1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21747-1 SANS 21138-1:2008Edition 1ISO 21138-1:2007Edition 1SOUTH AFRICAN NATIONAL STANDARD Plastics piping systems for non-pressure underg
4、round drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system This national standard is the identical implementation of ISO 211
5、38-1:2007 and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 21138-1:2008 Edition 1 ISO: 21138-1:2
6、007 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS SC 138H, Water and sanitation Equipment and systems Plastics pipes and fittings, in accordance with procedures of the SABS Standards Division, in compliance with
7、 annex 3 of the WTO/TBT agreement. This document was published in August 2008. Reference numberISO 21138-1:2007(E)ISO 2007INTERNATIONAL STANDARD ISO21138-1First edition2007-10-15Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized
8、 poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement sans pression enterrs Systmes de canalisation
9、s parois structures en poly(chlorure de vinyle) non plastifi (PVC-U), polypropylne (PP) et polythylne (PE) Partie 1: Spcifications des matires et critres de performance des tubes, raccords et systme SANS 21138-1:2008This s tandard may only be used and printed by approved subscription and freemailing
10、 clients of the SABS .ISO 21138-1:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performi
11、ng the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF f
12、ile can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secr
13、etariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writ
14、ing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reservedSANS 21138
15、-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 21138-1:2007(E) ISO 2007 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms, definitions, symbols and abbreviated terms. 3
16、3.1 Terms and definitions. 3 3.2 Symbols . 6 3.3 Abbreviated terms 7 4 Material 7 4.1 General. 7 4.2 Sealing ring retaining components. 7 4.3 Sealing rings . 7 4.4 Fused or welded joints. 7 5 Designation of wall construction 7 6 Colour 8 7 Geometrical characteristics. 8 8 Types of fitting 8 8.1 Gene
17、ral. 8 8.2 Design length of fittings. 11 9 Functional characteristics . 11 10 Relation between ring stiffness, installation technique and resulting deflection . 11 Annex A (informative) General material characteristics of PVC-U, PP and PE pipes and fittings. 13 Annex B (informative) General performa
18、nce characteristics of PVC-U, PP and PE pipes and fittings 14 Annex C (informative) Structural design 15 Bibliography . 18 SANS 21138-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 21138-1:2007(E) iv ISO 2007 All rights reservedFor
19、eword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a tech
20、nical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
21、 electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated t
22、o the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for
23、 identifying any or all such patent rights. ISO 21138-1 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land drainage). ISO 21138 consists of the fo
24、llowing parts, under the general title Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE): Part 1: Material specifications and performance criteria for pipes
25、, fittings and system Part 2: Pipes and fittings with smooth external surface, Type A Part 3: Pipes and fittings with non-smooth external surface, Type B SANS 21138-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 21138-1:2007(E) ISO
26、 2007 All rights reserved vIntroduction ISO 21138 is the system standard covering the plastics piping systems for non-pressure underground drainage and sewerage, in particular thermoplastics structured-wall piping systems. SANS 21138-1:2008This s tandard may only be used and printed by approved subs
27、cription and freemailing clients of the SABS .SANS 21138-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL STANDARD ISO 21138-1:2007(E) ISO 2007 All rights reserved 1Plastics piping systems for non-pressure underground drain
28、age and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system 1 Scope This part of ISO 21138 specifies the definitions and requirements fo
29、r pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems in the field of non-pressure underground systems for underground drainage and sewerage. NOTE 1 These pipes, fittings and the system can be use
30、d for highway drainage and surface water. This part of ISO 21138 specifically refers to PVC, PP and PE materials. NOTE 2 Other thermoplastic materials can be added via an addendum. This part of ISO 21138 covers a range of pipe and fitting sizes, materials, pipe constructions, nominal ring stiffnesse
31、s, and gives recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjun
32、ction with ISO 21138-2 and ISO 21138-3, it is applicable to PVC-U, PP and PE structured-wall pipes and fittings, to their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for the transport of drainage and sewerage. It is
33、applicable to PVC-U, PP and PE structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. NOTE 4 Pipes, fittings and other components conforming to any plastics product standards referred to in Clause 2 can be used with
34、 pipes and fittings conforming to this part of ISO 21138 when they conform to the requirements for joint dimensions given in Parts 2 and 3 of ISO 21138 and to the performance requirements given in Clause 9. NOTE 5 For dimensions larger than DN/OD 1200 or DN/ID 1200, this part of ISO 21138 can serve
35、as a general guide regarding appearance, colour, physical and mechanical characteristics as well as performance requirements. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For un
36、dated references, the latest edition of the referenced document (including any amendments) applies. SANS 21138-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 21138-1:2007(E) 2 ISO 2007 All rights reservedISO 472, Plastics Vocabular
37、y ISO 580:2005, Plastics piping and ducting systems Injection-moulded thermoplastics fittings Methods for visually assessing the effects of heating ISO 1043-1:2001, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics ISO 1133:2005, Plastics Determination o
38、f the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method ISO 1167-2, Thermoplastics pipes, fittings and asse
39、mblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces ISO 1183-1, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method ISO 2505, Thermop
40、lastics pipes Longitudinal reversion Test method and parameters ISO 2507-1, Thermoplastics pipes and fittings Vicat softening temperature Part 1: General test method ISO 2507-2, Thermoplastics pipes and fittings Vicat softening temperature Part 2: Test conditions for unplasticized poly(vinyl chlorid
41、e) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly(vinyl chloride) (PVC-HI) pipes ISO 3126, Plastics piping systems Plastics components Determination of dimensions ISO 3127, Thermoplastics pipes Determination of resistance to external blows
42、Round-the-clock method ISO 4435, Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U) ISO 8772, Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE) ISO 8773, Plastics piping systems for non-pres
43、sure underground drainage and sewerage Polypropylene (PP) ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes Dichloromethane resistance at specified temperature (DCMT) Test method ISO 9967, Thermoplastics pipes Determination of creep ratio ISO 9969, Thermoplastics pipes Determination of ring
44、 stiffness ISO 11173, Thermoplastics pipes Determination of resistance to external blows Staircase method ISO 11357-6, Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) ISO 11922-1:199
45、7, Thermoplastics pipes for the conveyance of fluids Dimensions and tolerances Part 1: Metric series ISO 12091:1995, Structured-wall thermoplastics pipes Oven test ISO 13967, Thermoplastics fittings Determination of ring stiffness SANS 21138-1:2008This s tandard may only be used and printed by appro
46、ved subscription and freemailing clients of the SABS .ISO 21138-1:2007(E) ISO 2007 All rights reserved 3ISO 21138-2:2007, Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and po
47、lyethylene (PE) Part 2: Pipes and fittings with smooth external surface, Type A ISO 21138-3:2007, Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 3:
48、Pipes and fittings with non-smooth external surface, Type B EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage app
49、lications Part 2: Thermoplastic elastomers EN 681-4, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 4: Cast polyurethane sealing elements EN 1053, Plastics piping systems Thermoplastics piping systems for non-pressure applications Test method for watertightness EN 1277, Plastics piping systems Thermoplastics piping systems for buried non-pressure applicatio
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1