SANS 10183-3-1-2009 Adhesives for wood Part 3-1 Non-structural applications - Classification of thermoplastic wood adhesives for non-structural applications《木材胶粘剂 第3-1部分：非结构应用 非结构热.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23455-3 SANS 10183-3-1:2009Edition 1 EN 204:2001Edition 2SOUTH AFRICAN NATIONAL STANDARD Adhesives for wood Part 3-1:Non-structural applic

4、ations Classification of thermoplastic wood adhesives for non-structural applications This national standard is the identical implementation of EN 204:2001 and is adopted with the permission of CEN, rue de Stassart 36, B-1050 Brussels. Published by SABS Standards Division 1 Dr Lategan Road Groenkloo

5、f Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 10183-3-1:2009 Edition 1 EN 204:2001 Edition 2 Table of changes Change No. Date Scope Acknowledgement The SABS Standards Division wishes to acknowledge the valuable assistance derived from publications

6、 of the European Committee for Standardization (CEN). National foreword This South African standard was approved by National Committee SABS SC 1010A, Adhesives for wood Adhesives for wood, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreeme

7、nt. This SANS document was published in November 2009. This SANS document supersedes SANS 10183:2000 (edition 1.1), in part. SANS 10183 consists of the following parts, under the general title Adhesives for wood: Part 1: Terminology and classification. Part 2: Structural applications. Part 3: Non-st

8、ructural applications. Part 4: Test methods. SANS 10183-3, in turn consists of the following sections: Section 1: Classification of thermoplastic wood adhesives for non-structural applications. Section 2: Determination of tensile shear strength of lap joints. Section 3: Classification of thermosetti

9、ng wood adhesives for non-structural applications. EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 204May 2001ICS 83.180 Supersedes EN 204:1991English versionClassification of thermoplastic wood adhesives for non-structuralapplicationsClassification des colles pour bois thermoplastiques usages non

10、 structurauxKlassifizierung von thermoplastischen Holzklebstoffen frnichttragende AnwendungenThis European Standard was approved by CEN on 19 April 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the statu

11、s of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A versio

12、n in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Ger

13、many, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2001 CEN All rights

14、of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 204:2001 ESANS 10183-3-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .Page 2EN 204:2001Contents PageForeword3Introduction .41 Scope 52

15、Normative references53 Terms and definitions .54 Classification .55 Test method .66 Requirements.6Bibliography 8SANS 10183-3-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .Page 3EN 204:2001ForewordThis European Standard has been prepar

16、ed by Technical Committee CEN/TC 193 “Adhesives“, the secretariat ofwhich is held by AENOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by November 2001, and conflicting national standards shall be

17、 withdrawn at the latestby November 2001.This European Standard supersedes EN 204:1991.This standard includes a Bibliography.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgi

18、um, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,Switzerland and the United Kingdom.SANS 10183-3-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SA

19、BS .Page 4EN 204:2001IntroductionEuropean Standards giving a common classification with respect to durability classes for wood adhesives will allowconsiderable improvement in consumer protection in any future product liability system with regard to propertiesguaranteed by the adhesive manufacturer.S

20、ANS 10183-3-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .Page 5EN 204:20011 ScopeThis European Standard classifies thermoplastic resin based wood adhesives for non-structural applications intodurability classes D1 to D4 based on the

21、dry and wet strengths of bond-lines measured under specified conditionsafter various conditioning treatments.For special applications, further tests that do not fall within the scope of this standard may be applicable.The adhesives described in this standard are suitable for the bonding of furniture

22、 and interior structures, panelling,doors, windows, stairs etc made of wood or derived timber products.This standard does not define the temperature resistance of bond-linesNOTE Thermoplastic resin are described in EN 923 as: polymer or copolymer, capable of being softened by heating andhardened by

23、cooling.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or r

24、evisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 205 Test methods for wood adhesives for non-structural applications De

25、termination of tensile shear strength of lap jointsEN 923 Adhesives Terms and definitions3 Terms and definitionsFor the purposes of this European standard the terms and definitions given in EN 923 and the following definitionapply.3.1thermoplastic wood adhesiveadhesive whose main constituent is a th

26、ermoplastic resin and which has been formulated for bonding wood4 ClassificationAn adhesive shall be classified in accordance with Table 1, which gives examples of climatic conditions and fieldsof application in which the bonded member is to be used. The classification shall be based on tests on thi

27、n bond-lines except when gap-filling properties are claimed, in which case it shall be based on tests using both thin andthick bond-lines as defined in EN 205.SANS 10183-3-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .Page 6EN 204:200

28、1Table 1 Description of durability classesDurabilityclassesExamples of climatic conditions and fields of applicationD1 Interior, in which the moisture content of the wood does not exceed 15 %.D2 Interior with occasional short-term exposure to running or condensed water and/orto occasional high humid

