ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:105.45KB ,
资源ID:1046611      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-1046611.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(SMPTE ST 177-1995 Motion-Picture Film (35-mm) - Four-Track Magnetic Audio Release Prints - Magnetic Striping.pdf)为本站会员(diecharacter305)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

SMPTE ST 177-1995 Motion-Picture Film (35-mm) - Four-Track Magnetic Audio Release Prints - Magnetic Striping.pdf

1、SMPTE 177 75 8357403 0002042 806 SMPTE STANDARD for Motion-Picture Film (35-mm) - Four-Track Magnetic Audio Release Prints - Magnetic Striping ANSVSMPTE 177-1 995 Revision aof ANSIISMPTE 177-1990 1 Scope This standard specifies the location and dimensions of the magnetic recording stripes on 35-mm m

2、otion- picture film used for four-track magnetic audio release prints having an anamorphic-type picture image. 2 Normative reference The following standard contains provisions which, through reference in this text, constitute provisions of this standard. At the time of publication, the edition indic

3、ated was valid. All standards are subject to revi- sion, and parties to agreements based on this stand- ard are encouraged to investigate the possibility of applying the most recent edition of the standard indi- cated below. Page 1 of 3 pages ANSIISMPTE 102-1 991, Motion-Picture Film (35- mm) - Perf

4、orated CS-I 870 3 Dimensions 3.1 The location and dimensions of the record- ing stripes shall be as specified in figure 1 and table 1. 3.2 The magnetic stripes shall be on the side of the film which is away from the light source when used on a projector arranged for direct front projection on a refl

5、ection-type screen. 4 Film stock The film stock used shall be safety type, cut and perforated in accordance with ANSIISMPTE 102. CAUTION NOTICE This Standard may be revised or withdrawn at any time. The procedures of the Standard Developer require that action be taken to reaffirm, revise, or withdra

6、w this standard no later than five years from the date of publication. Purchasers of standards may receive current information on all standards by calling or writing the Standard Developer Printed in USA Copynght Q 1995 by THE SOCIETY OF -L American Nalional Standard MOTION PICTURE AND TELEVISION EN

7、GINEERS (914)761-1100 595 W Hartsdaie Ave., White Plains, NY 10607 Approved September 12,1995 SMPTE 177 95 m 357403 o002043 742 m ANSVCMWE 177-1995 TRAVEL ! RE AS SEEN FROM INSIDE PROJECTOR LAMPHOUSE LOOKING TOWARD THE LENS Figure 1 - Location of recording stripes Table 1 - Dimensions 1 Dimensions i

8、nches Mili Imeters A 0.072 f 0.003 B 0.008 max C 0.1 79 f 0.003 D 0.242 f 0.003 E 1.1 69 f 0.003 F 1.207 f 0.003 G 1.306 f 0.003 H 1.369 min 1.83 f 0.08 0.20 rnax 4.55 f 0.08 6.15 f 0.08 29.69 f 0.08 30.66 f 0.08 33.17 f 0.08 34.77 min NCE Page 2 at 3 pages SMPTE 177 95 A357401 0002044 689 ANSVCMPTE

9、 177-1995 Annex A (informative) Additional data A.l The use of polyester base film stock is recommended in order to maintain the specified dimensions. A.2 The dimensions specified in this standard are predi- cated on the use of unshrunk film. It is recognized, however, that some shrinkage may occur

10、when striping a processed print. Specific measurements should take into account the overall width of the film as specified by dimension A in ANSI/SMPTE 102. Should the film width fall outside the permissible tolerance, all dimensions specified in this stand- ard may be multiplied by the ratio of nom

11、inal dimensions determined as follows: Measured width= Ratio of nominal dimensions Specified width A.3 The outer edge of the magnetic striping ideally should be coincident with the edge of the film, and for this reason, dimension B is specified as maximum and dimension H as minimum. A.4 Prints confo

12、r-ing to this standard are prepared in accordance with ANSIISMPTE 194 and ANSIISMPTE 137. Annex B (informative) Bibliography ANSWSMPTE 137-1 994, Motion-Picture Film (35-mm) - Release Prints - Four Magnetic Audio Records ANSIISMPTE 194-1 991, Motion-Picture Film (35-mm) - Projector Usage - Release Prints Having Four Perforations Per Frame Page 3 of 3 pages

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1