SANS 300430-2005 Fixed Radio Systems Point-to-point equipment Parameters for radio systems for the transmission of STM-1 digital signals operating in the 18 GHz frequency band with.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 33.040.20; 33.060.30 ISBN 0-626-17390-6 SANS 300430:2005Edition 1 ETSI EN 300430:2002Edition V1.4.1SOUTH AFRICAN NATIONAL STANDARD Fixed Radio System

4、s; Point-to-point equipment; Parameters for radio systems for the transmission of STM-1 digital signals operating in the 18 GHz frequency band with channel spacing of 55 MHz and 27,5 MHz This national standard is the identical implementation of ETSI EN 300430:2002 and is adopted with the permission

5、of the European Telecommunications Standards Institute. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 300430:2005 Edition 1 ETSI EN 300430:200

6、2 Edition V1.4.1 Table of changes Change No. Date Scope Abstract Specifies parameters for high capacity STM-1 digital radio-relay systems designed to operate in the 17,7 GHz to 19,7 GHz band. The channel spacing between adjacent co-polar channels shall be 55 MHz or 27,5 MHz. Keywords architecture, D

7、RRS, PDH, point-to-point, SDH, STM, transmission. National foreword This South African standard was approved by National Committee StanSA TC 74, Communication technology, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. In South Africa, sp

8、ectrum band plans are regulated by the Independent Communications Authority of South Africa (ICASA). The South African Table of Frequency Allocations is obligatory for South Africa and will override any reference to frequency ranges as mentioned in this standard. ETSl EN 300 430 1.4.1 (2002-07) Euro

9、pean Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; Parameters for radio systems for the transmission of STM-1 digital signals operating in the 18 GHz frequency band with channel spacing of 55 MHz and 27,5 MHz ETSl EN 300 430 V1.4.1 (2002-07) Reference RENITM-041

10、49-4 Keywords architecture. DRRS. PDH. oint-to-oint. SDH, STM, transmssion ETSl 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association a but non lucratif enregistree a la Sous-Prefecture de Gras

11、se (06) No 7803188 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the

12、reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSl printers of the PDF version kept on a specific network drive within ETSl Secretariat. Users of the present document should be aware that the document may be subject to revision or

13、 change of status. Information on the current status of this and other ETSl documents is available at http:/portal.etsi.or/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.fr Covriaht Notification No part may be reproduced except as authorized by writ

14、ten permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2002, All rights reserved. DECT, PLUGTESTS UMTS are Trade Marks of ETSl registered for the benefit of its Members. T!PWON and the TlPWQN logo are Trade M

15、arks currently being registered by ETSl for the benefit of its Members. GPP is a Trade Mark of ETSl registered for the benefit of its Members and of the 3GPP Organizational Partners. Contents Intellectual Property Rights 5 Foreword . 5 1 Scope 6 2 References 7 . 3 Symbols and abbreviations 9 3.1 Sym

16、bols 9 3.2 . . Abbreviations . 9 General characteristics . 10 Frequency bands and channel arrangements 10 Channel arrangements . 10 Channel spacing for systems operating on the same route 10 Compatibility requirements between systems 10 Performance and availability requirements 10 Environmental cond

17、itions . 11 Equipment within weather protected locations (indoor locations) 11 Equipment for non-weather protected locations (outdoor locations) 11 Power supply 11 Electromagnetic compatibility 11 System block diagram 12 Telecommunications Management Network (TMN) interface . 12 Branchinglfeederlant

18、enna characteristics . 12 Antenna radiation patterns 12 Antenna cross-Polar Discrimination (XPD) . 12 Antenna Inter-Port Isolation (IPI) . 12 Waveguide flanges (or other connectors) . 13 Return loss 13 5 System Parameters . 13 5.1 Transmission capacity 13 5.2 Baseband parameters 13 5.2.1 Plesiochron

19、ous interfaces . 13 5.2.2 SDH baseband interface 13 5.3 Transmitter characteristics 13 5.3.1 Transmitter power range . 14 5.3.2 Transmit power and frequency control . 14 5.3.2.1 Automatic Transmit Power Control (ATPC) 14 5.3.2.2 Remote Transmit Power Control (RTPC) . 14 5.3.2.3 Remote Frequency Cont

