SANS 301669-2005 Fixed Radio Systems Point-to-point equipment High capacity digital radio systems carrying STM-4 in two 40 MHz channels or 2 x STM-1 in a 40 MHz channel with altern.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 33.060.30 ISBN 0-626-17414-7 SANS 301669:2005Edition 1ETSI EN 301669:2001Edition V1.2.1SOUTH AFRICAN NATIONAL STANDARD Fixed Radio Systems; Point-to-

4、point equipment; High capacity digital radio systems carrying STM-4 in two 40 MHz channels or 2 x STM-1 in a 40 MHz channel with alternate channel arrangement This national standard is the identical implementation of ETSI EN 301669:2001 and is adopted with the permission of the European Telecommunic

5、ations Standards Institute. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 301669:2005 Edition 1 ETSI EN 301669:2001 Edition V1.2.1 Table of ch

6、anges Change No. Date Scope Abstract Specifies parameters for digital radio-relay systems with Transport Module-level 4 (1 x STM-4) interface, and in addition, optional 140 Mbit/s PDH interfaces. Keywords DRRS, point-to-point, SDH, STM. National foreword This South African standard was approved by N

7、ational Committee StanSA TC 74, Communication technology, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. In South Africa, spectrum band plans are regulated by the Independent Communications Authority of South Africa (ICASA). The South Af

8、rican Table of Frequency Allocations is obligatory for South Africa and will override any reference to frequency ranges as mentioned in this standard. ETS l E N 30 1 669 VI 2.1 (2001-02) European Standard (Telecommunications series) Fixed Radio Systems; Point-to-point equipment; High capacity digita

9、l radio systems carrying STM-4 in two 40 MHz channels or 2 x STM-1 in a 40 MHz channel with alternate channel arrangement ETSl EN 301 669 V1.2.1 (2001-02) Reference RENTTM-04111-08 Keywords DRRS, point-to-point, SDH, STM ETSl 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Siret No 34

10、8 623 562 00017 - NAF 742 C Association a but non lucratif enregistree a la Sous-Prefecture de Grasse (06) No 7803188 Important notice Individual copies of the present document can be downloaded from: htt:/w.etsi.oq The present document may be made available in more than one electronic version or in

11、 print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSl printers of the PDF version kept on a specific network drive within ETSl Secretariat

12、. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSl documents is available at htt:/iwww.etsi.orctb!status/ If you find errors in the present document, send your comment to: editor e

13、tsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Teiecommunications Standards Institute 2001 All rights reserved. 3 ETSl EN 301 669 V1.2.1 (2001-02) Contents

14、 Intellectual Property Rights 5 Foreword 5 1 Scope 6 2 References 7 3 Symbols and abbreviations 9 3.1 Symbols 9 3.2 . . Abbreviations 9 4 Network and system considerations 10 General characteristics 10 Baseband interface 10 Synchronous Digital Hierarchy . 10 . Plesiochronous digital hierarchy 10 Fre

15、quency bands and channel arrangements . 10 4 GHz 11 5 GHz 11 Upper 6 GHz 11 11 GHz 11 Modes of operation 11 . . Environmental conditons 11 Equipment within weather protected locations (indoor locations) I I Equipment for non-weather protected locations (outdoor locations) . 11 Electromagnetic compat

16、ibility . I1 Power supply . 12 Telecommunications Management Network (TMN) interface . 12 System block diagram . 13 Antenna system . 13 . Crosspolar Discrimination (XPD) 13 Intermodulation products 13 Interport isolation . 14 Return loss . 14 Transmitter characteristics 14 Output power 14 Automatic

17、Transmit Power Control (ATPC) 14 RF spectrum mask . 14 Discrete CW lines exceeding the spectrum mask limit . 16 Spectral lines at the symbol rate . 16 Other spectral lines 16 . . Spurious emissions 17 . Spurious emissions . external 17 Spurious emissions . internal 17 Radio frequency tolerance . 17

18、Return loss 17 Receiver characteristics . 18 Receiver image rejection . 18 Spurious emissions 18 Spurious emissions . external . 18 Spurious emissions . internal 18 Input level range 18 Return ioss 18 System characteristics without diversity 19 Equipment background BER 19 ETSl 8.2 BER as a function

19、of receiver input level 19 8.3 Interference sensitivity 19 . 8.3.1 Cochannel interference sensitivity 19 8.3.2 Adjacent channel interference sensitivity 19 8.3.3 CW Spurious Interference 19 8.4 Distortion sensitivity . 20 . 9 System characteristics with diversity 20 9.1 Spacetangle diversity . 20 9.

