SANS 15875-5-2004 Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) Part 5 Fitness for purpose of the system《冷热水装置用塑料管道系统 交联聚乙烯(PE-X) 第.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 23.040.01; 83.140.30; 91.140.60 ISBN 0-626-15799-4 SANS 15875-5:2004 Edition 2 ISO 15875-5:2003 Edition 1 SOUTH AFRICAN NATIONAL STANDARD Plastics pi

4、ping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 5: Fitness for purpose of the system This national standard is the identical implementation of ISO 15875-5:2003 and is adopted with the permission of the International Organization for Standardization. Published b

5、y Standards South Africa 1 dr lategan road groenkloof ! private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code +27 12 www.stansa.co.za Standards South Africa SANS 15875-5:2004 Edition 2 ISO 15875-5:2003 Edition 1 Table of changes Change No. Date Scope Abstract Specifie

6、s the characteristics of the fitness for purpose of crosslinked polyethylene (PE-X) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under de

7、sign pressures and temperatures according to the class of application. Covers a range of service conditions (application classes) and design pressure classes. Keywords buildings, cross-linked materials, definitions, installation, pipe couplings, pipe fittings, pipelines, pipework systems, plastics,

8、polyethylene, specifications, testing, tolerances (measurement), water, welded joints. National foreword This South African standard was approved by National Committee StanSA SC 5140.14A, Plastics pipes and fittings Polyethylene, in accordance with procedures of Standards South Africa, in compliance

9、 with annex 3 of the WTO/TBT agreement. This SANS edition cancels and replaces the first SANS edition (SANS 15875-5:2003). Reference numberISO 15875-5:2003(E)ISO 2003INTERNATIONAL STANDARD ISO15875-5First edition2003-12-01Plastics piping systems for hot and cold water installations Crosslinked polye

10、thylene (PE-X) Part 5: Fitness for purpose of the system Systmes de canalisations en plastique pour les installations deau chaude et froide Polythylne rticul (PE-X) Partie 5: Aptitude lemploi du systme ISO 15875-5:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance wit

11、h Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing p

12、olicy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Ever

13、y care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publicatio

14、n may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20

15、Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reservedISO 15875-5:2003(E) ISO 2003 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national sta

16、ndards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International or

17、ganizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules give

18、n in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 7

19、5 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15875-5 was prepared by the European Committee for Stand

20、ardization (CEN) in collaboration with Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).

21、 Throughout the text of this document, read “.this European Standard.” to mean “.this International Standard.”. ISO 15875 consists of the following parts, under the general title Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X): Part 1: General Part 2: Pip

22、es Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the assessment of conformity Technical Specification ISO 15875-5:2003(E) iv ISO 2003 All rights reservedContents1Scope12Normative references13Terms and definitions, symbols and abbreviated terms.24Fitness for purpose

23、of the joints and the piping system.24.1General24.2Internal pressure test34.3Bending test.34.4Pull-out test44.5Thermal cycling test54.6Pressure cycling test.54.7Leaktightness under vacuum.6Bibliography7ForewordvIntroduction.viiISO 15875-5:2003(E) ISO 2003 All rights reserved vForewordThis document (

24、EN ISO 15875-5:2003) has been prepared by Technical Committee CEN/TC 155 “Plastics pipingsystems and ducting systems”, the secretariat of which is held by NEN, in collaboration with Technical CommitteeISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“.This European Standard

25、. shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn at the latest byDecember 2005.NOTE 1 This draft was submitted for CEN enquiry as prEN 12318-5:1996.This s

26、tandard is part of a System Standard for plastics piping systems of a particular material for a specifiedapplication. There are a number of such System Standards.System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings andvalves for the transport of fl

27、uids”, which is a Technical Committee of the International Organization forStandardization (ISO).They are supported by separate standards on test methods to which references are made throughout the SystemStandard.The System Standards are consistent with general standards on functional requirements a

28、nd recommendedpractices for installation.EN ISO 15875 consists of the following Parts 1), under the general title Plastics piping systems for hot and coldwater installations Crosslinked Polyethylene (PE-X) Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system (the

29、present standard) Part 7: Guidance for the assessment of conformity (intended to be published as CEN ISO/TS 15875-7).This Part of EN ISO 15874:2003 includes a Bibliography.At the date of publication of this standard, System Standards for piping systems of other plastics materials used forthe same ap

30、plication are the following:EN ISO 15874, Plastics piping systems for hot and cold water installations Polypropylene (PP)(ISO 15875:2003)EN ISO 15876, Plastics piping systems for hot and cold water installations Polybutylene (PB) (ISO 15876:2003)EN ISO 15877, Plastics piping systems for hot and cold

