1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 23.040.01; 83.140.30; 91.140.60 ISBN 0-626-15798-6 SANS 15875-3:2004 Edition 2 ISO 15875-3:2003 Edition 1 SOUTH AFRICAN NATIONAL STANDARD Plastics pi
4、ping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 3: Fittings This national standard is the identical implementation of ISO 15875-3:2003 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa
5、1 dr lategan road groenkloof ! private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code +27 12 www.stansa.co.za Standards South Africa SANS 15875-3:2004 Edition 2 ISO 15875-3:2003 Edition 1 Table of changes Change No. Date Scope Abstract Specifies the characteristics of
6、fittings for crosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures approp
7、riate to the class of application. Covers a range of service conditions (application classes) and design pressure classes. Keywords buildings, definitions, fittings (pipes), installation, pipes, pipework systems, plastics, polyethylene, specifications, testing, tolerances (measurement), water. Natio
8、nal foreword This South African standard was approved by National Committee StanSA SC 5140.14A, Plastics pipes and fittings Polyethylene, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This SANS edition cancels and replaces the first SAN
9、S edition (SANS 15875-3:2003). Reference numberISO 15875-3:2003(E)ISO 2003INTERNATIONAL STANDARD ISO15875-3First edition2003-12-01Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 3: Fittings Systmes de canalisations en plastique pour les installations
10、 deau chaude et froide Polythylne rticul (PE-X) Partie 3: Raccords ISO 15875-3:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licen
11、sed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of th
12、e software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating t
13、o it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without pe
14、rmission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights re
15、servedISO 15875-3:2003(E) ISO 2003 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committe
16、es. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Inte
17、rnational Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International S
18、tandards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the su
19、bject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15875-3 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids,
20、 Subcommittee SC 2, Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Throughout the text of this document, read “.this European Standard.” to mean “.this International Standard.”. ISO 15875 consists of t
21、he following parts, under the general title Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X): Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the assessment of conformity Technical Specification
22、 ISO 15875-3:2003(E) iv ISO 2003 All rights reservedContentsForewordvIntroduction.vii1Scope12Normative references13Terms and definitions, symbols and abbreviated terms.24Material characteristics34.1Plastics fitting material.34.1.1Fitting material identical to PE-X pipe material34.1.2PE-X fitting mat
23、erial not identical to PE-X pipe material44.1.3Plastics fitting material other than PE-X.44.2Metallic fitting material44.3Influence on water intended for human consumption45General characteristics.55.1Appearance55.2Opacity.56Geometrical characteristics.56.1General.56.1.1Nominal diameter(s).56.1.2Ang
24、les56.1.3Threads56.2Dimensions of sockets for electrofusion fittings.56.3Dimensions of metallic fittings67Mechanical characteristics of plastics fittings.77.1General.77.2Fittings made from PE-X material identical to the PE-X pipe material.77.3Fittings made from PE-X not identical to the PE-X pipe ma
25、terial87.4Fittings made from plastics other than PE-X88Physical and chemical characteristics of plastics fittings.89Sealing elements.910Performance requirements911Marking.911.1General requirements911.2Minimum required marking.9Bibliography11ISO 15875-3:2003(E) ISO 2003 All rights reserved vForewordT
26、his document (EN ISO 15875-3:2003) has been prepared by Technical Committee CEN/TC 155 “Plastics pipingsystems and ducting systems”, the secretariat of which is held by NEN, in collaboration with Technical CommitteeISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“.This Eur
27、opean Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn at the latest byDecember 2005.NOTE This draft was submitted for CEN enquiry as prEN 12318-3:
28、1996.This standard is part of a System Standard for plastics piping systems of a particular material for a specifiedapplication. There are a number of such System Standards.System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes, fittingsand valves for th
29、e transport of fluids“, which is a Technical Committee of the International Organisation forStandardization (ISO).They are supported by separate Standards on test methods to which references are made throughout the SystemStandard.The System Standards are consistent with general standards on function
30、al requirements and recommendedpractices for installation.EN ISO 15875 consists of the following Parts1), under the general title: Plastics piping systems for hot and coldwater installations Crosslinked polyethylene (PE-X) Part 1: General Part 2: Pipes Part 3: Fittings (the present standard) Part 5:
