1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 83.140.30; 91.140.60 ISBN 0-626-16954-2 SANS 15876-5:2005Edition 1ISO 15876-5:2003Edition 1SOUTH AFRICAN NATIONAL STANDARD Plastics piping systems fo
4、r hot and cold water installations Polybutylene (PB) Part 5: Fitness for purpose of the system This national standard is the identical implementation of ISO 15876-5:2003 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr
5、 lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 15876-5:2005 Edition 1 ISO 15876-5:2003 Edition 1 Table of changes Change No. Date Scope Abstract Specifies the characteristics of the f
6、itness for purpose of polybutylene (PB) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures according
7、to the class of application. Keywords buildings, cold water, drinking water lines, drinking water supply, fitness for purpose, heated systems, heating installations, hot water, house installations, installations, joints, materials, operating requirements, pipe couplings, pipeline installations, pipe
8、lines, pipes, piping system, plastic pipelines, plastic pipes, plastics, plastic tubes, polybutylene, polyester resins, polyolefins, potable water, specifications, systems, thermal cycling, water, water pipelines, water pipes, water practice, water supply, welded joints. National foreword This South
9、 African standard was approved by National Committee StanSA SC 5140.14C, Plastics pipes and fittings Polypropylene pipes, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. Reference numberISO 15876-5:2003(E)ISO 2003INTERNATIONAL STANDARD IS
10、O15876-5First edition2003-12-01Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 5: Fitness for purpose of the system Systmes de canalisations en plastique pour les installations deau chaude et froide Polybutne (PB) Partie 5: Aptitude lemploi du systme ISO 15876-5:2
11、003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
12、 file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Inf
13、o relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
14、 ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in
15、the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reservedISO 15876-5:2003(E) ISO 2003 All rights reserved iiiForeword ISO (the Inte
16、rnational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has
17、 been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical s
18、tandardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies
19、 for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or
20、 all such patent rights. ISO 15876-5 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies, in accordanc
21、e with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Throughout the text of this document, read “.this European Standard.” to mean “.this International Standard.”. ISO 15876 consists of the following parts, under the general title Plastics piping systems for hot and
22、cold water installations Polybutylene (PB): Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the assessment of conformity Technical Specification ISO 15876-5:2003(E) iv ISO 2003 All rights reservedContentsForewordvIntroduction.vii1Scope12N
23、ormative references13Terms and definitions, symbols and abbreviated terms.14Fitness for purpose of the joints and the piping system24.1General.24.2Internal pressure test.24.3Bending test.34.4Pull-out test44.5Thermal cycling test.54.6Pressure cycling test54.7Leaktightness under vacuum.6Bibliography7I
24、SO 15876-5:2003(E) ISO 2003 All rights reserved vForewordThis document (EN ISO 15876-5:2003) has been prepared by Technical Committee CEN/TC 155 “Plastics pipingsystems and ducting systems”, the secretariat of which is held by NEN, in collaboration with Technical CommitteeISO/TC 138 “Plastics pipes,
25、 fittings and valves for the transport of fluids“.NOTE This draft was submitted for CEN enquiry as prEN 12319-6:1996.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2004, and conflicting natio
26、nal standards shall be withdrawn at the latest byDecember 2005.This standard is part of a System Standard for plastics piping systems of a particular material for a specifiedapplication. There are a number of such System Standards.System Standards are based on the results of the work undertaken in I
27、SO/TC 138 “Plastics pipes, fittings andvalves for the transport of fluids”, which is a Technical Committee of the International Organization forStandardization (ISO).They are supported by separate standards on test methods to which references are made throughout the SystemStandard.The System Standar
28、ds are consistent with general standards on functional requirements and recommendedpractices for installation.EN ISO 15876 consists of the following Parts 1), under the general title Plastics piping systems for hot and coldwater installations Polybutylene (PB) Part 1: General Part 2: Pipes Part 3: F
29、ittings Part 5: Fitness for purpose of the system (the present standard) Part 7: Guidance for the assessment of conformity (CEN ISO/TS 15876-7).This Part of EN ISO 15876 includes a Bibliography.At the date of publication of this standard, System Standards for piping systems of other plastics materia
30、ls used forthe same application are the following:EN ISO 15874, Plastics piping systems for hot and cold water installations Polypropylene (PP)(ISO 15874:2003)EN ISO 15875, Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X)(ISO 15875:2003)EN ISO 15877, Plast
