SANS 61326-2-3-2009 Electrical equipment for measurement control and laboratory use - EMC requirements Part 2-3 Particular requirements - Test configuration operational conditions in.pdf

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23148-4 SANS 61326-2-3:2009Edition 1 IEC 61326-2-3:2006Edition 1SOUTH AFRICAN NATIONAL STANDARD Electrical equipment for measurement, cont

4、rol and laboratory use EMC requirements Part 2-3: Particular requirements Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning This national standard is the identical implementation of IEC 61326-2-3:2006, and is adopted wit

5、h the permission of the International Electrotechnical Commission. WARNING Can only be used in conjunction with SANS 61326-1. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 61326-2-3:2

6、009 Edition 1 IEC 61326-2-3:2006 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS TC 73, Electromagnetic compatibility, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of th

7、e WTO/TBT agreement. This SANS document was published in October 2009. NORME INTERNATIONALECEIIECINTERNATIONAL STANDARD 61326-2-3Premire ditionFirst edition2006-07Matriel lectrique de mesure, de commande et de laboratoire Exigences relatives la CEM Partie 2-3: Exigences particulires Configurations d

8、essai, conditions de fonctionnement et critres daptitude la fonction des transducteurs avec un systme de conditionnement du signal intgr ou distance Electrical equipment for measurement, control and laboratory use EMC requirements Part 2-3: Particular requirements Test configuration, operational con

9、ditions and performance criteria for transducers with integrated or remote signal conditioning Pour prix, voir catalogue en vigueur For price, see current catalogue IEC 2006 Droits de reproduction rservs Copyright - all rights reserved Aucune partie de cette publication ne peut tre reproduite ni uti

10、lise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lditeur. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microf

11、ilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch CODE PRIX PRICE CODE U Commission Electrotechnique

12、InternationaleInternational Electrotechnical Commission SANS 61326-2-3:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .61326-2-3 IEC:2006 3 CONTENTS FOREWORD.7 1 Scope.11 2 Normative references .15 3 Terms and definitions .15 4 General 17

13、 5 EMC test plan.17 5.1 General .17 5.2 Configuration of EUT during testing.17 5.3 Operation conditions of EUT during testing17 5.4 Specification of performance criteria .17 5.5 Test description.19 6 Immunity requirements .19 6.1 Conditions during the tests19 6.2 Immunity test requirements .19 6.3 R

14、andom aspects .21 6.4 Performance criteria21 7 Emission requirements .23 7.1 Conditions during measurements 23 7.2 Emission limits 23 8 Test results and test report.23 Annex AA (normative) Additional requirements and exceptions for specific types of transducers Transducers for measurement of tension

15、 and compressive forces (force transducers) .25 Annex BB (normative) Additional requirements and exceptions for specific types of transducers Transducers for measurement of pressure (pressure transducers) 35 Annex CC (normative) Additional requirements and exceptions for specific types of transducer

16、s Transducers for measurement of temperature (temperature transducer)43 Figure 101 Example of a transducer with integrated signal conditioning.13 Figure 102 Example of a transducer with remote signal conditioning13 Figure AA.1 Example of the configuration of a force transducer with remote measured-v

17、alue processing 27 Figure AA.2 Additional maximum measuring error (fz) versus the maximum measuring error (fy) for continuous disturbances 31 Figure AA.3 Additional maximum measuring error (fz) versus the maximum measuring error (fy) for transient disturbances33 Figure BB.1 Example of the configurat

18、ion of a pressure transducer .37 Figure BB.2 Additional maximum measuring error (fz) versus the maximum measuring error (fy) 41 SANS 61326-2-3:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .61326-2-3 IEC:2006 5 Figure CC.1 Example of the

19、 configuration of a temperature transducer with sensor and processing unit in the same housing 45 Figure CC.2 Example of the configuration of a temperature transducer with remote measured-value processing 45 Figure CC.3 Additional maximum measuring error (fz) versus the maximum measuring error relat

20、ed to the measurement span (fy) a) for continuous disturbances (Table CC.2) b) for transient disturbances (Table 10.3)51 Table 101 Performance criteria for the different functions 21 Table AA.1 Circuitry actions for generating an output signal for simulation of a mechanical load on the transducer27