20、rol (RFC) 14 5.3.3 Transmitter output power tolerance 15 5.3.4 Transmit Local Oscillator (LO) frequency arrangements 15 5.3.5 RF spectrum mask . 15 5.3.6 Discrete CW lines exceeding the spectrum mask limit . 18 5.3.6.1 Spectral lines at the symbol rate 18 5.3.6.2 Other spectral lines 18 5.3.7 Spurio

21、us emissions . 19 5.3.7.1 Spurious emissions-external 19 5.3.7.2 Spurious emissions-internal 20 5.3.8 Radio frequency tolerance 20 5.4 Receiver characteristics 20 5.4.1 Input level range . 20 5.4.2 Receiver image rejection 20 . . 5.4.3 Spurious emissions-external . 21 . . 5.4.4 Spurious emissions-in

22、ternal 21 5.5 System performance without diversity . 21 4 ETSl EN 300 430 V1.4.1 (2002-07) 5.5.1 BER as a function of Receiver input Signal Level (RSL) . 21 . 5.5.2 Equipment Residual BER 22 5.5.3 Interference sensitivity 22 . 5.5.3.1 Co-channel interference sensitivity 22 . 5.5.3.2 Adjacent channel

23、 interference 22 5.5.3.3 CW spurious interference 23 . 5.5.4 Distortion sensitivity 23 5.6 System characteristics with diversity . 23 Annex A (informative): Additional information 24 . A . 1 Radio frequency channel arrangement 24 A.2 Feederlantenna return loss 24 A.3 Automatic Transmit Power Control

24、 (ATPC) . 25 A.4 Spectrum masks 25 A.5 RBER . 26 . A.6 Co-channel and adjacent channel interference 27 Annex B (normative): System type codes for regulatory procedures 29 Annex C (informative): Bibliography . 30 History 31 ETSl l ntellectual Property Rights IPRs essential or potentially essential to

25、 the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: fTntellectual Property Rights (IPRs); Essential, orpotentially Essential, IPRs notlJied to ET

26、SI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:llwebapp.etsi.orglIPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be give

27、n as to the existence of other IPRs not referenced in ETSI SR 000 3 14 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Transmissio

28、n and Multiplexing (TM). The present document contains the minimum technical requirements to ensure compatibility of products and conformance with radio regulations across ETSI member states. Radio terminals from different manufacturers are not required to intenvork at radio frequency (i.e. no commo

29、n air interface). However, terminals may be combined with other manufacturers equipment on a Radio Frequency (RF) branching network for operation on different polarizations. The present document defines the requirements of radio terminal and radio relay equipment and associated interfaces. The requi

30、rements for multiplex, network management and antennalfeeder equipment may be addressed elsewhere. This new version modifies only class 5b spectrum mask giving more allowance for practical implementations, without modifying any other requirements, and proposed design objectives for class 5a BER vers

31、us RSL. National transposition dates Date of adoption of this EN: 12 July 2002 Date of latest announcement of this EN (doa): 3 1 October 2002 Date of latest publication of new National Standard or endorsement of this EN (dople): 30 April 2003 Date of withdrawal of any conflicting National Standard (

32、dow): 30 April 2003 1 Scope The present document specifies parameters for high capacity STM-1 digital radio-relay systems designed to operate in the 17,7 GHz to 19,7 GHz band. The channel spacing between adjacent co-polar channels shall be 55 MHz or 27,5 MHz. Operation in the Adjacent Channel Co-Pol

33、arization (ACCP) mode for class 4 systems and class 5 systems as defined below with orthogonal polarizations or in the alternated cross-polar mode is foreseen. Additionally for class 4 systems, operation in the Co-Channel Dual Polarized (CCDP) mode with orthogonal polarization is also foreseen. The

34、present document covers both single and multi-channel systems. The present document specifies the minimum performance parameters for terrestrial fixed service radio communications equipment operating in the frequency range 17,7 GHz to 19,7 GHz and contains a revision from the previous version, in th

