SANS 301428-2008 Satellite Earth Stations and Systems (SES) Harmonized EN for Very Small Aperture Terminal (VSAT) Transmit-only transmit receive or receive-only satellite earth sta b.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21615-3 SANS 301428:2008Edition 2ETSI EN 301428:2006Edition V1.3.1SOUTH AFRICAN NATIONAL STANDARD Satellite Earth Stations and Systems (SE

4、S); Harmonized EN for Very Small Aperture Terminal (VSAT); Transmit-only, transmit/receive or receive-only satellite earth stations operating in the 11/12/14 GHz frequency bands covering essential requirements under article 3.2 of the RHarmonized EN for Very Small Aperture Terminal (VSAT);Transmit-o

5、nly, transmit/receive or receive-only satellite earthstations operating in the 11/12/14 GHz frequency bandscovering essential requirements underarticle 3m2 of the R 31Initial burst transmission 32Justification 32Specification 32Conformance tests 325 Testing for compliance with technical requirements

6、 325.1 Environmental conditions for testing 325.2 Essential radio test suites 32Test methods for the complete VSAT 32General 32Off-axis spurious radiation 33Test method 33Multi-carrier operation 34Up to 1 000 MHz 34Test site 34Measuring receivers 34Procedure 35Above 1 000 MHz 35Identification ofthe

7、significant frequencies ofspurious radiation 35Measurement ofradiated power levels ofidentified spurious radiation 36Measurement ofconducted spurious radiation at the antenna flange 37On-axis spurious radiation for transmit VSAT 38Test method 38Test site 38Method ofmeasurement 38General 38Method ofm

8、easurement at the antenna flange 38Method ofmeasurement with a test antenna 3966.16.26.2.16.2.1.06.2.1.16.2.1.1.16.2.1.1.26.2.1.1.36.2.1.26.2.1.2.16.2.1.2.26.2.1.2.36.36.3.16.3.1.16.3.1.26.3.1.2.16.3.1.2.26.3.1.2.3lETSISANS 301428:2008This s tandard may only be used and printed by approved subscript

9、ion and freemailing clients of the SABS .5 ETSI EN 301 428 V1.3.1 (2006-02)6.46.4.16.4.1.16.4.1.26.4.1.2.16.4.1.2.26.4.1.2.36.4.1.36.4.1.3.16.4.1.3.26.4.1.3.36.4.1.46.4.1.4.16.4.1.4.26.4.1.4.36.4.1.4.46.4.1.4.56.4.1.4.66.4.1.4.76.4.26.56.5.16.66.6.16.76.7.16.7.26.7.36.7.3.16.7.3.1.16.7.3.1.26.7.46.7

10、.4.16.7.56.7.5.16.7.66.7.6.16.7.6.26.7.6.36.7.76.7.7.16.7.86.7.8.16.86.8.16.8.26.8.36.8.46.8.56.8.66.8.7Off-axis e.i.r.p emission density within the band .40Test method 40General 40Transmit output power density 40General 40Test site 40Method ofmeasurement 41Antenna transmit gain 42General 42Test sit

11、e 42Method ofmeasurement 42Antenna transmit radiation patterns .43General 43Test site 43Test arrangement 43Co-polar radiation pattern-azimuth .43Co-polar radiation pattern-elevation .44Cross-polar radiation pattern-azimuth .45Cross-polar radiation pattern-elevation .45Computation ofresults ; 46Carri

12、er suppression 46Test method 46Antenna pointing for transmit VSAT .46Test method 46Class A Control and Monitoring Functions .47General 47Test arrangement 47Control Channels (CC) 48Test method 48Test method for internal CC 48Test method for external CC 49Processor monitoring 49Test method 49Transmit

13、subsystem monitoring 49Test method 49VSAT transmission validation 50Test method for VSAT validation by the CCMF for VSAT using internal CC 50Test method for VSAT validation by receiving station(s) for VSAT using internal Cc. 50Test method for transmission validation for VSAT using external CC 50Rece

14、ption ofcommands from the CCMF 50Test method 50Power-on/Reset 50Test method 50Class B Control and Monitoring Functions 51Test arrangement 51Processor monitoring- Test method 52Transmit subsystem monitoring-Test method 52Power-on/Reset-Test method 53Control Channel (CC) reception-Test method 53Networ

15、k Control commands-Test method 54Initial burst transmission-Test method 567 Test methods for modified VSAT 567.1 General 567.2 Antenna subsystem replacement 57Annex A (normative):Annex B (informative):Annex C (informative):The EN Requirements table (EN-RT) 58Pointing stability methodology 59The EN t

