TIA-455-131-1997 FOTP-131 Measurement of Optical Fiber Ribbon Residual Twist《FOTP-131 光纤带残留扭曲的测量》.pdf

1、 TIA-455-131 August 1997FOTP-131 Measurement of Optical Fiber Ribbon Residual Twist ANSI/TIA-455-131-1997 APPROVED: AUGUST 20, 1997 REAFFIRMED: OCTOBER 6, 2000 REAFFIRMED: MAY 10, 2005 REAFFIRMED: MARCH 22, 2013 NOTICE TIA Engineering Standards and Publications are designed to serve the public inter

2、est through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Pub

3、lications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or

4、 internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Pub

5、lication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limit

6、ations before its use. (From Project No. ANSI/TIA-PN-455.131-RF3, formulated under the cognizance of the TIA TR-42 Telecommunications Cabling Systems, TR-42.12 Subcommittee on Optical Fibers and Cables). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 1320 N.

7、 Courthouse Road Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, USA and Canada (1-877-413-5187) International (303-397-2896) or search online at http:/www.tiaonline.org/standards/cat

8、alog/ All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this

9、document, please contact the TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyright or Telecommunications Industry Association Technology (b) there is no assu

10、rance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intel

11、lectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the hol

12、der thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are in

13、stead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or

14、its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such refer

15、ence consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs po

16、licy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a

17、 claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Docume

18、nt. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY

19、RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERR

20、ED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIA

21、L DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES

22、IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TIA/EIA-455-131iFOTP- 131Measurement of optical fiber ribbon residual twistContentsForeword iii1 Introduction 12 Normative references 23 Apparatus 34 Sampling and sp

23、ecimens 45 Procedure 56 Calculations and interpretation of results 67 Documentation 78 Specification information . 8Annex A Default ribbon residual twist test specifications. 9Annex B Comparison between this FOTP and IEC ITU-T requirements 10Figure 1 - Typical test fixture for ribbon residual twist

24、11Figure 2 - Loading ribbon sample.12Figure 3 - Measuring ribbon residual twist13TIA/EIA-455-131iiThis page left blankTIA/EIA-455-131iiiFOTP - 131Measurement of optical fiber ribbon residual twistForeword(This foreword is informative only and is not part of this Standard.)This document comes from TI

25、A Project No. 3540, and was formulated under thecognizance of TIA FO-6.7, subcommittee on Optical Fiber Cable. (Task Group 6.7.16:Cabled Ribbon Specification)This FOTP is part of the series of test procedures included within RecommendedStandard EIA/TIA-455.There are 2 Annexes, both of them informati

26、ve.Key words: Flatness, RotationTIA/EIA-455-131ivThis page left blankTIA/EIA-455-13111 Introduction1.1 IntentThis procedure provides a method of measuring residual twist in optical fiber ribbons,and highlights critical aspects of this measurement.1.2 ScopeThis measurement is for optical fiber ribbon

27、s.1.3 BackgroundOptical fiber ribbon residual twist is a measure of how much a ribbon rotates, or twists,along a given length. Residual twist can result from the ribbon manufacturing process,or from changes in the dimensions of a ribbon due to heat and humidity aging.Excessive residual twist may hin

28、der the splicing of the ribbon or the placement ofprotective sleeves over spliced sections.1.4 HazardsWarning: Take care when handling small-diameter fiber to prevent it from puncturingthe skin, especially in the eye area. Wear safety glasses when performing this test toprevent potential eye damage.

