necessary to reflect changes to test limits, changes to test methods and additional standards that hav

6、e been incorporated since SAE MS1006 was originally released in 2001.FOREWORDThe SAE International Industrial Lubricants Committee has developed a number of industrial, non-production lubricant performance specifications.The purpose of these voluntary SAE specifications is to: a. Define minimum perf

7、ormance requirements for industrial lubricants. b. Provide lubricant suppliers with performance targets for a minimum number of key industrial lubricants. c. Improve the availability of these lubricants to member companies. d. Provide a plant oriented, user friendly, classification system using comm

8、on test standards and properties. ISO Standard 6743 - Lubricants, industrial oils and related products (class L) - Classification is the foundation for these documents.a. Performance characteristics and test procedures are specified.b. For information, equivalent ISO, DIN, CEN, BSI, ASTM, AFNOR, CET

9、OP, and IP test methods are referenced.11International Standards Organization (ISO) Deutsches Institut fur Normung e. V. (DIN) European Committee for Standardization (CEN) American Society for Testing and Materials (ASTM) Association of Francaise de Normalisation (AFNOR) The Institute of Petroleum (

10、IP) NOTE: Now combined with BSI British Standards Institution (BSI), BS 2000: XXX where XXX is the corresponding IP number European Committee on Hydraulic Oil and Pneumatics (CETOP) SAE MS1006 Revised DEC2011 Page 2 of 11 Industrial lubricant classifications targeted: a. Lubricants, Industrial Oils

11、and Related Products - Classification (SAE MS1000) b. General purpose and total loss lubricants (SAE MS1001) c. Gear oils (SAE MS1002) d. Compressor oils (SAE MS1003) e. Hydraulic fluids (SAE MS1004) f. Fire resistant hydraulic fluids (SAE MS1005) g. Lubricants for spindle bearings and associated cl

12、utches (SAE MS1006) h. Slideway lubricants (SAE MS1007) i. Metal removal fluids (SAE MS1008) j. Lubricants for pneumatic tools (SAE MS1009) k. Turbine oils (SAE MS1010) l. Lubricating greases (SAE MS1011) See SAE MS1000 - Index of lubricants and symbols. NOTE: Environmental, Technical Reports, and/o

13、r health and safety regulations may present additional specifications to the supplier. SAE MS1006 Revised DEC2011 Page 3 of 11 1. SCOPE See Table 1. TABLE 1 - SCOPE AND FIELD OF APPLICATIONS Code letter GeneralApplicationsMore specific applications Composition and properties Symbol Typical Applicati

14、ons F Spindle bearings, bearings, and associatedclutches.Spindle bearings, bearings, and associatedclutches.Refined mineral oils with improved anti-corrosion and anti-oxidation properties FC Typically pressure, bath and oil-mist (aerosol) lubrication of plain or rolling bearings and associated clutc

15、hes in machine tools. Note that where clutches are involved, anti-wear or EP additives should be avoided because of the risk of corrosion Spindle bearings, bearings.Refined mineral oils with improved anti-corrosion,anti-oxidation and anti-wear propertiesFD Typically pressure, bath and oil-mist (aero

16、sol) lubrication of plain or rolling bearings in machine tools 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply. 2.1.1 SAE Publications Avai

17、lable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.SAE MS1000 Lubricants, Industrial Oils and Related ProductsClassification SAE MS1001 Lubricants, Industrial Oils, and Related Products

18、 Type A Lubricant for General Purpose and Total Loss Systems - Specification SAE MS1002 Lubricants, Industrial Oils, and Related Products Type C (Gears) Specification SAE MS1003 Lubricants, Industrial Oils, and Related Products Type D Compressor OilsSpecification SAE MS1004 Lubricants, Industrial Oi

19、ls, and Related Products Type H (Hydraulic Fluids) - Specification SAE MS1005 Lubricants, Industrial Oils, and Related Products Type HF Fire-Resistant Hydraulic FluidsSpecificationSAE MS1006 Lubricants, Industrial Oils, and Related Products Type F Lubricant for Spindle Bearings, and Associated Clutc

20、hesSpecificationSAE MS1007 Lubricants, Industrial Oils, and Related Products Type G Slideway Lubricants SpecificationSAE MS1006 Revised DEC2011 Page 4 of 11 SAE MS1008 Lubricants, Industrial Oils and Related Products Type M (Metal Removal Fluids) SpecificationSAE MS1009 Lubricants, Industrial Oils,