16、itle in the official languages 60ETSISANS 301428:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .6 ETSI EN 301 428 V1.3.1 (2006-02)Annex D (informative): Bibliography 62History 63ETStSANS 301428:2008This s tandard may only be used and pri

17、nted by approved subscription and freemailing clients of the SABS .Intellectual Property Rights7 ETSI EN 301 428 V1.3.1 (2006-02)IPRs essential or potentially essential to the present document may have been declared to ETSI. The informationpertaining to these essential IPRs, ifany, is publicly avail

18、able for ETSI members and non-members, and can be foundin ETSI SR 000314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI inrespect ofETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Webserver (ht

19、tp:/webapp.etsi.onz/IPR/home.asp).Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaranteecan be given as to the existence ofother IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Webserver) which are, or may be, or may b

20、ecome, essential to the present document.ForewordThis Candidate Harmonized European Standard (Telecommunications series) has been produced by ETSI TechnicalCommittee Satellite Earth Stations and Systems (SES).The present document has been produced by ETSI in response to a mandate from the European C

21、ommission issuedunder Directive 98/34/EC 3 (as amended) laying down a procedure for the provision ofinformation in the field oftechnical standards and regulations.The present document is intended to become a Harmonized Standard, the reference ofwhich will be published in theOfficial Journal ofthe Eu

22、ropean Communities referencing the Directive 1999/5/EC 1 ofthe European Parliament andofthe Council of9 March 1999 on radio equipment and telecommunications terminal equipment and the mutualrecognition oftheir conformity (“Rit provides scope for standards to be added:under article 3.2 when new frequ

23、ency bands are agreed; orunder article 3.3 should the Commission take the necessary decisionswithout requiring alteration ofstandards that are already published;it clarifies, simplifies and promotes the usage ofHarmonized Standards as the relevant means ofconformityassessment.Remarks on the present

24、documentThe present document allows the choice ofeither a class A Control and Monitoring system or a class B Control andMonitoring system. The class B system is more suitable for networks comprising very many terminals.The determination ofthe parameters ofthe user earth stations using a given geo-st

25、ationary satellite for the protection ofthe spectrum allocated to that satellite, is considered to be under the responsibility ofthe satellite operator or thesatellite network operators. For this reason the requirement on the cross polarization discrimination which was inTBR 28 (see Bibliography) ha

26、s not been copied in the present document and inter-modulation limits inside the band14,0 GHz to 14,5 GHz are to be determined by system design and are subject to satellite operator specifications.The requirements have been selected to ensure an adequate level ofcompatibility with other radio servic

27、es. The levels,however, do not cover extreme cases which may occur in any location but with a low probability ofoccurrence.The present document may not cover those cases where a potential source ofinterference which is producingindividually repeated transient phenomena or a continuous phenomenon is

28、present, e.g. a radar or broadcast site in thenear vicinity. In such a case it may be necessary to use special protection applied to either the source ofinterference, orthe interfered part or both.The present document does not contain any requirement, recommendation or information about the installa

29、tion oftheVSAT.ETSISANS 301428:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .10 ETSI EN 301 428 V1.3.1 (2006-02)All parts ofthe indoor unit related to reception, processing and presentation ofthe received information except thecontrol c

30、hannel are not within the scope ofthe present document. The syntax ofthe control channel messages is outsidethe scope ofthe present document.ETSISANS 301428:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .1 Scope11 ETSI EN 301 428 V1.3.1

31、(2006-02)The present document applies to Very Small Aperture Terminals (YSATs) which have the following characteristics: The YSAT is operating in one or more frequency ranges in the part ofthe following bands allocatedexclusively to the Fixed Satellite Services (FSS):14,00 GHz to 14,25 GHz (earth-to

32、-space);12,50 GHz to 12,75 GHz (space-to-earth);or in the shared parts ofthe following bands, allocated to the FSS and Fixed Services (FS):14,25 GHz to 14,50 GHz (earth-to-space);10,70 GHz to 11,70 GHz (space-to-earth). The YSAT uses linear polarization. The YSAT operates through a geostationary sat

33、ellite at least 30away from any other geostationary satelliteoperating in the same frequency band and covering the same area. The YSAT antenna diameter does not exceed 3,8 m, or equivalent effective area. The YSAT is either:a transmit only YSAT: designed for transmission only of radio-communications

