SANS 24734-2009 Information technology - Office equipment - Method for measuring digital printing productivity《信息技术 办公设备 数字打印能力的测量方法》.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23439-3 SANS 24734:2009Edition 1ISO/IEC 24734:2009Edition 1SOUTH AFRICAN NATIONAL STANDARD Information technology Office equipment Method

4、for measuring digital printing productivity This national standard is the identical implementation of ISO/IEC 24734:2009 and is adopted with the permission of the International Organization for Standardization and the International Electrotechnical Commission. Published by SABS Standards Division 1

5、Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 24734:2009 Edition 1 ISO/IEC 24734:2009 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS T

6、C 71, Information technology, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in December 2009. Reference numberISO/IEC 24734:2009(E)ISO/IEC 2009INTERNATIONAL STANDARD ISO/IEC24734First edition2009-03

7、-01Information technology Office equipment Method for measuring digital printing productivity Technologies de linformation quipements de bureau Mthode de mesure de la productivit dimpression numrique SANS 24734:2009This s tandard may only be used and printed by approved subscription and freemailing

8、clients of the SABS .ISO/IEC 24734:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer perform

9、ing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF

10、file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Sec

11、retariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in

12、 writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2009 All rights reservedS

13、ANS 24734:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO/IEC 24734:2009(E) ISO/IEC 2009 All rights reserved iiiContents Page Foreword. v Introduction . vi 1 Scope . 1 2 Terms and definitions. 1 3 Test Parameters and Conditions. 5 3.1

14、 Test Platform . 5 3.2 Test Platform Test Setup Procedures. 5 3.2.1 Initial Platform Setup 5 3.2.2 Creation of Disk Image of Test Platform (optional). 5 3.2.3 Initial Test State 5 3.3 Printing Device System Setup. 5 3.4 Printing Device Connection. 6 3.5 Printing Device Condition 6 3.6 Sample Size .

15、7 3.7 Paper 7 3.8 Maintenance 7 3.9 Test Files, Test Suites and Software Applications 7 3.10 Environment 8 3.11 Voltage . 8 4 Test Method. 8 4.1 Test Measurement Procedure . 8 4.2 Test Method Process 12 4.2.1 Suggested Test Method Process Flow Chart 12 4.2.2 Estimating the Set Count . 13 4.2.3 5% Co

16、nsistency Criteria. 13 4.3 Category Tests 13 4.3.1 Office Test . 14 4.3.2 Advertising and Graphics Test 16 4.4 Feature Performance Test . 18 4.5 Optional Special Tests . 19 5 Calculations and Treatment of Data . 19 5.1 Category Tests 20 5.1.1 1 Set Test . 20 5.1.2 1 Set + 30 Seconds Test . 20 5.1.3

17、1 Set + 4 Minutes Test 20 5.2 Feature Performance Test . 21 5.2.1 1 Set Test . 21 5.2.2 1 Set + 30 Seconds Test . 21 6 Presentation of Results 22 6.1 Category Tests 22 6.2 Feature Performance Tests . 26 Annex A (normative) Test platform system parameters that may affect digital printing productivity

18、 measurements. 27 Annex B (normative) Test Suites 31 Annex C (informative) Report Presentation. 36 Annex D (informative) An example of printing device and test settings to record . 40 SANS 24734:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the S

19、ABS .ISO/IEC 24734:2009(E) iv ISO/IEC 2009 All rights reservedAnnex E (informative) An example of a Full Detailed Report. 41 Bibliography . 44 SANS 24734:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO/IEC 24734:2009(E) ISO/IEC 2009 A

20、ll rights reserved vForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Stan

21、dards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and

22、 IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee

23、is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the pos

24、sibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 24734 was prepared by Technical Committee ISO/TC JTC1, Information technology, Subcommittee SC 28, Office equipmen

25、t. SANS 24734:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO/IEC 24734:2009(E) vi ISO/IEC 2009 All rights reservedIntroduction Many digital printing devices produce printed pages at a different rate than their nominal speed when runn

26、ing with different modes (simplex, duplex, print quality modes), different substrate weight, system environments, applications and file content, and finishing options. The degree to which a reduction in productivity is experienced depends significantly on multiple parameters of the job workflow. The

27、 most dominant of the parameters of the job workflow are: system environment, application, and job characteristics such as the number of pages in a set to be printed, single-sided or double-sided output pages, quality mode, number of print sets to be produced, substrate weight/size used, and finishi

28、ng options, and job content complexities such as monochrome vs. colour, text/vector vs. raster, page scaling and colour conversion. The existing International Standards (ISO/IEC 10561) only address printing throughput for Class 1 and Class 2 printers and (ISO/IEC 14545) only addresses analog copier

29、productivity, therefore both are not suitable for comparing colour printing devices or high-speed page-oriented printing devices with many finishing options and connectivity configurations. This International Standard provides a general method for measuring the productivity when the above-mentioned