21、and Related Products Type P Pneumatic Tool Oils SpecificationSAE MS1010 Lubricants, Industrial Oils, and Related Products Type T Turbine OilsSpecification SAE MS1011 Lubricants, Industrial Oils and Related Products - Type X (Greases)Specification2.1.2 ASTM Publications Available from ASTM Internatio

22、nal, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM D 92 Test Method for Flash and Fire Points by Cleveland Open Cup ASTM D 97 Test Methods For Pour Point Of Petroleum Products ASTM D 130 Method for Detection of Copper Corrosion from Petr

23、oleum Products by Copper Strip Tarnish Test ASTM D 445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) ASTM D 471 Test Method for Rubber Property - Effect of Liquids ASTM D 664 Test Method for Neutralization Number of Petroleum Products by

24、 Potentiometric Titration ASTM D 665B Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Synthetic Sea WaterASTM D 892 Test Method for Foaming Characteristics of Lubricating Oils ASTM D 943 Standard Test Method for Oxidation Characteristics of Inhibited Miner

25、al Oils ASTM D 974 Test Method for Acid and Base Number by Color-Indicator Titration ASTM D 1298 Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method ASTM D 1401 Test Method for Water Separability of Petrol

26、eum Oils and Synthetic Fluids ASTM D 2070 Standard Test Method for Thermal Stability of Hydraulic Oils ASTM D 2140 Test Method for Carbon-Type Composition of Insulating Oils of Petroleum OriginASTM D 2422 Classification of Industrial Fluid Lubricants by Viscosity System ASTM D 3238 Method for Calcul

27、ation of Carbon Distribution and Structural Group Analysis of Petroleum Oils by the N-D-M MethodASTM D 4052 Test Method for Density and Relative Density of Liquids by Digital Density Meter ASTM D 4172 Test Method for Wear Preventive Characteristics of Lubricating Fluid (Four-Ball Method) ASTM E 1687

28、 Standard Test Method for Determining Carcinogenic Potential of Virgin Base Oils in Metalworking FluidsSAE MS1006 Revised DEC2011 Page 5 of 11 2.1.3 Other Publications Referenced AFNOR, BS, CEN, DIN, IP and ISO Standard hardcopies are available from the SAI Global Website (http:/ BS Publications Ava

29、ilable from British Standards Institution, Customer Services, 389 Chiswick High Road, London W4 4AL, United Kingdom, Tel: +44-0-20-8996-9001, www.bsi-.BS 188 Determination of the Viscosity of Liquids BS 4231 Classification for Viscosity Grades of Industrial Liquid Lubricants BS 4832 Determination of

30、 the Behavior of Rubber and Elastomers when Exposed to Liquids, Vapors and Gases (Superseded by ISO 6072) 2.1.5 DIN Publications Available from Deutsches Institut fr Normung e.V., Burggrafenstrasse 6, 10787 Berlin, Germany, www.din.deDIN 51 519 Lubricants; ISO Viscosity Classification for Industrial

31、 Liquid LubricantsDIN 51 558/1 Testing of Mineral Oils; Determination of the Neutralization Number, Colour Indicator TitrationDIN 51 561 Testing of Mineral Oils, Liquid Fuels and Related Liquids; Measurement of Viscosity Using The Vogel-Ossag Viscometer; Temperature Range: Approximately 10 To 150-De

32、g C (CANCELLED)DIN 51 562/1 Viscometry - Determination of Kinematic Viscosity Using the Ubbelohde Viscometer - Part 1: Apparatus and Measurement ProcedureDIN 51 566 Testing of Lubricants; Determination of Foaming Characteristics (CANCELLED) DIN 51 569 Determination of Viscosity of Mineral Oils, Liqu

33、id Fuels and Related Liquids at Temperatures from 55CTo Approximately 10C Using the Vogel-Ossag Viscometer DIN 51 585 Testing of Lubricants; Testing of Corrosion Protection Properties of Steam Turbine Oils and Hydraulic Oils Containing AdditivesDIN 51 587 Testing of Lubricants; Determination of the

34、Ageing Behaviour of Steam Turbine Oils and Hydraulic Oils Containing Additives DIN 51 599 Testing of Lubricating Oils; Determination of Demulsification Capacity According to the Stirring MethodDIN 51 757 Testing of Mineral Oils and Related Materials; Determination of DensityDIN 51 759/1 Testing of L

35、iquid Mineral Oil Products; Method of Test for Copper Corrosion; Copper Strip Test (SUPERSEDED BY ISO 2160) DIN 53 505 T esting of Rubber, Elastomers, and Plastics; Shore Hardness Testing A and D DIN 53 521 Determination of the Behaviour of Rubber and Elastomers when Exposed to Fluids and Vapours DI