31、 water installations Chlorinated poly(vinyl chloride)(PVC-C) (ISO 15877:2003)For pipes and fittings which have conformed to the relevant national standard before 1stNovember, 2003, asshown by the manufacturer or by a certification body, the national standard may continue to apply until 30thNovember,

32、 2005.1) This System Standard does not incorporate a Part 4 Ancillary equipment or a Part 6: Guidance for installation. For ancillaryequipment separate standards can apply. Guidance on installation of plastics piping systems made from different materialsintended to be used for hot and cold water ins

33、tallations is given by ENV 121081.ISO 15875-5:2003(E) vi ISO 2003 All rights reservedAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,Fra

34、nce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.ISO 15875-5:2003(E) ISO 2003 All rights reserved viiIntroductionThe System Standard, of which this is Part 5, specifies the requirement

35、s for a piping system and its componentswhen made from crosslinked polyethylene (PE-X). The piping system is intended to be used for hot and cold waterinstallations.In respect of potential adverse effects on the quality of water intended for human consumption, caused by theproduct covered by EN ISO

36、15875; This standard provides no information as to whether the product may be used without restriction in any of theMember States of the EU or EFTA; It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulationsconcerning the use and/or the charac

37、teristics of this product remain in force.Requirements and test methods for components of the piping system are specified in Part 1, 2 and 3 of this SystemStandard. Part 7 (CEN ISO/TS 15875-7) gives guidance for the assessment of conformity.This Part of EN ISO 15875 specifies the characteristics of

38、fitness for purpose of the piping systems.ISO 15875-5:2003(E) ISO 2003 All rights reserved 11 ScopeThis Part of EN ISO 15875 specifies the characteristics of the fitness for purpose of crosslinked polyethylene(PE-X) piping systems, intended to be used for hot and cold water installations within buil

39、dings for the conveyanceof water whether or not intended for human consumption (domestic systems) and for heating systems, underdesign pressures and temperatures according to the class of application (see Table 1 of EN ISO 15875-1:2003).This standard covers a range of service conditions (application

40、 classes) and design pressure classes. . For valuesof TD, Tmaxand Tmalin excess of those in Table 1 of Part 1, this standard does not apply.NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account theirparticular requireme

41、nts and any relevant national regulations and installation practices or codes.It also specifies the test parameters for the test methods referred to in this standard.In conjunction with the other parts of EN ISO 15875:2003 (see Foreword) it is applicable to PE-X pipes, fittings,their joints and to j

42、oints with components of other plastics and non-plastics materials intended to be used for hotand cold water installations.2 Normative referencesThis standard incorporates by dated or undated reference, provisions from other publications. These normativereferences are cited at the appropriate places

43、 in the text and the publications are listed hereafter. For datedreferences, subsequent amendments to, or revisions of, any of these publications apply to this standard only whenincorporated in it by amendment or revision. For undated references the latest edition of the publication referred toappli

44、es (including amendments).EN 712, Thermoplastics piping systems End-load bearing mechanical joints between pressure pipes and fittingsTest method for resistance to pull-out under constant longitudinal forceEN 713, Plastics piping systems Mechanical joints between fittings and polyolefin pressure pip

45、es Testmethod for leaktightness under internal pressure of assemblies subjected to bendingISO 15875-5:2003(E) 2 ISO 2003 All rights reservedEN 921, Plastics piping systems Thermoplastics pipes Determination of resistance to internal pressure atconstant temperatureEN 12293, Plastics piping systems Th

46、ermoplastics pipes and fittings for hot and cold water Test method forthe resistance of mounted assemblies to temperature cyclingEN 12294, Plastics piping systems Systems for hot and cold water Test method for leaktightness undervacuumEN 12295, Plastics piping systems Thermoplastics pipes and associ

47、ated fittings for hot and cold water Testmethod for resistance of joints to pressure cyclingEN ISO 15875-1:2003, Plastics piping system for hot and cold water installations Crosslinked polyethylene(PE-X) Part 1: General (ISO 15875-1:2003)EN ISO 15875-2:2003, Plastics piping system for hot and cold w

48、ater installations Crosslinked polyethylene(PE-X) Part 2: Pipes (ISO 15875-2:2003)3 Terms and definitions, symbols and abbreviated termsFor the purpose of this standard, the terms and definitions, symbols and abbreviated terms given inEN ISO 15875-1:2003 apply.4 Fitness for purpose of the joints and

49、 the piping system4.1 GeneralWhen tested in accordance with the applicable test methods as specified in Table 1, using the indicatedparameters given in 4.2 to 4.7, as applicable, the joints and the piping system shall have characteristics conformingto the requirements given in the applicable clauses.For the tests described the fittings shall be connected to the pipe with which they are intended to be used.Table 1 specifies the tests applicable for each different type of jointing sy