SANS 15875-1-2004 Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) Part 1 General《冷热水装置塑料管道系统 交联聚乙烯(PE-X) 第1部分 一般》.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 23.040.01; 83.140.30; 91.140.60 ISBN 0-626-15796-X SANS 15875-1:2004 Edition 2 ISO 15875-1:2003 Edition 1 SOUTH AFRICAN NATIONAL STANDARD Plastics pi

4、ping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 1: General This national standard is the identical implementation of ISO 15875-1:2003 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1

5、 dr lategan road groenkloof ! private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code +27 12 www.stansa.co.za Standards South Africa SANS 15875-1:2004 Edition 2 ISO 15875-1:2003 Edition 1 Table of changes Change No. Date Scope Abstract Specifies the general aspects of c

6、rosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures according to the cla

7、ss of application. Covers a range of service conditions (application classes) and design pressure classes. Keywords buildings, cross-linked materials, definitions, installation, pipe couplings, pipelines, pipes, pipework systems, plastics, polyethylene, potable water, specifications, testing, tolera

8、nces (measurement), water, welded joints. National foreword This South African standard was approved by National Committee StanSA SC 5140.14A, Plastics pipes and fittings Polyethylene, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This

9、SANS edition cancels and replaces the first SANS edition (SANS 15875-1:2003). Reference numberISO 15875-1:2003(E)ISO 2003INTERNATIONAL STANDARD ISO15875-1First edition2003-12-01Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 1: General Systmes de can

10、alisations en plastique pour les installations deau chaude et froide Polythylne rticul (PE-X) Partie 1: Gnralits ISO 15875-1:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unl

11、ess the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademar

12、k of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. I

13、n the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, in

14、cluding photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publ

15、ished in Switzerland ii ISO 2003 All rights reservedISO 15875-1:2003(E) ISO 2003 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is norma

16、lly carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in th

17、e work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare

18、International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some

19、of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15875-1 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 138, Plastics pipes, fi

20、ttings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Throughout the text of this document, read “.this European Standard.” to mean “.this Int

21、ernational Standard.”. ISO 15875 consists of the following parts, under the general title Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X): Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the as

22、sessment of conformity Technical Specification ISO 15875-1:2003(E) iv ISO 2003 All rights reservedContentsForewordvIntroductionvi1Scope12Normative references13Terms and definitions, symbols and abbreviated terms.13.1Terms and definitions.13.1.1Geometrical terms and definitions13.1.2Terms and definit

23、ions related to service conditions.33.1.3Terms and definitions related to material characteristics.43.2Symbols43.3Abbreviated terms54Classification of service conditions55Material.65.1General.65.2Influence on water intended for human consumption65.3Reprocessable material.7Bibliography8ISO 15875-1:20

24、03(E) ISO 2003 All rights reserved vForewordThis document (EN ISO 15875-1:2003) has been prepared by Technical Committee CEN/TC 155 “Plastics pipingsystems and ducting systems”, the secretariat of which is held by NEN, in collaboration with Technical CommitteeISO/TC 138 “Plastics pipes, fittings and

25、 valves for the transport of fluids“.NOTE This standard was submitted for CEN enquiry as prEN 12318-1:1996.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2004, and conflicting national standa

26、rds shall be withdrawn at the latest byDecember 2005.This standard is part of a System Standard for plastics piping systems of a particular material for a specifiedapplication. There are a number of such System Standards.System Standards are based on the results of the work undertaken in ISO/TC 138

27、“Plastics pipes, fittings andvalves for the transport of fluids“, which is a Technical Committee of the International Organization forStandardization (ISO).They are supported by separate standards on test methods to which references are made throughout the SystemStandard.The System Standards are con

28、sistent with general standards on functional requirements and recommendedpractices for installation.EN ISO 15875:2003 consists of the following Parts1), under the general title Plastics piping systems for hot andcold water installations Crosslinked polyethylene (PE-X) Part 1: General (the present st

29、andard) Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the assessment of conformity (CEN ISO/TS 15875-7).This Part of EN ISO 15875 includes a Bibliography.At the date of publication of this standard, System Standards for piping systems of other plastics

30、 materials used forthe same application are the following:EN ISO 15874, Plastics piping systems for hot and cold water installations Polypropylene (PP)(ISO 15874:2003)EN ISO 15876, Plastics piping systems for hot and cold water installations Polybutylene (PB) (ISO 15876:2003)EN ISO 15877, Plastics p

31、iping systems for hot and cold water installations Chlorinated poly(vinyl chloride)(PVC-C) (ISO 15877:2003)For pipes and fittings which have conformed to the relevant national standard before 1stNovember 2003, as shownby the manufacturer or by a certification body, the national standard may continue