20、1.1 Differential delay compensation . 20 9.1.2 BER performance 20 9.2 Frequency diversity . 20 Annex A (informative): Additional information 21 . A . 1 ATPC 21 A.2 Differential delay compensation range 21 Annex B (informative): Compatibility . 22 B . 1 Compatibility with analogue channels on the sam

21、e route . 22 B.2 Compatibility with 16 QAM systems on the same route 22 Annex C (informative): Bibliography 24 . History 25 5 ETSl EN 301 669 V1.2.1 (2001-02) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

22、pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 3 14: Yrztellectual Properh, Rights (IPRs); Esserztial, orpoterztially Essential, IPRs rzotified to ETSI in respect of ETSI starzdards“, which is available from the ETS

23、I Secretariat. Latest updates are available on the ETSI Web server (bttp:/li+.etsi.orp/iw). Pursuant to the ETSI IPR Policy. no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 3 14 (or the

24、updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Transmission and Multiplexing (TM). National transposition dates Date of adoption of this

25、EN: 16 February 2001 Date of latest announcement of this EN (doa): 31 May 2001 Date of latest publication of new National Standard or endorsement of this EN (dople): 30 November 2001 Date of withdrawal of any conflicting National Standard (dow): 30 November 200 1 6 ETSl EN 301 669 V1.2.1 (2001-02) 1

26、 Scope The present document specifies parameters for digital radio-relay systems with Transport Module-level 4, (1 x STM-4), interface, and in addition. optional 140 Mbitts PDH interfaces. The present document is applicable to systems carrying an STM-4 signal over a pair of RF channels each with a c

27、apacity of 2 x Synchronous Transport Module-level 1, (2 x STM-I), designed to operate in defined bands utilizing 40 MHz between adjacent crosspolar channels. Optionally, a single RF channel can be used to transport 2 x Synchronous Transport Module-level 1, (2 x STM-1). signals. The parameters specif

28、ied fall into two categories: a) those required to provide compatibility between channels from different sources of equipment on the same route, connected either to separate antennas, or to separate polarizations of the same antenna. This category also includes parameters providing compatibility wit

29、h the existing radio-relay network: b) parameters defining the transmission quality of the proposed systems. Compatibility requirements with analogue and digital systems on the same hop and at nodes are examined. However, they cannot be defined with exactness due to the fact that analogue systems an

30、d some digital systems are not standardized. Compatibility requirements are, therefore, limited to allowing the operation of digital and analogue channels on separate ports of the same antenna (see annex B). The standardization includes the following specifications: a) transmitter and receiver chara

31、cteristics; b) baseband and Radio Frequency (RF) interface characteristics; c) diversity system characteristics; d) STM-4, or STM-1 baseband transport interface; e) PDH baseband transport interfaces mapped onto an SDH frame. Baseband interfaces have to be considered for STM-4 signals and STM-1 signa

32、ls are in accordance with ITU-T Recommendations 6.957 37 and G.707 33 respectively. Safety aspects are outside the mandate of ETSI and they will not be considered in the present document. 2 References The following documents contain provisions which, through reference in this text, constitute provis

33、ions of the present document. References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. I CEPTIERC Recommendation 12-

34、08: “Harmonised radio frequency channel arrangements and block allocations for low, medium and high capacity systems in the band 3600 MHz to 4200 MHz“. 21 CEPTIERC Recommendation 14-02: “Radio-frequency channel arrangements for medium and high capacity analogue or high capacity digital radio-relay s

35、ystems operating in the band 6 425 MHz - 7 125 MHz“. PI ETSI EN 301 390: “Fixed Radio Systems; Point-to-point and Point-to-Multipoint Systems; Spurious emissions and receiver immunity at equipmentlantenna port of Digital Fixed Radio Systems“. 41 ETSI EN 300 645 (V1.2.1): “Telecommunications Manageme

36、nt Network (TMN); Synchronous Digital Hierarchy (SDH) radio relay equipment; Information model for use on Q interfaces“. L-51 ETSI ETR 019: “Transmission and Multiplexing (TM); Specification of new generation high-capacity digital radio systems carrying 2 x STM-1 Synchronous Digital Hierarchy (SDH)