31、 Fitness for purpose of the system Part 7: Guidance for the assessment of conformity (published as CEN ISO/TS 15875-7).This Part of EN ISO 15875 includes a BibliographyAt the date of publication of this standard, System Standards for piping systems of other plastics materials used forthe same applic
32、ation include the following:EN ISO 15874, Plastics piping systems for hot and cold water installations Polypropylene (PP)(ISO 15874:2003)EN ISO 15876, Plastics piping systems for hot and cold water installations Polybutylene (PB) (ISO 15876:2003)EN ISO 15877, Plastics piping systems for hot and cold
33、 water installations Chlorinated poly(vinyl chloride)(PVC-C) (ISO 15877:2003)For pipes and fittings which have conformed to the relevant national standard before 1stNovember 2003, as shownby the manufacturer or by a certification body, the national standard may continue to apply until 30thNovember20
34、05.1)This System Standard does not incorporate a Part 4 Ancillary equipment or a Part 6 Guidance for installation. For ancillaryequipment separate standards can apply. Guidance on installation of plastics piping systems made from different materialsintended to be used for hot and cold water installa
35、tions is given by ENV 121081.ISO 15875-3:2003(E) vi ISO 2003 All rights reservedAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France,
36、Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.ISO 15875-3:2003(E) ISO 2003 All rights reserved viiIntroductionThe System Standard of which this is Part 3, specifies the requirements for
37、a piping system when made frompolypropylene (PE-X). The piping system is intended to be used for hot and cold water installations.In respect of potential adverse effects on the quality of water intended for human consumption, caused by theproduct covered by this standard: This standard provides no i
38、nformation as to whether the product may be used without restriction in any of theMember States of the EU or EFTA; It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulationsconcerning the use and/or the characteristics of this product remain i
39、n force.Requirements and test methods for materials and components, other than fittings, are specified in Part 1 and Part 2of EN ISO 15875:2003. Characteristics for fitness for purpose (mainly for joints) are covered in Part 5. Part 7 (CENISO/TS 15875-7) gives guidance for the assessment of conformi
40、ty.This Part of EN ISO 15875 specifies the characteristics of the fittings.ISO 15875-3:2003(E) ISO 2003 All rights reserved 11 ScopeThis Part of EN ISO 15875 specifies the characteristics of fittings for crosslinked polyethylene (PE-X) pipingsystems intended to be used for hot and cold water install
41、ations within buildings for the conveyance of water,whether or not intended for human consumption, (domestic systems) and for heating systems, under designpressures and temperatures appropriate to the class of application (see Table 1 of EN ISO 15875-1:2003).This standard covers a range of service c
42、onditions (application classes) and design pressure classes. For values ofTD, Tmaxand Tmalin excess of those in Table 1 of Part 1, this standard does not apply.NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their
43、particular requirements and any relevant national regulations and installation practices or codes.It also specifies the test parameters for the test methods referred to in this standard.In conjunction with the other Parts of EN ISO 15875:2003 (see Foreword) it is applicable to fittings made fromcros
44、slinked polyethylene (PE-X) and to fittings made from other materials which are intended to be fitted to pipesconforming to EN ISO 15875-2:2003 for hot and cold water installations and whereby the joints conform to therequirements of EN ISO 15875-5.This standard is applicable to fittings of the foll
45、owing types: mechanical fittings; electrofusion fittings; fittings with incorporated inserts.2 Normative referencesThis Standard incorporates by dated or undated reference, provisions from other publications. These normativereferences are cited at the appropriate places in the text and the publicati
46、ons are listed hereafter. For datedreferences, subsequent amendments to or revisions of any of these publications apply to this Standard only whenincorporated in it by amendment or revision. For undated references the latest edition of the publication referred toapplies (including amendments).EN 578
47、, Plastics piping systems Plastics pipes and fittings Determination of the opacityISO 15875-3:2003(E) 2 ISO 2003 All rights reservedEN 579, Plastics piping systems Crosslinked polyethylene (PE-X) pipes Determination of degree ofcrosslinking by solvent extractionEN 681-1, Elastomeric seals Materials
48、requirements for pipe joint seals used in water and drainage applicationsPart 1: Vulcanized rubberEN 681-2, Elastomeric seals Material requirements for pipe joint seals used in water and drainage applicationsPart 2: Thermoplastic elastomersEN 921:1994, Plastics piping systems Thermoplastics pipes De
49、termination of resistance to internal pressureat constant temperatureEN 1254-3, Copper and copper alloys Plumbing fittings Part 3: Fittings with compression ends for use withplastics pipesEN 10088-1, Stainless steels Part 1: List of stainless steelsprEN 10226-1, Pipe threads where pressure-tight joints are made on the threads Part 1: Taper external threadsand parallel internal threads Dimensions, tolerances and designationEN 12107, Plastics piping systems Injection-moulded thermoplastics
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1