TIA-102 BAAA-B-2017 Project 25 FDMA- Common Air Interface.pdf

1、 TIA-102.BAAA-B (Revision of TIA-102.BAAA-A) June 2017Project 25 FDMA Common Air Interface ANSI/TIA-102.BAAA-B-2017 APPROVED: JUNE 19, 2017 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purc

2、hasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of

3、TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accor

4、dance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems

5、associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. Any use of trademarks in this document are for in

6、formation purposes and do not constitute an endorsement by TIA or this committee of the products or services of the company. (From Project No. ANSI/TIA-PN-102.BAAA-B-R1, formulated under the cognizance of the TIA TR-8 Mobile and Personal Private Radio Standards, TR-8.15 Subcommittee on Common Air In

7、terface). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology and Standards Department 1320 N. Courthouse Road, Suite 200 Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, U

8、SA and Canada (1-877-413-5187) International (303-397-2896) or search online at http:/www.tiaonline.org/standards/catalog/ All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (including po

9、sting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact the TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiaonlin

10、e.org/standards/catalog/info.cfm#copyright or Telecommunications Industry Association Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standa

11、rds development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of

12、 patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validit

13、y of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent

14、that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or public

15、ation of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Procedures for American National Standards) then (i) TIA disclaims any duty or obligation to search o

16、r investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see TIA Procedures for American National Standards Annex C.1.2.3) of Essential Patent(s) and published pending patent applic

17、ations shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Doc

18、ument. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CON

19、TENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARD

20、ING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT,

21、 ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF

22、WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TIA-102.

23、BAAA-B i Foreword (This foreword is not part of this document.) This document has been created in response to a request by the Project 25 Steering Committee as provided for in a Memorandum of Understanding (MOU) dated April 1992 and amended December 1993. The MOU states that the Project 25 Steering

24、Committee shall devise a Common System Standard for digital public safety communications (the Standard) commonly referred to as Project 25 or P25, and that TIA, as agreed to by the membership of the appropriate TIA Engineering Committee, will provide technical assistance in the development of docume

25、ntation for the Standard. If the abbreviation “P25” or the wording “Project 25” appears on the cover sheet of this document when published that indicates the Project 25 Steering Committee has adopted this document as part of the Standard. The appearance of the abbreviation “P25” or the wording “Proj

26、ect 25” on the cover sheet of this document or in the title of any document referenced herein should not be interpreted as limiting the applicability of the information contained in any document to “P25” or “Project 25” implementations exclusively. This document was developed by the TIA TR-8.15 Comm

27、on Air Interface Subcommittee and provides a specification of the FDMA Common Air Interface for TIA-102 Land Mobile Radio systems. This document describes the access method, modulation, data rate, and message formats necessary to ensure a common air interface. The 3rdedition (Revision B) of this doc

28、ument revised TIA-102.BAAA-A to address errata comments and align the content with current TR-8 practices. This document cancels and replaces TIA-102.BAAA-A. There is one annex in this document. Annex A is normative and is considered part of this specification. TIA does not evaluate, test, verify or

29、 investigate the information, accuracy, soundness, or credibility of the contents of the Document. In Publishing the Document, TIA disclaims any undertaking to perform any duty owed to or for anyone. Some aspects of the specifications contained in this document may not have been fully operationally

30、tested; however, a great deal of time and good faith effort has been invested in the preparation of this document to ensure the accuracy of the information it contains. TIA-102.BAAA-B ii Patent Identification The readers attention is called to the possibility that compliance with this document may r

31、equire the use of one or more inventions covered by patent rights. By publication of this document, no position is taken with respect to the validity of those claims or any patent rights in connection therewith. The patent holders so far identified have, we believe, filed statements of willingness t

32、o grant licenses under those rights on reasonable and nondiscriminatory terms and conditions to applicants desiring to obtain such licenses. The following patent holders and patents have been identified in accordance with the TIA intellectual property rights policy: No patents have been identified T

33、IA shall not be responsible for identifying patents for which licenses may be required by this document or for conducting inquiries into the legal validity or scope of those patents that are brought to its attention. TIA-102.BAAA-B iii Table of Contents 1. Introduction . 1 1.1 Scope . 2 1.2 Referenc

34、es . 3 1.2.1 Normative References 3 1.2.2 Informative References 4 1.3 Acronyms and Abbreviations 4 1.4 Definitions . 4 1.5 Conventions . 5 1.5.1 Message Bit Numbering . 5 1.5.2 Block and Packet Formats 5 1.5.3 Symbols 5 2. Description 6 3. Voice Coder . 8 4. Voice Formats . 10 4.1 General Descripti

35、on 10 4.1.1 Notation 11 4.1.2 Reserved Bits and Null Bits 11 4.2 Header Word 12 4.3 Voice Frames . 13 4.3.1 Interleaving Schedule . 14 4.4 Encryption Sync Word 16 4.5 Link Control Word . 16 4.5.1 Terminator Link Control 17 4.6 Low Speed Data Word . 17 4.7 Golay Code Generator Matrices . 18 4.8 Hammi

36、ng Code Generator Matrices . 19 4.9 Reed-Solomon Code Generator Matrices 20 5. Data Packets . 23 5.1 General Description 23 5.2 Header Block Structure 24 5.3 Data Block Structure . 24 5.3.1 Unconfirmed Data Block Structure . 24 5.3.2 Confirmed Data Block Structure . 25 5.3.3 Packet CRC 25 5.4 Confir

