SANS 21138-3-2008 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U) polyprop an.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21749-5 SANS 21138-3:2008Edition 1ISO 21138-3:2007Edition 1SOUTH AFRICAN NATIONAL STANDARD Plastics piping systems for non-pressure underg

4、round drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 3: Pipes and fittings with non-smooth external surface, Type B This national standard is the identical implementation of ISO 21138-3:2007 and is ado

5、pted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 21138-3:2008 Edition 1 ISO 21138-3:2007 Edition 1 Table o

6、f changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS SC 138H, Water and sanitation Equipment and systems Plastics pipes and fittings, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/T

7、BT agreement. This document was published in August 2008. Reference numberISO 21138-3:2007(E)ISO 2007INTERNATIONAL STANDARD ISO21138-3First edition2007-10-15Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride)

8、 (PVC-U), polypropylene (PP) and polyethylene (PE) Part 3: Pipes and fittings with non-smooth external surface, Type B Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement sans pression enterrs Systmes de canalisations parois structures en poly(chlorure de v

9、inyle) non plastifi (PVC-U), polypropylne (PP) et polythylne (PE) Partie 3: Tubes et raccords avec une surface externe non lisse, type B SANS 21138-3:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 21138-3:2007(E) PDF disclaimer This

10、PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept there

11、in the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the

12、 PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUME

13、NT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body i

14、n the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reservedSANS 21138-3:2008This s tandard may only be used and printed by approved

15、 subscription and freemailing clients of the SABS .ISO 21138-3:2007(E) ISO 2007 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 2 3 Terms, definitions, symbols and abbreviated terms. 4 3.1 Terms and definitions. 4 3.2 Symbols . 4 3.3 Abbreviated t

16、erms 5 4 Material 5 4.1 General. 5 4.2 Unplasticized poly(vinyl chloride) (PVC-U) 6 4.3 Polypropylene (PP). 7 4.4 Polyethylene (PE) 9 4.5 Sealing ring retaining components. 11 4.6 Sealing rings . 11 4.7 Fused or welded joints. 11 4.8 Adhesives for PVC-U 11 5 Designation of wall construction and exam

17、ples of typical jointing methods 12 5.1 Wall constructions designated as Type B 12 5.2 Designation and design of joints 13 6 General characteristics for pipes and fittings Colour 13 7 Geometrical characteristics. 13 7.1 General. 13 7.2 Dimensions 13 7.3 Types of fitting 17 8 Physical characteristics

18、. 18 8.1 Unplasticized poly(vinyl chloride) (PVC-U)18 8.2 Polypropylene (PP). 19 8.3 Polyethylene (PE) 19 9 Mechanical characteristics 20 9.1 Mechanical characteristics of pipes . 20 9.2 Mechanical characteristics of fittings. 22 10 Performance requirements 24 11 Marking 25 11.1 General. 25 11.2 Min

19、imum required marking 25 Annex A (normative) Virgin PVC-U material 27 Annex B (normative) Utilization of non-virgin PVC-U material 28 Annex C (normative) Virgin PP material 31 Annex D (normative) Utilization of non-virgin PP material 32 Annex E (normative) Virgin PE material 34 Annex F (normative) U

20、tilization of non-virgin PE material 35 Annex G (informative) Survey of possible use of reprocessable and recyclable material. 38 Bibliography . 39 SANS 21138-3:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 21138-3:2007(E) iv ISO 20

21、07 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a

22、 subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commissio

23、n (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical co

24、mmittees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall no

25、t be held responsible for identifying any or all such patent rights. ISO 21138-3 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 1, Plastics pipes and fittings for soil, waste and drainage (including land drainage). ISO

26、 21138 consists of the following parts, under the general title Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE): Part 1: Material specifications and perfo

27、rmance criteria for pipes, fittings and system Part 2: Pipes and fittings with smooth external surface, Type A Part 3: Pipes and fittings with non-smooth external surface, Type B SANS 21138-3:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS

