TIA EIA IS-788-1999 Connector Specification for the Portable Phone Vehicle Interface《适用于便携式电话车辆接口的连接器规范》.pdf

1、TIA/EIA INTERIM STANDARD Connector Specification for the Portable Phone Vehicle Interface TIA/EIA/IS-788 JUNE 1999 TELECOMMUNICATIONS INDUSTRY ASSOCIATION NOTICE TIAEIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manu

2、facturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or no

3、nmember of TIA/EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than TIAEIA members, whether the standard is to be used either domestically or internati

4、onally. Standards and Publications are adopted by TIA/EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIAIEIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publi

5、cation. TIA/EIA INTERIM STANDARDS TIA/EIA Interim Standards contain information deemed to be of technical value to the industry, and are published at the request of the originating Committee without necessarily following the rigorous public review and resolution of comments which is a procedural par

6、t of the development of a TIAEIA Standard. TIA/EIA Interim Standards should be reviewed on an annual basis by the formulating Committee and a decision made on whether to proceed to develop a TIA/EIA Standard on this subject. TIAEIA Interim Standards must be cancelled by the Committee and removed fro

7、m the TiA/EIA Standards Catalog before the end of their third year of existence. Publication of this TIA/EIA Interim Standard for trial use and comment has been approved by the Telecommunications Industry Association. Distribution of this TIA/EIA Interim-Standard for comment shall not continue beyon

8、d 36 months from the date of publication. It is expected that following this 36 month period, this TIA/EIA Interim Standard, revised as necessary, will be submitted to the American National Standards Institute for approval as an American National Standard. Suggestions for revision should be directed

9、 to: Standards Connector Mechanical Specifications, and Connector Electrical Specifications. The connector described in this document is intended to make the connection between the vehicle system and the mobile phone system, as described in ref. /Il. 2.1 Description of connector systems The two subs

10、ystems are described in the following sections. Additional system information is available. See I11 for more detail. 2.1.1 Vehicle Systems (AAS) 0 The vehicle sub-system (AAS, Automobile Adaptation System) contains the AAS half of the standard connector mounted on or in the vehicle interior and is a

11、vailable to the occupant for connection to the portable phone. The functions provided by the AAS are described in ref. Ill. 2.1.2 Phone Systems (PAS) 0 The phone subsystem (PAS, Phone Adaptation System) is provided by the portable phone manufacturer (phone adapter module) and contains the PAS half o

12、f the standard connector. The functions provided by the PAS are described in ref. Ill. 1 TIA/EZA/IS-7 88 3. Mechanical Requirements The connector described in this document is one designed specifically for this application. Design requirements from the telecommunications industry and automotive indu

13、stry were taken into consideration in development. 3.1 Connector Overview The connector shall meet the following requirements: 0 0 0 0 0 0 The basic connector is illustrated in Figure 1. Be made to meet the intent of the USCAR, class 1 specifications. See /2/ for more information. Provide cavities f

14、or 12 mated pairs of contacts of the 0.64mm sq. (0.025in sq.) blade and box style. Contact positions 1 through 8 shall be loaded. The use of contact positions 9 through 12 is described in ref. /V. Provide a cavity position for a mated pair of size 8 coaxial pin and socket contacts. See /1/ and /3/ f

15、or more information. Provide for positive latching of connector to prevent accidental disengagement. Maintain mechanical and electrical performance specified in this document for a minimum of 1000 mating cycles. For mating cycles greater than 1000, an optional and replaceable wear adapter may be use

16、d. Meet the dimensional requirements specified in this document. Phone (PAS) connector Vehicle mounted (AAS) connector Figure 1. Mobile Phone to Vehicle Interface Physical Connector (Typical Application) 2 3.2 AAS Dimensions The AAS connector half shall be mounted in the vekcle. The AAS connector sh

17、all conform to the mating dimensions shown in Figure 2. 3.3 PAS Dimensions The PAS connector will be contained on the phone side. The PAS connector shall conform to the mating dimensions show in Figure 3. 3.4 Mated Connector Sectional Dimensions The sectional dimensions for the mated PAS and AAS con

18、nectors are contained in Figure 4. 3.5 Circuit Identification Numbering The AAS connector shall contain circuit identification numbering. Numbering may be included on the mating face of the connector or the back surface or both. Circuit identification numbering is illustrated for the AAS connector r

19、eceptacle in Figure 5. 3 TIAJELUS-788 All Dimensions in millimeters 1.27 .- TYP. I f- t : 1 DATUM A G D + 0.00 - E + o.oo tolerances. - 0.10 F + 0.20 - Oeoo + o-1o tolerances. - 0.00 Negative tolerances may be greater depending on manufacturers Positive tolerances may be greater depending on manufac

20、turers H f 0.05 . J f 0.10 5.40 E 10.80 D +- 32.50 Figure 2. AAS Connector SCALE: NTS - Table 2. Tolerances applied to dimensions in Figures 2 and 3. 4 TIA/EWIS-788 All dimensions in millimeters I I I DATUMA $ -+ I I 1 1.10 t- I TYP MAX ALL AROUND SHROUD MAY EXIST WITHIN DIMENSIONED BOUNDARIES ALL A

21、ROUND 0.80 TYP MAX - OPTIONAL SHROUD RIBS (2) % .60 TYP 15.75 H L 29.95 H. I SCALE:NTS L 12.70 J pl DATUMB G Figure 3. PAS Connector 5 TIA/EIMS-78 8 All dimensions in millimeters 0 I I l - .A I I I I I I I I I 1 I 1 I I I I II I 4 E 4.50 TokNTACT 6.50 MIN SECTION A-A *COAXIAL PIN TO SOCKET OVERLAP I

22、S 5.00 TO 6.00 MM BLADE LENGTH 4 k 8.50 MAX SECTION B-B Figure 4. Mated Connector Sectional Dimensions 6 TllVEIAAS-78 8 Figure 5. Cavity identification numbering (View looking into AAS Connector) 4. Connector Electrical Requirements This connector shall be in compliance with electrical specification PN-4207. 7