SANS 15876-1-2005 Plastics piping systems for hot and cold water installations - Polybutylene (PB) Part 1 General《冷热水装置用塑料管道系统 聚丁烯(PB) 第1部分 总则》.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 83.140.30; 91.140.60 ISBN 0-626-16961-5 SANS 15876-1:2005Edition 1ISO 15876-1:2003Edition 1SOUTH AFRICAN NATIONAL STANDARD Plastics piping systems fo

4、r hot and cold water installations Polybutylene (PB) Part 1: General This national standard is the identical implementation of ISO 15876-1:2003 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road groenkloof p

5、rivate bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 15876-1:2005 Edition 1 ISO 15876-1:2003 Edition 1 Table of changes Change No. Date Scope Abstract Specifies the general aspects of polybutylene (PB) piping system

6、s intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application. Keywords buildings, classif

7、ication, cold water, drinking water supply, heaters, hot water, operating conditions, pipe couplings, pipe fittings, pipeline installations, pipelines, pipes, piping system, plastic pipelines, plastic pipes, plastics, plastic tubes, polyolefins, potable water, specifications, thermal environment sys

8、tems, tubes, warm water, water, water pipes, water practice, water supply, welded joints. National foreword This South African standard was approved by National Committee StanSA SC 5140.14C, Plastics pipes and fittings Polypropylene pipes, in accordance with procedures of Standards South Africa, in

9、compliance with annex 3 of the WTO/TBT agreement. Reference numberISO 15876-1:2003(E)ISO 2003INTERNATIONAL STANDARD ISO15876-1First edition2003-12-01Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 1: General Systmes de canalisations en plastique pour les installat

10、ions deau chaude et froide Polybutne (PB) Partie 1: Gnralits ISO 15876-1:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to

11、 and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the soft

12、ware products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it i

13、s found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permissi

14、on in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reserved

15、ISO 15876-1:2003(E) ISO 2003 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Ea

16、ch member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the Internatio

17、nal Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standar

18、ds adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject

19、of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15876-1 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subco

20、mmittee SC 2, Plastics pipes and fittings for water supplies, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Throughout the text of this document, read “.this European Standard.” to mean “.this International Standard.”. ISO 15876 consists of the fol

21、lowing parts, under the general title Plastics piping systems for hot and cold water installations Polybutylene (PB): Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the assessment of conformity Technical Specification ISO 15876-1:2003(E)

22、 iv ISO 2003 All rights reservedContentsIntroduction vi1Scope12Normative references13Terms and definitions, symbols and abbreviated terms.13.1Terms and definitions.13.1.1Geometrical terms and definitions13.1.2Terms and definitions related to service conditions.33.1.3Terms and definitions related to

23、material characteristics.43.2Symbols43.3Abbreviated terms54Classification of service conditions55Material.65.1General.65.2Influence on water intended for human consumption65.3Crystallisation.75.4Reprocessable material.7Bibliography8Foreword vISO 15876-1:2003(E) ISO 2003 All rights reserved vForeword

24、This document (EN ISO 15876-1:2003) has been prepared by Technical Committee CEN/TC 155 “Plastics pipingsystems and ducting systems”, the secretariat of which is held by NEN, in collaboration with Technical CommitteeISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“.NOTE Th

25、is standard was submitted for CEN enquiry as prEN 12319-1:1996.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn at the latest byDecem

26、ber 2005.This standard is Part of a System Standard for plastics piping systems of a particular material for a specifiedapplication. There are a number of such System Standards.System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings andvalves for the

27、transport of fluids“, which is a Technical Committee of the International Organisation forStandardization (ISO).They are supported by separate standards on test methods to which references are made throughout the SystemStandard.The System Standards are consistent with general standards on functional

28、 requirements and recommendedpractices for installation.EN ISO 15876 consists of the following Parts 1) under the general title: Plastics piping systems for hot and coldwater installations Polybutylene (PB)Part 1: General (the present standard)Part 2: PipesPart 3: FittingsPart 5: Fitness for purpose

29、 of the systemPart 7: Guidance for the assessment of conformity (CEN ISO/TS 15876-7).This Part 1 of EN ISO 15876 includes a Bibliography.At the date of publication of this standard, System Standards for piping systems of other plastics materials used forthe same application are the following:EN ISO

30、15874, Plastics piping systems for hot and cold water installations Polypropylene (PP)(ISO 15874:2003)EN ISO 15875, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X)(ISO 15875:2003)EN ISO 15877, Plastics piping systems for hot and cold water installations C

31、hlorinated poly(vinyl chloride) (PVC-C) (ISO 15877:2003)For pipes and fittings which have conformed to the relevant national standard before 1stNovember, 2003, asshown by the manufacturer or by a certification body, the national standard may continue to apply until 30thNovember, 2005.According to th