37、med Data Packet Formats 25 5.4.1 Confirmed Data Packet Header Format . 25 5.4.2 Confirmed Data Packet Data Block Format 27 5.4.3 Confirmed Data Packet Last Data Block Format 28 5.5 Response Packet Format . 29 5.6 Unconfirmed Data Packet Header Format 31 5.7 Enhanced Addressing Format 33 TIA-102.BAAA

38、-B iv 6. Data Error Correction . 36 6.1 Finite State Machine . 37 6.2 Interleaver . 38 7. Channel Access 39 7.1 General Description 39 7.2 Data Units . 39 7.2.1 Header Data Unit 40 7.2.2 Superframe Data Units . 40 7.2.3 Terminator Data Units . 41 7.2.4 Packet Data Unit . 42 7.3 Frame Sync Word . 43

39、7.4 Status Symbols . 43 7.5 Network Identifier 43 7.5.1 Data Unit ID 44 7.5.2 NID Code 44 8. Modulation . 46 8.1 General Description 46 8.2 Symbols 46 8.3 Nyquist Raised Cosine Filter . 46 8.4 C4FM Modulator . 47 8.4.1 C4FM Deviation 47 8.5 CQPSK Modulator 47 8.6 QPSK Demodulator 49 Annex A Transmit

40、 Bit Order (Normative) . 50 A.1 Conventions 50 A.2 Header Data Unit 52 A.3 Logical Link Data Unit 1 58 A.4 Logical Link Data Unit 2 71 A.5 Simple Terminator Data Unit . 84 A.6 Terminator Data Unit with Link Control . 86 TIA-102.BAAA-B v List of Figures Figure 1 Example RF Subsystem Illustration 1 Fi

41、gure 2 RF Subsystem Reference Model Configuration 1 Figure 3 Example Talk-Around Illustration 2 Figure 4 Talk-Around Reference Configuration . 2 Figure 5 Common Air Interface in a Radio System . 2 Figure 6 Reference Model Diagram 6 Figure 7 Simple Transmitter Diagram . 7 Figure 8 u_0 and u_7 Composi

42、tion . 9 Figure 9 Voice Message Structure 10 Figure 10 Data Units for Voice Messages . 10 Figure 11 Diagram of Header Code Word Construction . 12 Figure 12 Diagram of Voice Code Word Construction 13 Figure 13 Diagram of Encryption Sync Code Word Construction . 16 Figure 14 Link Control Formats . 16

43、Figure 15 Diagram of Link Control Code Word Construction 17 Figure 16 Diagram of Terminator Link Control Code Word . 17 Figure 17 Decomposition of Data Message into Packets 23 Figure 18 Confirmed Data Packet Header Block 26 Figure 19 Confirmed Data Packet Data Block. 27 Figure 20 Confirmed Data Pack

44、et Last Data Block . 29 Figure 21 Response Packet Format . 29 Figure 22 Response Packet Data Block . 31 Figure 23 Unconfirmed Data Packet Header Format 32 Figure 24 Unconfirmed Data Packet Last Data Block . 32 Figure 25 Unconfirmed Enhanced Addressing Packet Header Format . 34 Figure 26 Confirmed En

45、hanced Addressing Packet Header Format 35 Figure 27 Rate Trellis Encoder Overview . 36 Figure 28 Trellis Encoder Block Diagram 37 Figure 29 Data Units for Voice and Data Messages . 40 Figure 30 Header Data Unit 40 Figure 31 Logical Link Data Unit 1 41 Figure 32 Logical Link Data Unit 2 41 Figure 33

46、Simple Terminator Data Unit . 42 Figure 34 Terminator Data Unit with Link Control . 42 Figure 35 Packet Data Unit . 42 Figure 36 C4FM Modulator . 47 Figure 37 CQPSK Modulator 47 Figure 38 QPSK Demodulator 49 TIA-102.BAAA-B vi List of Tables Table 1 Interleaving Schedule for Voice Word . 15 Table 2 G

47、enerator Matrix of (16,8,5) code . 18 Table 3 Golay Generator Matrices . 19 Table 4 Generator Matrices for Hamming Codes . 19 Table 5 Representative Examples . 20 Table 6 Elements in Octal and Exponential Form 20 Table 7 GLCGenerator Matrix for Shortened Reed-Solomon Codes 21 Table 8 GESGenerator Ma

48、trix for Shortened Reed-Solomon Codes 22 Table 9 PHDRGenerator Matrix for Shortened Reed-Solomon Codes 22 Table 10 Response Packet Class, Type, and Status Definitions . 30 Table 11 Trellis Code Word Sizes 36 Table 12 Trellis Encoder State Transition Tables. 37 Table 13 Constellation to Dibit Pair Ma

49、pping . 38 Table 14 Interleave Table 38 Table 15 Frame Sync Word Sequence 43 Table 16 Status Symbol Codes 43 Table 17 Network Identifier Information . 44 Table 18 Data Unit Identifier Values . 44 Table 19 NID Code Generator Matrix . 45 Table 20 Dibit Symbol Mapping to Modulation Phase or Deviation 46 Table 21 CQPSK I and Q Lookup Table 48 TIA-102.BAAA-B vii Revision History Version Date Description Interim Standard 03/23/1995 Initial release of Common Air Interfac