TIA-102 BBAC-1-2013 Project 25 Phase 2 Two-Slot TDMA Media Access Control Layer Description Addendum 1 (Addendum to TIA-102 BBAC).pdf

1、 TIA-102.BBAC-1 (Addendum to TIA-102.BBAC) February 2013Project 25 Phase 2 Two-Slot TDMA Media Access Control Layer Description Addendum 1 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purch

2、asers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of T

3、IA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accord

4、ance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems a

5、ssociated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Project No. TIA-PN-102.BBAC-1, formulated un

6、der the cognizance of the TIA TR-8 Mobile and Personal Private Radio TR-8.12 Subcommittee on Two Slot TDMA). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 1320 N. Courthouse Road Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELEC

7、OMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, USA and Canada (1-877-413-5187) International (303-397-2896) or search online at http:/www.tiaonline.org/standards/catalog/ All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by

8、 the TIA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact the TIA Standards Department or go to the TIA website (www.tiaonline.o

9、rg) for details on how to request permission. Details are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyright or Telecommunications Industry Association Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its prese

10、nt or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by o

11、ne or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with referen

12、ce to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing term

13、s or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published

14、 by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering M

15、anual, 4thedition) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essenti

16、al Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or

17、 monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND A

18、LL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS A

19、ND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTNTS. TIA SHALL NOT BE LIAB

20、LE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WH

21、ETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBL

22、ISHED BY TIA WITHOUT SUCH LIMITATIONS. TIA-102.BBAC-1ii Foreword (This foreword is not part of this addendum.) This addendum is being promulgated by the TR-8.12 (Two-Slot TDMA) subcommittee and its working groups under the sponsorship of the Telecommunications Industry Association. The Phase 2 Trunk

23、ed Two-Slot Time Division Multiple Access (TDMA) Voice Services Standard, which includes definition of the new two-slot TDMA common air interface, was developed by the APIC TDMA Task Group and TIA TR-8.12 to be consistent with the APCO/NASTD/FED Project 25 Statement of Requirements (SoR) adopted by

24、the APCO/NASTD/FED Project 25 Steering Committee. The standard used the SoR dated October 17, 2008 as input guidance to capture the relevant user needs requirements. The two-slot TDMA Media Access Control (MAC) layer protocol specification, which is a component of the Phase 2 TDMA two-slot common ai

25、r interface definition, established a TIA standard supporting the provision of trunked voice services using a two-slot TDMA modulation format within a 12.5 kHz bandwidth physical radio channel. TIA makes no claims as to the applicability of the information contained in this document for any purpose

26、although it is believed that the information will prove to be invaluable to implementers and operators of Phase 2 two-slot TDMA equipment. Some aspects of the information contained in this document may not have been fully operationally tested; however, a great deal of time and good faith effort has

27、been invested in the preparation of this document to ensure the accuracy of the information it contains. While all reasonable efforts have been made to ensure the accuracy of this document, it should be understood that significant work remains to fully develop the standard series and all standard se

28、ries documents will be updated as necessary. TIA-102.BBAC-1 iii TABLE OF CONTENTS LIST OF FIGURES . iv LIST OF TABLES v ADDENDUM INTRODUCTION 1 OBSOLESCENCE 1 DOCUMENT REVISION 1 ADDENDUM CHANGES 2 5.1 SYNCHRONIZATION SEQUENCES 2 5.2 PILOT SEQUENCE . 4 7.2.5 Scrambling 4 7.3.1 Assigned VCH Initial A

29、ccess Procedures (Call Setup) 11 7.3.2 Assigned VCH Maintenance Procedures (Traffic Mode) . 13 7.3.3 Assigned VCH Termination (Call Teardown) 15 7.3.3.2 Message Trunked Termination 16 7.3.4.2 Call Continuation on VCH 17 7.3.5.1.1.2 System Response 18 7.3.5.1.1.3 Requesting Subscriber Unit Actions .