34、 signals in any of thefrequency bands (earth-to-space) specified above; ora transmit and receive YSAT: designed for transmission and reception ofradio-communications signalsin any ofthe frequency bands specified above; ora receive only YSAT: designed for reception only ofradio-communications signals

35、 in any ofthefrequency bands (space-earth) specified above. The YSAT is designed usually for unattended operation. The YSAT is operating as part ofa satellite network (e.g. star, mesh or point-to-point) used for the distributionand/or exchange ofinformation between users. The transmit-only and trans

36、mit-and-receive YSAT is-controlled and monitored by a Centralized Control andMonitoring Function (CCMF). The CCMF is outside the scope ofthe present document.The present document applies to the YSAT with its ancillary equipment and its various terrestrial ports, and whenoperated within the boundary

37、limits ofthe operational environmental profile declared by the applicant and wheninstalled as required by the applicant by declaration or in the user documentation.The present document is intended to cover the provisions ofDirective 1999/5/EC (R andb) the equipment cannot be used on a stand alone ba

38、sis, to provide user functions independently oftheVSAT; andc) the absence ofthe equipment does not inhibit the operation ofthe VSAT.applicant: manufacturer or his authorized representative within the European Community or the person responsible forplacing the apparatus on the marketcarrier-off radio

39、 state: radio state in which the VSAT may transmit and does not transmit any carrierNOTE I: The phrase “the VSAT may transmit“ means that all the conditions for transmission are satisfied (e.g. in astate where transmissions are permitted and no failure detected).NOTE 2: The existence ofa “Carrier-of

40、f radio state depends on the system oftransmission used. For VSATsdesigned for continuous transmission mode there may be no “Carrier-off radio state.carrier-on radio state: radio state in which the VSAT may transmit and transmits a carrierCentralized Control and Monitoring Functions (CCMF): set offu

41、nctional entities that, at system level, monitor andcontrol the correct operation ofall transmit VSAT in a networkControl Channel (CC): channel or channels by which VSAT receive control information from the CCMFETSISANS 301428:2008This s tandard may only be used and printed by approved subscription

42、and freemailing clients of the SABS .13EIRPmax: maximum e.i.r.p capability ofthe VSAT as declared by the applicantEIRPnom: either:(i) EIRPmax;ETSI EN 301 428 V1.3.1 (2006-02)(ii) or, when uplink power control is implemented, the maximum required e.i.r.p ofthe VSAT under clear skycondition as declare

43、d by the applicant.NOTE: The applicant may declare different values ofEIRPmax and EIRPnom for each combination ofoccupiedbandwidth and transmission parameters (see clause 4.1.3).emissions disabled radio state: radio state in which the VSAT must not transmit a carrierNOTE: This radio state only appli

44、es in certain CMF states as defined in clause 4.1.4. (e.g. before systemmonitoring pass, before the control channel is received, when a failure is detected, when the VSAT iscommanded to disable). The “Emissions disabled“ radio state requires lower unwanted emissions than the“Carrier-off radio state.

45、environmental profile: range ofenvironmental conditions under which equipment within the scope ofEN 301 428 isrequired to comply with the provisions ofEN 301 428external control channel: control channel which is either (i) carried by the VSAT network via the same or anothersatellite, but not within

46、the internal protocol ofthe VSAT system, or (ii) carried by the PSTN or some other meansexternal response channel: response channel which is either (i) carried by the VSAT network via the same or anothersatellite, but not within the internal protocol ofthe VSAT system, or (ii) carried by the PSTN or

47、 some other meansindoor unit: is composed ofthat part ofthe VSAT which is not part ofthe outdoor unit. It is generally installed inside abuilding and is connected to the outdoor unit. The connection cable between the outdoor and indoor unit is consideredpart ofthe indoor unitintegral antenna: antenn

48、a which may not be removed during the tests according to the applicants statementinternal control channel: control channel which is carried by the VSAT network via the same satellite as used fortransmission ofuser data and within the internal protocol structure ofthe VSAT systeminternal response cha

49、nnel: response channel which is carried by the VSAT network via the same satellite as used fortransmission ofuser data and within the internal protocol structure ofthe VSAT systemnetwork: in EN 301 428 a network is any network configuration including star, mesh and point-to-point configurationsnominated bandwidth: bandwidth ofthe VSAT radio frequency transmission is nominated by the applicant.NOTE 1: The nominated bandwidth is centred on the transmit frequency and does not exceed 5 times the occupiedbandwidth.NOTE 2: The nominated bandwidth is wide enough to encompass all spec