31、ics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride)(PVC-C) (ISO 15877:2003)For pipes and fittings which have conformed to the relevant national standard before 1stNovember 2003, as shownby the manufacturer or by a certification body, the national standard may con
32、tinue to apply until 30thNovember2005.1) This System Standard does not incorporate a Part 4 Ancillary equipment or a Part 6: Guidance for installation. For ancillaryequipment separate standards can apply. Guidance on installation of plastics piping systems made from different materialsintended to be
33、 used for hot and cold water installations is given by ENV 121081.ISO 15876-5:2003(E) vi ISO 2003 All rights reservedAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czec
34、h Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.ISO 15876-5:2003(E) ISO 2003 All rights reserved viiIntroductionThe System Standard, of which this is P
35、art 5, specifies the requirements for a piping system and its componentswhen made from polybutylene (PB). The piping system is intended to be used for hot and cold water installations.In respect of potential adverse effects on the quality of water intended for human consumption, caused by theproduct
36、 covered by EN ISO 15876; This standard provides no information as to whether the product may be used without restriction in any of theMember States of the EU or EFTA; It should be noted that, while awaiting the adoption of verifiable European criteria, existing national regulationsconcerning the us
37、e and/or the characteristics of this product remain in force.Requirements and test methods for components of the piping system are specified in Part 1, 2 and 3 of this SystemStandard. Part 7 (CEN ISO/TS 15876-7) gives guidance for the assessment of conformity.This Part of EN ISO 15876 specifies the
38、characteristics of fitness for purpose of the piping systems.ISO 15876-5:2003(E) ISO 2003 All rights reserved 11 ScopeThis Part of EN ISO 15876 specifies the characteristics of the fitness for purpose of polybutylene (PB) pipingsystems, intended to be used for hot and cold water installations within
39、 buildings for the conveyance of water,whether or not intended for human consumption, (domestic systems) and for heating systems, under designpressures and temperatures according to the class of application (see Table 1 of EN ISO 15876-1:2003).This standard covers a range of service conditions (appl
40、ication classes) and design pressure classes For values ofT, Tmaxand Tmalin excess of those in Table 1 of Part 1, this standard does not apply.NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account theirparticular requir
41、ements and any relevant national regulations and installation practices or codes.It also specifies the test parameters for the test methods referred to in this standard.In conjunction with the other Parts of EN ISO 15876:2003 it is applicable to PB pipes, fittings, their joints and tojoints with com
42、ponents of other plastics and non-plastics materials intended to be used for hot and cold waterinstallations.2 Normative referencesThis Standard incorporates by dated or undated reference, provisions from other publications. These normativereferences are cited at the appropriate places in the text a
43、nd the publications are listed hereafter. For datedreferences, subsequent amendments to or revisions of any of these publications apply to this Standard only whenincorporated in it by amendment or revision. For undated references the latest edition of the publication referred toapplies (including am
44、endments).EN 712, Thermoplastics piping systems End-load bearing mechanical joints between pressure pipes and fittingsTest method for resistance to pull-out under constant longitudinal forceEN 713, Plastics piping systems Mechanical joints between fittings and polyolefin pressure pipes Testmethod fo
45、r leaktightness under internal pressure of assemblies subjected to bendingEN 921, Plastics piping systems Thermoplastics pipes Determination of resistance to internal pressure atconstant temperatureEN 12293, Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method
46、 forthe resistance of mounted assemblies to temperature cyclingEN 12294, Plastics piping systems Systems for hot and cold water Test method for leaktightness undervacuumEN 12295, Plastics piping systems Thermoplastics pipes and associated fittings for hot and cold water Testmethod for resistance of
47、joints to pressure cyclingEN ISO 15876-1:2003, Plastics piping system for hot and cold water installations Polybutylene (PB) Part 1:GeneralEN ISO 15876-2:2003, Plastics piping system for hot and cold water installations Polybutylene (PB) Part 2:Pipes3 Terms and definitions, symbols and abbreviated t
48、ermsFor the purposes of this standard the terms and definitions, symbols and abbreviated terms given inEN ISO 15876-1:2003 apply.ISO 15876-5:2003(E) 2 ISO 2003 All rights reserved4 Fitness for purpose of the joints and the piping system4.1 GeneralWhen tested in accordance with the applicable test me
49、thods as specified in Table 1, using the indicatedparameters given in 4.2 to 4.7, as applicable, the joints and the piping system shall have characteristics conformingto the requirements given in the applicable clauses.For the tests described the fittings shall be connected to the pipe with which they are intended to be used.Table 1 specifies the tests applicable for each different type of jointing system covered by this standard.Table 1 Joint testsTest Jointing system aTest parametersT
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1