30、19 7.3.5.1.1.4 Voice Channel Transition and Signaling 21 7.3.5.2.1.3 Requesting Subscriber Unit Actions . 23 7.3.5.2.1.4 Voice Channel Transition and Signaling 25 8.3 MAC MESSAGE DETAILS 27 8.3.1.3 Unit to Unit Voice Channel User Message 31 8.3.1.12 Radio Unit Monitor Enhanced Command . 33 8.3.1.21

31、Extended Function Command . 34 8.3.1.34 Radio Unit Monitor Command-OBSOLETE 36 8.3.1.37 Manufacturer Message 37 8.3.1.42 Status Update. 38 TIA-102.BBAC-1iv 8.3.1.43 Message Update 40 8.3.1.44 Radio Unit Monitor Command 42 8.4.2 Offset 44 ANNEX B OSP MCO OPCODE LIST (INFORMATIVE) 46 ANNEX E BURST BIT

32、 LOCATIONS (NORMATIVE) 50 LIST OF FIGURES FIGURE 7-1 INTERNAL LFSR GENERATOR OF SCRAMBLE SEQUENCE . 5 FIGURE 7-2 EXTERNAL LFSR GENERATOR OF SCRAMBLE SEQUENCE 5 FIGURE 7-3 MATRIX TO CONVERT TO INTERNAL LFSR 7 FIGURE 7-4 MATRIX TO ADVANCE EXTERNAL LFSR 243 SHIFT CYCLES . 8 FIGURE 7-5 SCRAMBLING SEQUEN

33、CE OFFSETS . 10 FIGURE 8-15 UNIT TO UNIT VOICE CHANNEL USER MESSAGE ABBREVIATED FORMAT . 31 FIGURE 8-16 UNIT TO UNIT VOICE CHANNEL USER MESSAGE EXTENDED FORMAT 32 FIGURE 8-30 RADIO UNIT MONITOR ENHANCED COMMAND - ABBREVIATED FORMAT 33 FIGURE 8-43 EXTENDED FUNCTION COMMAND EXTENDED FORMAT . 35 FIGURE

34、 8-60 RADIO UNIT MONITOR COMMAND-OBSOLETE . 36 FIGURE 8-63 MANUFACTURER MESSAGE 37 FIGURE 8-68 STATUS UPDATE - ABBREVIATED FORMAT 38 FIGURE 8-69 STATUS UPDATE - EXTENDED FORMAT . 39 FIGURE 8-70 MESSAGE UPDATE- ABBREVIATED FORMAT 40 FIGURE 8-71 MESSAGE UPDATE - EXTENDED FORMAT . 41 FIGURE 8-72 RADIO

35、UNIT MONITOR COMMAND-ABBREVIATED FORMAT 42 FIGURE 8-73 RADIO UNIT MONITOR COMMAND-EXTENDED FORMAT 43 FIGURE 8-74 OFFSET FIELD USAGE . 45 TIA-102.BBAC-1 v LIST OF TABLES TABLE 5-1 SYNCHRONIZATION SEQUENCES . 3 TABLE 8-2 MAC MESSAGE LENGTHS 26 TABLE B- 1: REFERENCE 2 OSP OPCODE SUMMARY 46 TABLE E- 1:

36、INBOUND 4V BURST BIT ALLOCATIONS . 50 TABLE E- 2:INBOUND 4V BURST ESS BIT ALLOCATIONS 54 TABLE E- 3: INBOUND 2V BURST BIT ALLOCATIONS . 56 TABLE E- 4: INBOUND SIGNALING WITH SYNC BURST BIT ALLOCATIONS . 60 TABLE E- 5: OUTBOUND 4V BURST BIT ALLOCATIONS . 64 TABLE E- 6: OUTBOUND 4V BURST ESS BIT ALLOC

37、ATIONS 68 TABLE E- 7: OUTBOUND 2V BURST BIT ALLOCATIONS . 70 TABLE E- 8: OUTBOUND SIGNALING WITH SYNC BURST BIT ALLOCATIONS . 74 TABLE E- 9: OUTBOUND SIGNALING NO SYNC BURST BIT ALLOCATIONS . 78 TIA-102.BBAC-1 1 ADDENDUM INTRODUCTION The pupose of this addendum is to update information and correct e

