SANS 5828-2004 Resistance welding equipment - Secondary connecting cables with terminals connected to water-cooled lugs - Dimensions and characteristics《电阻焊接设备 水冷耳接线柱辅助连接电缆 尺寸及特点》.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 25.160.30 ISBN 0-626-15918-0 SANS 5828:2004 Edition 2 ISO 5828:2001 Edition 2SOUTH AFRICAN NATIONAL STANDARD Resistance welding equipment Secondary c

4、onnecting cables with terminals connected to water-cooled lugs Dimensions and characteristics This national standard is the identical implementation of ISO 5828:2001 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lat

5、egan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code +27 12 www.stansa.co.za Standards South Africa This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 5828:2004 Edition 2 ISO 5828:2001 Edi

6、tion 2 Table of changes Change No. Date Scope Abstract Specifies the dimensions and characteristics of secondary connecting cables which are air-cooled over their length and with terminals connected to water-cooled lugs. Keywords designation, dimensions, electric cables, endurance testing, resistanc

7、e welding equipment, specifications, welding, welding equipment. National foreword This South African standard was approved by National Committee StanSA TC 5120.08, Welding and allied processes, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreem

8、ent. This SANS edition cancels and replaces SABS edition 1 (SABS ISO 5828:1983). This standard may only be used and printed by approved subscription and freemailing clients of the SABS.Reference number ISO 5828:2001(E) ISO 2001 INTERNATIONAL STANDARD ISO 5828 Second edition 2001-03-01 Resistance wel

9、ding equipment Secondary connecting cables with terminals connected to water-cooled lugs Dimensions and characteristics quipements de soudage par rsistance Cbles de raccordement secondaires avec extrmits raccordes des plages refroidies par eau Dimensions et caractristiquesThis standard may only be u

10、sed and printed by approved subscription and freemailing clients of the SABS.ISO 5828:2001(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded ar

11、e licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Detail

12、s of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem rel

13、ating to it is found, please inform the Central Secretariat at the address given below. ISO 2001 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, wit

14、hout permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2001 All rights

15、 reservedThis standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 5828:2001(E) ISO 2001 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodi

16、es). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and

17、non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, P

18、art 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of

19、 this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 5828 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 6, Resistance welding. This

20、second edition cancels and replaces the first edition (ISO 5828:1983) which has been technically revised. In particular it has been extended to take in lowly flexible cables with requirements for type LF cables given in clause 6. The values of the chemical composition and electrical properties are i

21、dentical to those of Cu-ETP and Cu-FRHC, defined in ISO 1337:1980 which has been withdrawn.This standard may only be used and printed by approved subscription and freemailing clients of the SABS. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.

22、INTERNATIONAL STANDARD ISO 5828:2001(E) ISO 2001 All rights reserved 1 Resistance welding equipment Secondary connecting cables with terminals connected to water-cooled lugs Dimensions and characteristics 1 Scope This International Standard specifies dimensions and characteristics of secondary conne

23、cting cables which are air- cooled over their length and with terminals connected to water-cooled lugs. The secondary connecting cables are used for connection between the secondary terminals of a welding transformer and the electrode holders. 2 Classification The secondary connecting cables are cla

24、ssified into low flexibility (LF), flexible (F) and highly flexible types (HF) depending on diameter of wire (see clause 6). 3 Dimensions The dimensions of the secondary connecting cables shall be as given in Figure 1 and Table 1. Dimensions in millimetres, surface roughness in micrometres Key 1 Ter

25、minal 2 Cable 3 Insulation cover 4 Marking Figure 1 DimensionsThis standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 5828:2001(E) 2 ISO 2001 All rights reserved Table 1 Dimensions Dimensions in millimetres Section, mm 2 Dimension 200 250 315 400 5

26、00 630 800 a 11 13 16 20 24 24 32 b 32 32 32 32 32 38 38 D 36 38 40 45 50 55 65 L a Permissible permanent current I 2p ,A b 160 (180) 200 (224) 250 (280) 315 (355) 400 (450) 500 (560) 630 25 00 23 60 22 40 21 20 20 00 19 00 18 00 17 00 16 00 15 00 14 00 28 00 26 50 25 00 23 60 22 40 21 20 20 00 19 0

27、0 18 00 17 00 16 00 31 50 30 00 28 00 26 50 25 00 23 60 22 40 21 20 20 00 19 00 18 00 35 50 33 50 31 50 30 00 28 00 26 50 25 00 23 60 22 40 21 20 20 00 19 00 18 00 40 00 37 50 35 50 33 50 31 50 30 00 28 00 26 50 25 00 23 60 22 40 21 20 20 00 37 50 35 50 33 50 31 50 30 00 28 00 26 50 25 00 23 60 22 4

28、0 40 00 37 50 35 50 33 50 31 50 30 00 28 00 26 50 25 00 NOTE Values in brackets should be avoided as far as possible. a Preferred numbers according to series R 20; intermediate values according to series R 40, may be chosen. b The permissible secondary current I X , at a given duty factor X, may be

29、calculated from 2 100 X ll X llllll p The figures in this table are based on a temperature rise of 60 C and terminals connected to water-cooled lugs. 4 Designation The designation of a secondary connecting cable shall consist, in order, of the words “secondary connecting cable”, the number of this I

30、nternational Standard, the cross-sectional area of the cable in square millimetres, the length in millimetres and the type of flexibility. EXAMPLE Designation of a secondary connecting cable with cross-section of 400 mm 2 , a length of 500 mm, flexible type (F): Secondary connecting cable ISO 5828 -

31、 400 500 - FThis standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 5828:2001(E) ISO 2001 All rights reserved 3 5 Materials The materials used shall meet the following requirements: Chemical composition: Cu ( Ag) min. 99,9 % Average density: 8,9 kg

32、/dm 3 Maximum mass resistivity: 0,153 28 . g/m 2 (at 20 o C) NOTE Equivalent values for guidance: Maximum volume resistivity: 0,0172 41 . mm 2 /m Minimum conductivity: 100 % IACS or 58,00 m/ . mm 2 The external insulating cover protecting the connecting cable shall be resistant to common industrial

33、chemical agents and possible spatter, and shall also withstand, without deterioration, a maximum termperature of 100 C. The cable assembly shall not contain silicone. 6 Construction Low flexibility = LF, diameter of wire 0,16 tou 0,25 mm Flexible = F, diameter of wire 0,08 tou 0,16 mm Highly flexibl

34、e = HF, diameter of wireu 0,08 mm Twist of cable 1/2 revolution minimum on length L. 7 Endurance test (type test) 7.1 Test conditions For double series spot welding the secondary connecting cables shall be connected to the cooled secondary terminals of the transformer and to the cooled electrode hol

35、ders, in accordance with the assembly diagram and dimensions indicated in Figure 2, the centre of the connecting cables being unsupported. Rate of 20 strokes/min at 4 % duty cycle for a minimum duration of 8 h without interruption. The applicable welding current shall be calculated from the figures

36、given in Table 1. Under this condition the connecting cable shall withstand 300 000 mechanical and electrical operations. 7.2 Interpretation of results At the beginning and at the end of the endurance test, a precise measurement of the resistance shall be carried out at a temperature of 20 C. The final resistance shall not exceed the initial resistance by more than 15 %.This standard may only be used and printed by approved subscription and freemailing clients of the SABS.