SSPC PS 10 02-1982 Cold-Applied Coal Tar Mastic Painting System《冷用煤焦油胶粘涂料系统 编辑修订 2004年11月1日》.pdf

1、5-51SSPC-PS 10.02November 1, 1982Editorial Revisions November 1, 2004SSPC: The Society for Protective CoatingsPAINTING SYSTEM NO. 10.02Cold-Applied Coal Tar Mastic Painting System1. Scope1.1 This specifi cation covers a cold-applied coal tar paint-ing system for underground and underwater steel stru

2、ctures, consisting of two cold-applied coats.1.2 This system is suitable for use on parts or structures exposed in Environmental Zones 2C (fresh water immersion), 3B (chemical, neutral), and 3C (chemical, alkaline). It has fairly good abrasion resistance and is suitable for underground use. It must

3、be used with discretion for immersion in corrosive chemicals since the coating is dissolved by some organic solvents and attacked by oxidizing solutions.1.3 The coal tar mastic must be topcoated with coal tar emulsion when exposed to sunlight to prevent checking and alligatoring.2. Description2.1 Th

4、is painting system consists of surface preparation by commercial blast cleaning or pickling and two coats of cold-applied coal tar mastic. This paint is self-priming and does not require a separate prime coat. A fi nal topcoat of coal tar emulsion is to be applied when exposed to sunlight. This syst

5、em is not recommended for potable water or high temperatures.3. Referenced Standards3.1 The latest issue, revision, or amendment of the referenced standards in effect on the date of invitation to bid shall govern, unless otherwise specifi ed.3.2 If there is a confl ict between the requirements of an

6、y of the cited referenced standards and this specifi cation, the requirements of this specifi cation shall prevail.3.3 SSPC STANDARDS AND JOINT STANDARDS:PA 1 Shop, Field, and Maintenance Painting of SteelPA 2 Measurement of Dry Coating Thickness With Magnetic GagesPA Guide 4 Guide to Maintenance Re

7、painting with Oil Base or Alkyd Painting SystemsPaint 12 Cold Applied Asphalt Mastic (Extra Thick Film) WithdrawnPaint 32 Coal Tar Emulsion CoatingSP 5/NACE No. 1 White Metal Blast CleaningSP 6/NACE No. 3 Commercial Blast CleaningSP 8 PicklingSP 10/NACE No. 2 Near-White Blast Cleaning3.4 AMERICAN S

8、OCIETY FOR TESTING AND MATERIALS (ASTM) STANDARDS:D 3925 Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings3.5 FEDERAL STANDARDS AND SPECIFICATIONS:MIL-C-15203 Coating Compound, Bituminous, Emulsion Type, Coal Tar Base Canceled. See SSPC- Paint 32.MIL-C-18480 Coating Compoun

9、d, Bituminous, Solvent, Coal Tar Base4. Surface Preparation4.1 SSPC-SP 6, “Commercial Blast Cleaning,” or SSPC-SP 8, “Pickling.” If specifi ed in the procurement documents better degrees of cleaning shall be substituted (SSPC-SP 5, “White Metal Blast Cleaning,” or SSPC-SP 10, “Near-White Blast Clean

10、ing”).5. Paints5.1 PRIMER: MIL-C-18480, “Coating Compound, Bitumi-nous, Solvent, Coal Tar Base.”5.2 SECOND COAT: The second coat shall be the same coating as the fi rst coat.5.3 THIRD COAT (when required): All surfaces that are to be exposed to sunlight shall be given a third coat consisting of MIL-

11、C-15203, “Coating Compound, Bituminous, Emulsion Type, Coal Tar Base.” This coat shall be applied no sooner than two weeks after the second coat is applied.6. Paint Application6.1 PAINT APPLICATION: Follow the requirements of SSPC-PA 1, “Shop, Field, and Maintenance Painting of Steel.”5-52SSPC-PS 10

12、02November 1, 1982Editorial Revisions November 1, 20046.2 TOUCH-UP PAINTING: In accordance with specifi ca-tions SSPC-PA 1, “Shop, Field, and Maintenance Painting of Steel,” and in particular with the section thereof entitled “Field Painting.”6.3 MAINTENANCE PAINTING: This specifi cation ap-plies t

13、o maintenance painting, provided specifi c instructions are included on the degree and amount of solvent cleaning, spot cleaning, spot priming, priming, and fi nish painting. For additional information on maintenance painting procedures, see SSPC-PA Guide 4, “Guide to Maintenance Repainting with Oil

14、 Base or Alkyd Painting Systems.”6.4 NUMBER OF COATS: Minimum of two.6.5 DRY FILM THICKNESS OF PAINT SYSTEM: Not less than the following as measured in accordance with SSPC-PA 2, “Measurement of Dry Coating Thickness with Magnetic Gages”: primer 380 micrometers (15 mils); second coat 250 micrometers

15、 (10 mils); for the two-coat painting system 635 micrometers (25 mils); third coat (when required) 250 microm-eters (10 mils); for the three-coat system 890 micrometers (35 mils).7. Inspection7.1 All work and materials supplied under this specifi ca-tion are subject to timely inspection by the purch

16、aser or his authorized representative. The contractor shall correct such work or replace such material as is found defective under this specifi cation (See Note 9.1.). In case of dispute, unless otherwise specifi ed, the arbitration or settlement procedure established in the procurement documents sh

17、all be followed. If no arbitration or settlement procedure is established, then a procedure mutually agreeable to purchaser, material supplier, and contractor shall be used. 7.2 Samples of paints under this painting system may be requested by the purchaser and shall be supplied upon request along wi

18、th the manufacturers name and identifi cation for the materials. Samples may be requested at the time the purchase order is placed, or may be taken from unopened containers at the job site.7.3 Unless otherwise specifi ed, the sampling shall be in accordance with ASTM D 3925.8. Disclaimer8.1 While ev

19、ery precaution is taken to ensure that all information furnished in SSPC standards and specifi cations is as accurate, complete, and useful as possible, SSPC cannot assume responsibility nor incur any obligation resulting from the use of any materials, coatings, or methods specifi ed herein, or of t

20、he specifi cation or standard itself.8.2 This specifi cation does not attempt to address problems concerning safety associated with its use. The user of this specifi cation, as well as the user of all products or practices described herein, is responsible for instituting appropriate health and safet

21、y practices and for insuring compliance with all governmental regulations.9. NoteNotes are not a requirement of this specifi cation. 9.1 The procurement documents should establish the responsibility for samples, testing, and any required affi davit certifying full compliance with the specifi cation.9.2 If an electrical inspection is required, use a holiday detector of the Tinker-Raser, Bird Dog, or other approved type having a range of 67.5 to 75 volts.