37、signals in frequency bands with 40 MHz channel spacing“. 6 ETSI ETS 300 019 (all parts): “Equipment engineering (EE); Environmental conditions and environmental tests for telecommunications equipment“. 71 ETSI ETS 300 132-1: “Equipment Engineering (EE); Power supply interface at the input to telecom

38、munications equipment; Part 1: Operated by alternating current (ac) derived from direct current (dc) sources“. 8 ETSI ETS 300 132-2: “Equipment Engineering (EE); Power supply interface at the input to telecommunications equipment; Part 2: Operated by direct current (dc)“. 191 ETSI EN 300 385: “Elect

39、romagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for fixed radio links and ancillary equipment“. 11 01 ETSI EN 300 417-1-1: “Transmission and Multiplexing (TM); Generic requirements of transport functionality of equipment; Part 1-1 : Generic pro

40、cesses and performance“. I 11 ETSI EN 300 417-1-2: “Transmission and Multiplexing (TM); Generic requirements of transport functionality of equipment: Part 1-2: General information about Implementation Conformance Statement (ICS) proforma“. I21 ETSI EN 300 41 7-2-1: “Transmission and Multiplexing (TM

41、): Generic requirements of transport functionality of equipment; Part 2-1: Synchronous Digital Hierarchy (SDH) and Plesiochronous Digital Hierarchy (PDH) physical section layer functions“. I31 ETSI EN 300 417-2-2: “Transmission and Multiplexing (TM); Generic requirements of transport functionalit) o

42、f equipment; Part 2-2: Synchronous Digital Hierarchy (SDH) and Plesiochronous Digital Herarchy (PDH) physical section layer functons; Implementation Conformance Statement (ICS) proforma specification“. 1141 ETSI EN 300 417-3-1 : “Transmission and Multiplexing (TM); Generic requirements of transport

43、functionality of equipment; Part 3-1 : Synchronous Transport Module-N (STM-N) regenerator and multiplex section layer functions“. 8 ETSl EN 301 669 V1.2.1 (2001-02) ETSI EN 300 41 7-3-2: “Transmission and Multiplexing (TM): Generic requirements of transport functionality of equipment; Part 3-2: Sync

44、hronous Transport Module-N (STM-N) regenerator and multiplex section layer functions: Implementation Conformance Statement (ICS) proforma specification “. ETSI EN 300 417-4-1: “Transmission and Multiplexing (TM); Generic requirements of transport functionality of equipment; Part 4-1: Synchronous Dig

45、ital Hierarchy (SDH) path layer functions“. ETSI EN 300 4 17-5- 1 : “Transmission and Multiplexing (TM); Generic requirements of transport functionality of equipment; Part 5-1: Plesiochronous Digital Hierarchy (PDH) path layer functions“. ETSI EN 300 41 7-6-1: “Transmission and Multiplexing (TM); Ge

46、neric requirements of transport functionality of equipment; Part 6-1: Synchronization layer functions“. ETSI ETS 300 635: “Transmission and Multiplexing (TM); Synchronous Digital Hierarchy (SDH); Radio specific functional blocks for transmission of M x STM-Nu. ETSI EN 300 833: “Fixed Radio Systems:

47、Point-to-point Antennas; Antennas for point-to-point fixed radio systems operating in the frequency band 3 GHz to 60 GHz“. ETSI EN 301 167: “Transmission and Multiplexing (TM); Management of Synchronous Digital Hierarchy (SDH) transmission equipment; Fault management and performance monitoring; Func

48、tional description“. ITU-R Recommendation F.1092-1: “Error performance objectives for constant bit rate digital path at or above the primary rate carried by digital radio-relay systems which may form part of the international portion of a 27 500 km hypothetical reference path“. ITU-R Recommendation

49、F. 1099-3: “Radio-frequency channel arrangements for high-capacity digital radio-relay systems in the 5 GHz (4 400 MHz to 5 000 MHz) band“. ITU-R Recommendation F. 11 89-1 : “Error performance objectives for constant bit rate digital paths at or above the primary rate carried by digital radio-relay systems which may form part or all of the national portion of a 27 500 km hypothetical reference path“. ITU-R Recommendation F. 1 191 -1 : “Bandwidths and unwanted emissions of digital radio-relay systems“. ITU-R Recommendation F.384-7: “Radio-frequency channel a