29、ity provided the moisture content of the wood does notexceed 18 %.D3 Interior with frequent short-term exposure to running or condensed water and/or toheavy exposure to high humidity. Exterior not exposed to weather.D4 Interior with frequent long-term exposure to running or condensed water. Exterior

30、exposed to weather but with protection by an adequate surface coating.5 Test methodThe adhesive shall be tested in accordance with EN 205 and as follows:a) either thin, or both thin and thick bond-lines shall be tested as appropriate (see clause 4);b) the tests shall be performed using the appropria

31、te conditioning sequence given in Table 2;c) the individual values and the mean value for 10 valid test pieces for each conditioning sequence shall berecorded.The standard atmosphere used as a control climate is either (20 2) C and (65 5)% relative humidity, (20/65), or(23 2) C and (50 5)% relative

32、humidity, (23/50).6 RequirementsWhen tested in accordance with EN 205 the mean strength of an adhesive shall:a) for thin bond-lines conform to the values shown in Table 2;b) for thick bond-lines, when required, be not lower than 80 % of the values shown in Table 2.NOTE The values given in Table 2 ar

33、e comparative values and should not be used as a basis for calculation, e.g. of designdata. They are not comparable with values obtained using test pieces of other dimensions.SANS 10183-3-1:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .

34、Page 7EN 204:2001Table 2 Minimum values of adhesive strength for thin bond-linesConditioning sequences Adhesive strength in N/mm2Durability classesSerial number Duration and condition D13)D23)D33)D43)17 dys1)in standardatmosphere2)10 10 10 102 7 days in standard atmosphere3 h in water at (20 5) C7 d

35、ays in standard atmosphere- 8 -3 7 days in standard atmosphere4 days in water at (20 5) C- 2 44 7 days in standard atmosphere4 days in water at (20 5) C7 days in standard atmosphere- 8 -5 7 days in standard atmosphere6 h in boiling water2 h in water at (20 5) C- 4NOTE 1 A longer conditioning time be

36、tween gluing and testing might be necessary as advised by theglue manufacturer.NOTE 2 The number used in the designation does not indicate ranking order. A given adhesive canbe assigned to more than one durability class.1)1 day = 24 hours2)(20 2) C and (65 5)% relative humidity or (23 2) C and (50 5

37、)% relative humidity- = No test required3) All minimum values indicated in the columns of durability classes D1 to D4 shall be reached as meanvalues for the classification of an adhesive (for example for D4, the conditioning sequences are 1, 3and 5).SANS 10183-3-1:2009This s tandard may only be used

38、 and printed by approved subscription and freemailing clients of the SABS .Page 8EN 204:2001BibliographyEN 12765 Classification of thermosetting wood adhesives for non-structuralapplicationsSANS 10183-3-1:2009This s tandard may only be used and printed by approved subscription and freemailing client

39、s of the SABS .SABS Standards Division The objective of the SABS Standards Division is to develop, promote and maintain South African National Standards. This objective is incorporated in the Standards Act, 2008 (Act No. 8 of 2008). Amendments and Revisions South African National Standards are updat

40、ed by amendment or revision. Users of South African National Standards should ensure that they possess the latest amendments or editions. The SABS continuously strives to improve the quality of its products and services and would therefore be grateful if anyone finding an inaccuracy or ambiguity whi

41、le using this standard would inform the secretary of the technical committee responsible, the identity of which can be found in the foreword. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 The SABS offers an individual notification service, which ensures that subscribers automatically receive not

42、ification regarding amendments and revisions to South African National Standards. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za Buying Standards Contact the Sales Office for South African and international standards, which are available in both electronic and hardcopy for

43、mat. Tel: +27 (0) 12 428 6883 Fax: +27 (0) 12 428 6928 E-mail: salessabs.co.za South African National Standards are also available online from the SABS website http:/www.sabs.co.za Information on Standards The Standards Information Centre provides a wide range of standards-related information on bot

44、h national and international standards, and is the official WTO/TBT enquiry point for South Africa. The Centre also offers an individual updating service called INFOPLUS, which ensures that subscribers automatically receive notification regarding amendments to, and revisions of, international standa

45、rds. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za Copyright The copyright in a South African National Standard or any other publication published by the SABS Standards Division vests in the SABS. Unless exemption has been granted, no extract may be reproduced, stored in a

46、 retrieval system or transmitted in any form or by any means without prior written permission from the SABS Standards Division. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any purpose other than implementation, prior written permission must be obtained. Details and advice can be obtained from the Senior Manager. Tel: +27 (0) 12 428 6666 Fax: +27 (0) 12 428 6928 E-mail: infosabs.co.za