32、 to apply until 30thNovember2005According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Ital

33、y, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.1) This System Standard does not incorporate a Part 4 Ancillary equipment or a Part 6 Guidance for installation. For ancillaryequipment separate standards can apply. Guidance on installati

34、on of plastics piping systems made from different materialsintended to be used for hot and cold water installations is given by ENV 12108:20011.ISO 15875-1:2003(E) vi ISO 2003 All rights reservedIntroductionThe System Standard, of which this is Part 1, specifies the requirements for a piping system

35、when made fromcrosslinked polyethylene (PE-X). The piping system is intended to be used for hot and cold water installations.In respect of potential adverse effects on the quality of water intended for human consumption, caused by theproduct covered by EN ISO 15875: This standard provides no informa

36、tion as to whether the product may be used without restriction in any of theMember States of the EU or EFTA; It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulationsconcerning the use and/or the characteristics of this product remain in forc

37、e.Requirements and test methods for components of the piping system are specified in Part 2 and Part 3 ofEN ISO 15875:2003. Characteristics for fitness of purpose (mainly for joints) are covered in Part 5. Part 7(CEN ISO/TS 15875-7) gives guidance for the assessment of conformity.This Part of EN ISO

38、 15875 specifies the general aspects of the plastics piping system.ISO 15875-1:2003(E) ISO 2003 All rights reserved 11 ScopeThis Part of EN ISO 15875 specifies the general aspects of crosslinked polyethylene (PE-X) piping systemsintended to be used for hot and cold water installations within buildin

39、gs for the conveyance of water, whether or notintended for human consumption (domestic systems), and for heating systems, under design pressures andtemperatures according to the class of application (see Table 1).This standard covers a range of service conditions (application classes) and design pre

40、ssure and pipe dimensionclasses. For values of TD, Tmaxand Tmalin excess of those in Table 1, this standard does not apply.NOTE It is in the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account theirparticular requirements and any re

41、levant national regulations and installation practices or codes.It also specifies the test parameters for the test methods referred to in this standard.In conjunction with the other Parts of EN ISO 15875 (see Foreword) it is applicable to PE-X pipes, fittings, theirjoints and to joints with componen

42、ts of other plastics and non-plastics materials intended to be used for hot andcold water installations.2 Normative referencesThis Standard incorporates by dated or undated reference, provisions from other publications. These normativereferences are cited at the appropriate places in the text and th

43、e publications are listed hereafter. For datedreferences, subsequent amendments to or revisions of any of these publications apply to this Standard only whenincorporated in it by amendment or revision. For undated references the latest edition of the publication referred toapplies (including amendme

44、nts).EN ISO 15875-2:2003, Plastics piping systems for hot and cold water installations Crosslinked polyethylene(PE-X) Part 2: Pipes (ISO 15875-2:2003)EN ISO 15875-3:2003, Plastics piping systems for hot and cold water installations Crosslinked polyethylene(PE-X) Part 3: Fittings (ISO 15875-3:2003)IS

45、O 472:1999, Plastics VocabularyISO 1043-1:2001, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their specialcharacteristics3 Terms and definitions, symbols and abbreviated termsFor the purposes of this standard, the following terms and definitions, symbols and abbreviated terms ap

46、ply.3.1 Terms and definitionsIn addition to the terms and definitions given below, the terms and definitions given in ISO 472:1999 andISO 1043-1:2001 apply.3.1.1 Geometrical terms and definitions3.1.1.1 Nominal size3.1.1.1.1nominal size (DN)numerical designation of the size of a component, which is

47、a convenient round number, approximately equal to themanufacturing dimensions in millimetres (mm)3.1.1.1.2nominal size (DN/OD)nominal size, related to the outside diameterISO 15875-1:2003(E) 2 ISO 2003 All rights reserved3.1.1.2nominal outside diameter (dn)specified outside diameter, in millimetres,

48、 assigned to a nominal size DN/OD3.1.1.3outside diameter (at any point) (de)measured outside diameter through its cross section at any point of a pipe or spigot end of a fitting, rounded up tothe nearest 0,1 mm3.1.1.4mean outside diameter (dem)measured length of the outer circumference of a pipe or

49、spigot end of a fitting in any cross section divided by p( 3,142) rounded up to the nearest 0,1 mm3.1.1.5minimum mean outside diameter (dem,min)minimum value for the mean outside diameter as specified for a given nominal size3.1.1.6maximum mean outside diameter (dem,max)maximum value for the mean outside diameter as specified for a given nominal size3.1.1.7mean inside diameter of socket (dsm)arithmetical mean of two measured inside diameters perpendicular to each other at the midpoint of the socket