35、e area of: - categorization of previously considered equipments into a new spectrum efficiency class 4; - introduction of unique system type codes for regulatory reference to the various system types detailed in the present document, refer to new annex C and related categories of equipment classes o

36、f spectral efficiency; - new spectrum efficiency class 5 for STM-1 capacity for 27,5 MHz Adjacent Channel Alternate-Polarization (ACAP as class 5a) and Adjacent Channel Co-Polarization (ACCP as class 5b), see examples of the spectrum usage in figures 1.1 a and 1.1 b: Figure 1 - technical specificati

37、ons relevant to the EMC Directive 30, detailed in annex B. The applications of these digital radio-relay systems are anticipated to be in the regional and access networks, at data rates of Synchronous Transport Module, level 1 (STM-1). The parameters to be specified fall into two categories: a) thos

38、e that are required to provide compatibility between channels from different sources of equipment on the same route connected either to: - separate antennas; or - separate polarizations of the same antenna; or - one polarization of one antenna at a frequency separation of 110 MHz or more, enabling,

39、in addition for class 4 equipment only, interworking of different manufacturers equipment at the same Radio Frequency (RF) branching; - this category also includes parameters providing compatibility with the existing radio-relay network. b) parameters defining the transmission quality of the propose

40、d system. The standardization deals with RF and baseband characteristics. Antennalfeeder system requirements are covered in EN 300 833 33. Two possible baseband interfaces for SDH systems have to be considered: one for STM-1 and another for 140 Mbitls signals. The present document does not contain a

41、spects related to test procedures and test conditions, however they are to be found in EN 301 126-1 19. As the maximum transmission rate in a given bandwidth depends on systems spectral efficiency, different classes are defined: - class 4: equipment spectral efficiency based on typically 16 or 32-st

42、ates modulation scheme (e.g. 16-QAM, 32-QAM, or equivalent); - class 5: equipment spectral efficiency based on typically 64 or 128-states modulation scheme (e.g. 64-QAM, 128-QAM, or equivalent). The above classes are indicative only and do not imply any constraint to the actual modulation format, pr

43、ovided that all the requirements in the present document are met. Safety aspects will not be considered in the present document. However compliance to EN 60950-1 28 will be required to comply with Directive 199915lEC 29 (R Environmental conditions and environmental tests for telecommunications equip

44、ment; Part 1 : Classification of environmental conditions“. ETSI ETS 300 019-2 (all parts): “Equipment Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2: Specification of environmental tests“. ETSI ETS 300 132-1: “Equipment Engineering (EE);

45、Power supply interface at the input to telecommunications equipment; Part 1 : Operated by alternating current (ac) derived from direct current (dc) sources“. ETSI EN 300 132-2: “Environmental Engineering (EE); Power supply interface at the input to telecommunications equipment; Part 2: Operated by d

46、irect current (dc)“. ITU-T Recommendation G.703: “Physical/electrical characteristics of hierarchical digital interfaces“. ITU-T Recommendation G.773: “Protocol suites for Q-interfaces for management of transmission systems“. ITU-T Recommendation G.784: “Synchronous digital hierarchy (SDH) managemen

47、t“. ITU-T Recommendation G.821: “Error performance of an international digital connection operating at a bit rate below the primary rate and forming part of an integrated services digital network“. ITU-T Recommendation G.826: “Error performance parameters and objectives for international, constant b

48、it rate digital paths at or above the primary rate“. ITU-T Recommendation G.957: “Optical interfaces for equipments and systems relating to the synchronous digital hierarchy“. ETSI EN 300 385: “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standa

49、rd for fixed radio links and ancillary equipment“. ETSI EN 301 126-1: “Fixed Radio Systems; Conformance testing; Part 1: Point-to-point equipment - Definitions, general requirements and test procedures“. ETSI TR 101 036-1: “Fixed Radio Systems; Point-to-point equipment; Generic wordings for standards on digital radio systems characteristics; Part 1: General aspects and point-to-point equipment parameters“. ETSI ETS 300 635: “Transmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH); Radio specific functional blocks for transmission of M x ST