38、rrata contained in TIA-102.BBAC , “Phase 2 Two-Slot TDMA Media Access Control Layer Description”. OBSOLESCENCE The reference to obsolete is used to indicate specific sections of the document which are no longer current. The term is typically used in this document to indicate that specific voice chan

39、nel messages are no longer supported by the standard and have been replaced with another mechanism. The messages are left in the document as previous implementations may have made assumptions about their use and specifically the corresponding opcode may not be re-used. DOCUMENT REVISION HISTORY Vers

40、ion Date Description 0.0 November 2012 Approved for TIA Publication TIA-102.BBAC-1 2 Addendum changes to TIA-102.BBAC start here. Note that section numbers identified in this addendum directly translate to section numbers in TIA-102.BBAC. 5.1 Synchronization Sequences There are four different synchr

41、onization sequences in the traffic channel signaling. The first is an inbound synchronization sequence that occurs in a MAC information signaling slot (clause 4) that has 22 symbols. The second occurs in an outbound signaling slot and has 21 symbols. The third and fourth kinds of synchronization seq

42、uences are in the outbound ISCH and contains 20 symbols. The sync pattern for the outbound ISCH is also mentioned in 3.3.4. The synchronization sequences are given in this subclause. The synchronization sequences are transmitted in the order from top to bottom; the top symbol is transmitted first an

43、d the bottom symbol is transmitted last. The signed dibit symbols, in order of transmission, for the various synchronization sequences that occur in MAC signaling are shown in Table 5-1. TIA-102.BBAC-1 3 Table 5-1 Synchronization Sequences Symbol/Dibit Name IEMI Sync S-OEMI Sync VCH S-ISCH Sync CCH

44、S-ISCH Sync (Informative) S(21) +3 S(20) +3 -3 S(19) -3 -3 +3 -3 S(18) -3 -3 +3 -3 S(17) +3 -3 +3 -3 S(16) +3 +3 -3 -3 S(15) +3 +3 +3 -3 S(14) -3 +3 +3 +3 S(13) +3 +3 -3 -3 S(12) -3 +3 +3 -3 S(11) -3 -3 +3 -3 S(10) +3 +3 +3 +3 S(9) +3 -3 +3 +3 S(8) +3 +3 -3 +3 S(7) +3 -3 -3 +3 S(6) -3 -3 -3 -3 S(5)

45、+3 +3 +3 +3 S(4) -3 +3 -3 +3 S(3) -3 -3 -3 -3 S(2) -3 -3 -3 +3 S(1) -3 +3 -3 +3 S(0) -3 +3 -3 +3 TIA-102.BBAC-1 4 5.2 Pilot Sequence The pilot sequences are 8 bit fields found in inbound bursts and are composed of two sets of four symbols defined in this document and referenced in R3. The signed dib

46、it symbols for the pilot sequences are defined as follows. P1(3) P1(2) P1(1) P1(0) = +1, 1, +1, 1 P2(3) P2(2) P2(1) P2(0) = 1, +1, 1, +1 The pilot sequence P1 is sent at the beginning of the inbound bursts without sync, which is shown as the left most P in Figure 4-1, Figure 4-2, and Figure 4-3. The

47、 pilot sequence P2 is sent at the end of the inbound burst, including bursts with or without sync, which is shown as the right most P in Figure 4-1, Figure 4-2, Figure 4-3, and Figure 4-6. The first four symbols of the inbound signaling burst with sync shown in Figure 4-6 are characterized as pilot

48、symbols, and in that specific instance the pilot symbols would correspond to the first four symbols of the inbound synchronization sequence given in Table 5-1. 7.2.5 Scrambling Scrambling of specific PDUs on a TDMA channel is used to help reject messages from an interfering P25 TDMA system from bein

49、g interpreted as a valid message to/from the primary system. The inbound and outbound voice bursts (2V and 4V) are always scrambled. The signaling bursts are optionally scrambled. A description of the bits that are scrambled are provided later in this subclause. TIA-102.BBAC-1 5 The information used for the scrambling seed is obtained from the Network Status Broadcast message on the FDMA control channel or the Network Status Broadcast MAC message on the TDMA channel. This scrambling is only performed on the TDMA channel. The specific informati