21、Table AA.2 Performance criteria for the different functions.29 Table AA.3 Additional maximum measuring error (fz) for a given maximum measuring error (fy) for continuous disturbances 29 Table AA.4 Additional maximum measuring error (fz) for a given maximum measuring error (fy) for transient disturba

22、nces31 Table BB.1 Performance criteria for the different functions.39 Table BB.2 Additional maximum measuring error (fz) for a given maximum measuring error (fy) 39 Table CC.1 Performance criteria for the different functions 49 Table CC.2 Additional maximum measuring error (fz) for a given maximum m

23、easuring error (fy) for continuous disturbances.49 Table CC.3 Additional maximum measuring error (fz) for a given maximum measuring error (fy) for transient disturbances 49 SANS 61326-2-3:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .61

24、326-2-3 IEC:2006 7 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE EMC REQUIREMENTS Part 2-3: Particular requirements Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal cond

25、itioning FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardizati

26、on in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is en

27、trusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the Inte

28、rnational Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since

29、 each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content o

30、f IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in

31、 their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment de

32、clared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC Natio

33、nal Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is

34、 drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall

35、 not be held responsible for identifying any or all such patent rights. This International Standard IEC 61326-2-3 has been prepared by subcommittee 65A: System aspects, of IEC technical committee 65: Industrial-process measurement and control. The IEC 61326 series cancels and replaces IEC 61326:2002

36、 and constitutes a technical revision. SANS 61326-2-3:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .61326-2-3 IEC:2006 9 The text of this standard is based on the following documents: FDIS Report on voting 65A/477/FDIS 65A/484/RVDFull i

37、nformation on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part of IEC 61326 is to be used in conjunction with IEC 61326-1 and follows the same

38、 numbering of clauses, subclauses, tables and figures as that standard. When a particular subclause of Part 1 is not mentioned in this part, that subclause applies as far as is reasonable. When this standard states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be ada

39、pted accordingly. NOTE The following numbering system is used: subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1; unless notes are in a new subclause or involve notes in part 1, they are numbered starting from 101 including those in a replaced claus

40、e or subclause; additional annexes are lettered AA, BB, etc. A list of all parts of the IEC 61326 series, under the general title Electrical equipment for measurement, control and laboratory use, control and laboratory use EMC requirements can be found on the IEC website. The committee has decided t

41、hat the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or am

42、ended. SANS 61326-2-3:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .61326-2-3 IEC:2006 11 ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE EMC REQUIREMENTS Part 2-3: Particular requirements Test configuration, operationa

43、l conditions and performance criteria for transducers with integrated or remote signal conditioning 1 Scope In addition to the requirements of IEC 61326-1, this part of IEC 61326 specifies more detailed test configurations, operational conditions and performance criteria for transducers with integra

44、ted or remote signal conditioning. This standard applies only to transducers characterized by their ability to transform, with the aid of an auxiliary energy source, a non-electric quantity to a process-relevant electrical signal, and to output the signal at one or more ports. This standard includes

45、 transducers for electrochemical and biological measured quantities. The transducers covered by this standard may be powered by a.c. or d.c. voltage and/or by battery or with internal power supply. Transducers referred to by this standard comprise at least the following items (see Figures 101 and 10

46、2): one or more elements for transforming a non-electrical input quantity to an electrical quantity; a transmission link for transferral of the electrical quantity to a component for signal conditioning; a unit for signal conditioning that converts the electrical quantity to a process-relevant elect

47、rical signal; an enclosure for enclosing the above-stated components fully or in parts. Transducers referred to by this standard may also have the following items (see Figures 101 and 102): a communication and control unit; a display unit; control elements such as keys, buttons, switches, etc.; tran

48、sducer output signals (for example, switch outputs, alarm outputs) which are clearly assigned to the input signal(s); transducers with signal conditioning which may be integrated or remote. The manufacturer specifies the environment for which the product is intended to be used and utilizes the corre

49、sponding test levels of IEC 61326-1. Additional requirements and exceptions for specific types of transducers are given in the annexes to this standard. SANS 61326-2-3:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .61326-2-3 IEC:2006 13 123456789IEC 559/02Key 1 Non-electrical quantity 2 Electrical q