32、e CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Port

33、ugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.1) This System Standard does not incorporate a Part 4 Ancillary equipment or a Part 6 Guidance for installation. For ancillaryequipment separate standards can apply. A guidance for installation for plastics piping systems made from dif

34、ferent materials,intended to be used for hot and cold water installations, is covered by ENV 121081.ISO 15876-1:2003(E) vi ISO 2003 All rights reservedIntroductionThe System Standard, of which this is Part 1, specifies the requirements for a piping system when made frompolybutylene (PB). The piping

35、system is intended to be used for hot and cold water installations.In respect of potential adverse effects on the quality of water intended for human consumption, caused by theproduct covered by EN ISO 15876: This standard provides no information as to whether the product may be used without restric

36、tion in any of theMember States of the EU or EFTA; It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulationsconcerning the use and/or the characteristics of this product remain in force.Requirements and test methods for components of the pipi

37、ng systems, are specified in Part 2 and Part 3 ofEN ISO 15876:2003. Characteristics for fitness for purpose (mainly for joints) are covered in Part 5. Part 7(CEN ISO/TS 15876-7) gives guidance for the assessment of conformity.This Part of EN ISO 15876 specifies the general aspects of the plastics pi

38、ping system.ISO 15876-1:2003(E) ISO 2003 All rights reserved 11 ScopeThis Part of EN ISO 15876 specifies the general aspects of polybutylene (PB) piping systems intended to be usedfor hot and cold water installations within buildings for the conveyance of water whether or not intended for humanconsu

39、mption (domestic systems) and for heating systems, under design pressures and temperatures according tothe class of application (see Table 1).This standard covers a range of service conditions (application classes) and design pressure and pipe dimensionclasses. For values of TD, Tmaxand Tmalin exces

40、s of those in Table 1, this standard does not apply.NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account theirparticular requirements and any relevant national regulations and installation practices or codes.It also sp

41、ecifies the test parameters for the test methods referred to in this standard.In conjunction with the other Parts of EN ISO 15876 (see Foreword) it is applicable to PB pipes, fittings, their jointsand to joints with components of other plastics and non-plastics materials intended to be used for hot

42、and coldwater installations.2 Normative referencesThis Standard incorporates by dated or undated reference, provisions from other publications. These normativereferences are cited at the appropriate places in the text and the publications are listed hereafter. For datedreferences, subsequent amendme

43、nts to or revisions of any of these publications apply to this Standard only whenincorporated in it by amendment or revision. For undated references the latest edition of the publication referred toapplies (including amendments).EN ISO 15876-2:2003, Plastics piping system for hot and cold water inst

44、allations Polybutylene (PB) Part 2:Pipes (ISO 15876-2:2003)EN ISO 15876-3:2003, Plastics piping system for hot and cold water installations Polybutylene (PB) Part 3:Fittings (ISO 15876-3:2003)ISO 472:1999, Plastics VocabularyISO 1043-1:2001, Plastics Symbols and abbreviated terms Part 1: Basic polym

45、ers and their specialcharacteristics3 Terms and definitions, symbols and abbreviated termsFor the purposes of this standard, the following terms and definitions, symbols and abbreviated terms apply.3.1 Terms and definitionsIn addition to the terms and definitions given below, the terms and definitio

46、ns given in ISO 472:1999 andISO 1043-1:2001 apply.3.1.1 Geometrical terms and definitions3.1.1.1 Nominal size3.1.1.1.1nominal size (DN)numerical designation of the size of a component, which is a convenient round number, approximately equal to themanufacturing dimensions, in millimetres (mm)3.1.1.1.

47、2nominal size (DN/OD)nominal size, related to outside diameterISO 15876-1:2003(E) 2 ISO 2003 All rights reserved3.1.1.2nominal outside diameter (dn)specified diameter, in millimetres, assigned to a nominal size DN/OD3.1.1.3outside diameter (at any point) (de)measured outside diameter through the cro

48、ss section at any point of a pipe or spigot end of a fitting, rounded up tothe nearest 0,1 mm3.1.1.4mean outside diameter (dem)measured length of the outer circumference of a pipe or spigot end of a fitting in any cross section dividedby p ( 3,142) rounded up to the nearest 0,1 mm3.1.1.5minimum mean

49、 outside diameter (dem,min)minimum value of the mean outside diameter as specified for a given nominal size3.1.1.6maximum mean outside diameter (dem,max)maximum value of the mean outside diameter as specified for a given nominal size3.1.1.7mean inside diameter of socket (dsm)arithmetical mean of two measured inside diameters perpendicular to each other at the midpoint of the socketlength3.1.1.8out-of-roundness (ovality)difference between the measured maximum outside diameter and the measured minimum out