28、 .ISO 21138-3:2007(E) ISO 2007 All rights reserved vIntroduction ISO 21138 is the system standard covering the plastics piping systems for non-pressure underground drainage and sewerage, in particular thermoplastics structured-wall piping systems. SANS 21138-3:2008This s tandard may only be used and

29、 printed by approved subscription and freemailing clients of the SABS .SANS 21138-3:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL STANDARD ISO 21138-3:2007(E) ISO 2007 All rights reserved 1Plastics piping systems for non-p

30、ressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 3: Pipes and fittings with non-smooth external surface, Type B 1 Scope This part of ISO 21138, together with ISO 21138-1, specifies th

31、e definitions and requirements for pipes with a non-smooth external surface (Type B), fittings and systems based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems in the field of non-pressure systems for underground drainage and se

32、werage. NOTE 1 These pipes, fittings and the system can be used for highway drainage and surface water. This part of ISO 21138 specifically refers to PVC, PP and PE materials. NOTE 2 Other thermoplastic materials may be added via an addendum. This part of ISO 21138 specifies test methods and test pa

33、rameters. This part of ISO 21138 covers a range of pipe and fitting sizes, materials, pipe constructions and nominal ring stiffnesses, and gives recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, ta

34、king into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with ISO 21138-1, this part of ISO 21138 is applicable to PVC-U, PP and PE structured-wall pipes and fittings, to their joints and to joints with components of ot

35、her plastics and non-plastics materials intended to be used for buried piping systems for the transport of drainage and sewage. It is applicable to PVC-U, PP and PE structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joi

36、nts. NOTE 4 Pipes, fittings and other components conforming to any plastics product standards referred to in Clause 2 can be used with pipes and fittings conforming to this part of ISO 21138, when they conform to the requirements for joint dimensions given in parts 2 and 3 of this International Stan

37、dard and to the performance requirements given in Clause 10. NOTE 5 For dimensions larger than DN/OD 1200 or DN/ID 1200 this standard can serve as a general guide regarding appearance, colour, physical and mechanical characteristics as well as performance requirements. Test methods are not included

38、in this document. SANS 21138-3:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 21138-3:2007(E) 2 ISO 2007 All rights reserved2 Normative references The following referenced documents are indispensable for the application of this docum

39、ent. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 178, Plastics Determination of flexural properties ISO 306:1994, Plastics Thermoplastic materials Determination of Vicat softening

40、temperature (VST) ISO 527-2:1993, Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics ISO 580:2005, Plastics piping and ducting systems Injection-moulded thermoplastics fittings Methods for visually assessing the effects of heating ISO 1133:2005,

41、Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method ISO 1167-2, Thermoplastics

42、pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces ISO 1183-1, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration

43、method ISO 2507-1, Thermoplastics pipes and fittings Vicat softening temperature Part 1: General test method ISO 2507-2, Thermoplastics pipes and fittings Vicat softening temperature Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pi

44、pes and fittings and for high impact resistance poly(vinyl chloride) (PVC-Hi) pipes ISO 3126, Plastics piping systems Plastics components Determination of dimensions ISO 3127, Thermoplastics pipes Determination of resistance to external blows Round-the-clock method ISO 3451-1:1997, Plastics Determin

45、ation of ash Part 1: General methods ISO 4435:2003, Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U) ISO 8772:2006, Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE) ISO 8773:2006, Plastic

46、s piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes Dichloromethane resistance at specified temperature (DCMT) Test method ISO 9967, Thermoplastics pipes Determination of creep ratio ISO 9969, Thermoplastic

47、s pipes Determination of ring stiffness ISO 11173, Thermoplastics pipes Determination of resistance to external blows Staircase method SANS 21138-3:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 21138-3:2007(E) ISO 2007 All rights re

48、served 3ISO 11357-6, Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) ISO 12091, Structured-wall thermoplastics pipes Oven test ISO 13967, Thermoplastics fittings Determination of rin

49、g stiffness ISO 21138-1, Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system ISO 21138-2, Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticize