ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:51.15KB ,
资源ID:1047074      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-1047074.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(SMPTE ST 7-2004 Motion-Picture Film (16-mm) - Camera Aperture Image and Usage.pdf)为本站会员(Iclinic170)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

SMPTE ST 7-2004 Motion-Picture Film (16-mm) - Camera Aperture Image and Usage.pdf

1、 1 Scope 1.1 This standard specifies the dimensions of the camera aperture image and its relative position to the reference edge and the perforations of 16-mm motion-picture film. The location of the perforations is based on dimensions given in SMPTE 109. 1.2 This standard also specifies the positio

2、n of the emulsion and the frame rate for 16-mm motion-picture film perforated one or two edges. 2 Film position Except for special processes, the emulsion shall be toward the camera lens. 3 Dimensions 3.1 The dimensions shall be as given in figure 1 and table 1 and shall apply to measurements of the

3、 aperture image as formed on freshly exposed and processed film. 3.2 The angle between the vertical and horizontal edges of the aperture image shall be 90 to each other. 4 Frame rate 4.1 The standard frame rate for motion-picture photography is 24 frames per second. However, it is recognized that no

4、nstandard frame rates are sometimes used for specific applications. For example: 24, 25, or 30 frames per second may be used for motion pictures intended for television; higher or lower frame rates may be used for special effects and analysis; and nonstandard rates may be used for special motion-pic

5、ture systems. The use of nonstandard frame rates requires notification and agreement of all parties concerned with the use of the particular film. NOTES 1 Dimension B, vertical height of aperture, must be maintained in order to ensure a real (unexposed) frameline in the projector. Close control of t

6、he tolerances given for dimension B is necessary to enable dimensions F and H to be held within satisfactory limits. These are the distances from the lower edge of the perforation to the horizontal edges of the framelines. Dimensions F and H represent the maximum conditions which can be tolerated du

7、e to misalignment of the horizontal centerline of the aperture opening and the optical centerline of the photographic lens. Dimensions B, F, G, and H shall be measured to lines that are at right angles to the reference edge of the film and through a point where the radius (dimension R) is tangent to

8、 the horizontal framelines (see figure 1). 2 The centerlines of the aperture image are normally on the optical center of the camera. The optical axis of the camera is defined as the mechanical axis or centerline of the sleeve or other device for holding the camera lens. Except for manufacturing tole

9、rances, it coincides with the optical axis of the lens. Page 1 of 3 pagesSMPTE 7-2004 Revision of SMPTE 7-1999 Copyright 2004 by THE SOCIETY OF MOTION PICTURE AND TELEVISION ENGINEERS 595 W. Hartsdale Ave., White Plains, NY 10607 (914) 761-1100 Approved November 8, 2004 SMPTE STANDARD for Motion-Pic

10、ture Film (16-mm) Camera Aperture Image and Usage SMPTE 7-2004 Page 2 of 3 pages 3 Dimension J shows the limits by which the frameline may be out of square with the reference edge of the film, but, at all times, this should be confined within the area designated by dimension G. Figure 1 Camera apert

11、ure image Table 1 Specifications Dimensions1Inches Millimeters A 0.404 nom 10.26 nom B 0.295 + 0.004 0.003 7.49 + 0.10 0.07 D 0.116 max 2.95 max E 0.512 min 13.00 min F 0.018 min 0.46 min G 0.001 0.008 min max 0.03 0.20 min max H 0.032 max 0.81 max J 1/2 1/2 R 0.015 max 0.38 max 1See notes. SMPTE 7-

12、2004 Page 3 of 3 pages Annex A (informative) Additional data A.1 If the aperture plate is not in the plane of the emulsion, the physical dimensions of the aperture in the camera will be slightly different from the dimensions given in figure 1. The exact amount of this difference will depend upon the

13、 f-number and focal length of the camera lenses used and upon the distance between the emulsion and the physical aperture. This separation should be no greater than is necessary to prevent scratching of the film. A.2 It is the intent of this standard to provide a camera image such that the exposed a

14、rea will always be larger than the area of the projector aperture. This standard meets this objective without causing double exposure of the area between frames. A.3 Dimension G, the distance between adjacent framelines, has been limited carefully so as to make it possible to keep both framelines ma

15、sked simultaneously by the projector aperture. In addition, dimensions F and H have been established to limit the distance that any part of the frameline can depart from the bottom edge of the perforations. This is to minimize the necessity for frequent adjustment of the framing device on the projec

16、tor. A.4 The pull-down claw is located at the plus-3 perforation (see figure 1) with respect to the projector or camera aperture. The reason for selecting the plus-3 perforation for positioning is to obtain the positioning perforation as close as possible to the image being photographed, yet not so close as to interfere with the optical system and gate structure. Annex B (informative) Bibliography SMPTE 109-2003, Motion-Picture Film (16-mm) Perforated 1R and 2R

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1