30、job workflow parameters for digital printing devices are taken into consideration. This International Standard also includes a suite of test files, test-platform (hardware and software) setup guidelines, and a procedure to be used for measuring digital printing productivity. It allows manufacturers

31、and buyers of digital printing devices to describe the productivity of various digital printing devices with respect to representative office usage patterns. SANS 24734:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL STANDAR

32、D ISO/IEC 24734:2009(E) ISO/IEC 2009 All rights reserved 1Information technology Office equipment Method for measuring digital printing productivity 1 Scope This International Standard specifies a method for measuring the productivity of digital printing devices with various office applications and

33、print job characteristics. This International Standard is applicable to digital printing devices, including single-function and multi-function devices, regardless of print technology (e.g. inkjet, laser). Devices can be equipped with a range of paper feed and finishing options either directly connec

34、ted to the computer system or via a network. It is intended to be used for black and white (B Office category and Advertising and Graphics category, whereby the Office Category test is used to test and report FSOT, ESAT and EFTP using content from typical office applications and the Advertising and

35、Graphics Category test is used to test and report FSOT, ESAT and EFTP using applications and files representing more complexity, higher coverage and a higher ratio of image and graphic content such as pictures, gradients and embedded elements SANS 24734:2009This s tandard may only be used and printe

36、d by approved subscription and freemailing clients of the SABS .ISO/IEC 24734:2009(E) 2 ISO/IEC 2009 All rights reserved2.2 collation printing devices ability to produce multiple hard copies of an electronic document in repeating original order, such as 1234, 1234, 1234.etc, which may be achieved th

37、rough either software features that ensure proper output order or via a hardware finishing device 2.3 default driver printing device driver that is automatically selected as the default per the manufacturers installation procedure 2.4 duplex printing printing where the printing device can make a num

38、ber of prints with the printing being done to both sides of the sheet NOTE Other equivalent terms are “two-sided printing” or “two-sided perfecting”. 2.5 EFTP effective throughput average speed at which a device produces pages measured from the initiation of the job through the complete exit of the

39、last page of the last test set NOTE EFTP is expressed in images per minute (ipm). EFTP can be affected by the digital processing time of the test set as well as the run time of the test set. 2.6 ESAT estimated saturated throughput rate at which a device produces pages measured from the complete exit

40、 of the last page of the first test set through the complete exit of the last page of the last test set NOTE ESAT is expressed in images per minute (ipm). 2.7 feature performance percentage ratio of the printing performance (such as FSOT and ESAT) with the subject feature ON versus the printing devi

41、ce default baseline performance (without the subject feature ON) 2.8 feature performance test optional test used to evaluate productivity changes with various printing and finishing features enabled NOTE The feature performance test suite is run with default printing system settings to establish a b

42、ase line, and then with the selected feature (e.g. stapling) ON, for comparison. 2.9 FSOT first set out time number of seconds between the initiation of the job to the complete exit of the last page of the first test set 2.10 full detailed report presentation of information including machine setup a

43、nd measured test results 2.11 full report presentation of results including the FSOT, EFTP and ESAT values for each file tested for a given category or feature test as well as the calculated averages for the overall FSOT, EFTP and ESAT values SANS 24734:2009This s tandard may only be used and printe

44、d by approved subscription and freemailing clients of the SABS .ISO/IEC 24734:2009(E) ISO/IEC 2009 All rights reserved 32.12 host-based controller printing devices with a host-based controller page description interpreter and RIP reside in the host computer and these processes convert the PDL into a

45、 simplified format such as a raster bitmap, and the simplified data are then sent to the printing device NOTE Most of the data and images processing is done on the host computer side. The performance of the printing device depends upon the whole system the host computer, the data transfer, and the p

46、rinting device. 2.13 initial installation state state of the test platform after the installation and configuration of the operating system and applications but before the installation of unique software, e.g. print driver for the printing device under test 2.14 input image equivalent number of orig

47、inal electronic input images printed independent of the number of hardcopy output sheets the images are printed on NOTE Input image equivalent is expressed in terms of the equivalent number of images input from the source test file. For example, if two A4-sized input images from the test file are pr

48、inted on one-side of an A3 page in simplex printing, the output printed on this A3 page is 2 A4 input image equivalent. For another example, if four A4-sized input images from the test file are printed in reduction on one-side of an A4 page in a 4-up mode in simplex printing, the output printed on t

49、his A4 page is 4 A4 input image equivalent. 2.15 interface/network interface between the host and the printing device, such as a direct (via parallel, serial, USB, Firewire or wireless) or an indirect (via network router/server) connection 2.16 LSOT last set out time number of seconds between the initiation of the job to the complete exit of the last page of the last test set 2.17 nominal printing speed printing rate, excluding time to first page printed, and measured when producing pages in a continuous printing