36、N 53 538/1 Standard Reference Elastomers; Acrylonitrile - Butadiene Rubber (NBR); Peroxide Cured for Characterizing Service Fluids with Respect to Their Action on NBR SAE MS1006 Revised DEC2011 Page 6 of 11 2.1.6 EPA Publications Standard test methods of the U. S. Environmental Protection Agency. SW

37、-846 Methods are available on-line (Website: http:/www.epa.gov/epaoswer/hazwaste/test/8xxx.htm). Method 24 available in the Code of Federal Regulations in 40 CFR, Part 60, Appendix A) EPA SW 846, Method 8082 Polychlorinated Biphenyls (PCBs) By Gas Chromatography EPA SW 846, Method 8121 Chlorinated H

38、ydrocarbons by Gas Chromatography: Capillary Column Technique EPA SW 846, Method 8270C Semivolatile Organic Compounds By Gas Chromatography/Mass Spectrometry 2.1.7 IP Publications Available from SAI as referenced above in 2.1.3. IP 15 Petroleum Products - Determination of Pour Point IP 19 Determinat

39、ion of Demulsibility Characteristics of Lubricating Oil IP 36 Determination of Open Flash and Fire Point - Cleveland Method IP 71 (Sect. 1) Petroleum Products - Transparent and Opaque Liquids - Determination of Kinematic Viscosity and Calculation of Dynamic ViscosityIP 135 Determination of Rust-Prev

40、enting Characteristics of Steam Turbine Oil In the Presence of WaterIP 139 Petroleum Products and Lubricants - Determination of Acid or Base Number - Colour-Indicator Titration MethodIP 146 Determination of Foaming Characteristics of Lubricating Oils IP 154 Petroleum Products - Corrosiveness to Copp

41、er - Copper Strip Test IP 160 Determination of Density - Hydrometer Method IP 177 Test Method for Acid Number by Potentiometric Titration IP 226 Petroleum Products - Calculation of Viscosity Index from Kinematic ViscosityIP 278 Determination of Seal Compatibility Index of Petroleum Oils SAE MS1006 R

42、evised DEC2011 Page 7 of 11 2.1.8 ISO Publications Available from ANSI, 25 West 43rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org.ISO 868 Plastics and eboniteDetermination of indentation hardness by means of a durometer (Shore Hardness) ISO 1817 Rubber vulcanizedDetermination of

43、the effect of liquids ISO 2160 Petroleum productsCorrosiveness to copperCopper strip test ISO 2592 Petroleum products; Determination of flash and fire points; Cleveland open cup method ISO 3016 Petroleum products; Determination of pour point ISO 3104 Petroleum productsTransparent and opaque liquidsD

44、etermination of kinematic viscosity and calculation of dynamic viscosity ISO 3448 Industrial liquid lubricantsISO viscosity classification ISO 3675 Crude petroleum and liquid petroleum productsLaboratory determination of density or relative densityHydrometer methodISO 4263 Petroleum productsInhibite

45、d mineral oilsDetermination of oxidation characteristics ISO 4406 Hydraulic fluid powerFluidsMethod for coding level of contamination by solid particles ISO 6072 Hydraulic fluid powerCompatibility between elastomeric materials and fluids ISO 6247 Petroleum productsLubricating oilsDetermination of fo

46、aming characteristics ISO 6614 Petroleum productsDetermination of water separability of petroleum oils and synthetic fluidsISO 6618 Petroleum products and lubricantsDetermination of acid or base numberColour-indicator titration methodISO 6743/0 Lubricants, industrial oils and related products (Class

47、 L); Classification; GeneralISO 7120 Petroleum products and lubricantsPetroleum oils and other fluidsDetermination of rustPreventing characteristics in the presence of water ISO 7619 RubberDetermination of indentation hardness by means of pocket hardness meters 3. CONCEPT This specification defines

48、characteristics and requirements for type FD lubricants formulated with rust and oxidation inhibitors and anti-wear additives.Properties for Type FC (clutch fluids) are not addressed in this document.4. REQUIREMENTS AND TESTING See Table 2. Type F lubricants shall be compatible with all materials no

49、rmally encountered, including elastomer seals, coatings, metallic and non-metallic components, etc. SAE MS1006 Revised DEC2011 Page 8 of 11 TABLE 2 - TYPE FD (SPINDLE LUBRICANTS) PropertyType of Fluid RequirementsFDSpindle Oils Testing as specified in ISOTechnicalEquivalent StandardsDINTechnicalEquivalent StandardsASTMTechnicalEquivalent StandardsCETOPIP/BSISO Viscosi