29、TIA/EIA-455-13122 Normative referencesTest or inspection requirements may include, but are not limited to, the followingreferences:EIA/TIA-455-A , Standard test procedure for fiber optic fibers, cables, transducers,sensors, connecting and terminating devices, and other fiber optic componentsTIA/EIA-

30、455-13133 ApparatusThe following apparatus represents one approach to measuring ribbon residual twist.Equivalent designs may be used.3.1 Test FixtureThe test fixture shall be constructed so as to suspend the ribbon in a true verticalposition, while allowing it to rotate freely. Figure 1 presents one

31、 design for such afixture. Methods shall be provided for measuring the ribbon gauge length and formeasuring the differential angle between the top and bottom of the gauge length. Theangle marks on the measurement face are used to indicate the degree of twist. TheZERO point on the angle protractor sh

32、all be arranged to correspond with the ZEROposition of the top ribbon clamp. The resolution and accuracy of the angle markingsshall be based on the ribbon twist tolerances provided in the Detail Specification. If notolerances are provided, an angle scale with markings every 5 degrees with anaccuracy

33、 of + 1 degree may be used as a default.3.2 Plumb LineA plumb line is used to check the vertical alignment of the fixture. The three adjustablefeet on the fixture are used to make corrections. See figure 1.3.3 Top Ribbon ClampThe ribbon clamp at the top of the fixture shall have a large smooth botto

34、m surfacewhich is normal to the axis of the ribbon, so as to support the ribbon in a true verticalposition. The top ribbon clamp may have guide pins or other devices to facilitatealigning the top of the ribbon to ZERO degrees with respect to the marks on the bottomplate. See figure 2.TIA/EIA-455-131

35、43.4 Bottom Ribbon ClampThe bottom ribbon clamp shall have sufficient weight and shall be balanced so as tohold the ribbon taut and true during preparation of the ribbon section under test. Seefigure 2. The weight of this clamp shall not exceed the weight of the specified ribbonload used during twis

36、t measurement. See annex A.3.5 Weighted PointerThe weighted pointer shall apply a known load to the ribbon, and shall be equippedwith a device which indicates the degree of rotation of the specimen. See figure 2.The pointer shall be balanced to prevent side loading of the ribbon, which will inducetw

37、ist. Refer to annex A for default test parameters.3.6 Calibrated ScaleThe scale will be used to verify the gauge length of the ribbon sample.4 Sampling and specimensRibbon specimens may be taken at any point along the ribbon length. Specimens shallbe chosen randomly for all production parameters. Th

38、e ribbon gauge length shall beprovided in the Detail Specification; the overall specimen length shall be sufficientlylonger than the gauge length, to facilitate attachment of the clamps and test weight.Ribbon specimens shall be preconditioned according to the Detail Specification. Referto annex A fo

39、r default gauge length and preconditioning parameters.TIA/EIA-455-13155 ProcedureTo ensure an accurate residual twist measurement, it is critical that the ribbon be heldin a true vertical position, and that the weighted pointer be balanced to avoid sideloading. Misalignments and off center loads wil

40、l induce ribbon twist.The detailed test methods and specific twist measurement fixtures described belowrepresent one way to measure ribbon residual twist. Equivalent methods may be used.5.1 Verify that the test fixture will hold the ribbon sample in a vertical position.5.1.1 Use a plumb line to chec

41、k the vertical alignment of the test fixture. See figure 1.Verify alignment daily when equipment is in use.5.2 Mount the ribbon sample in the test fixture as shown in figure 2. Note thatalignment of the top ribbon clamp is critical for a true vertical mounting of the ribbon.The ribbon should exit th

42、is clamp normal to the surface of the clamp and the topslotted plate. The bottom clamp is free-hanging and will hold the ribbon taut in thefixture.5.3 With the ribbon threaded through the bottom slot, clamp the weighted pointer onthe ribbon. This pointer must be balanced to prevent side loading of t

43、he ribbon. Thedistance from the top of this pointer clamp to the bottom of the top clamp is the ribbongauge length. See figure 2. Measure the ribbon gauge length, compare it to the DetailSpecification, and adjust the vertical position of the pointer as necessary. Record thefinal ribbon gauge length.

44、5.4 Set the entire ribbon/bottom clamp/pointer assembly to the ZERO position. Thismeans that the ribbon is hanging straight (i.e. any natural twist has been taken out),and the pointer is reading ZERO degrees of twist. Turn the pointer by hand, ifnecessary, to take out any twist inherent in the ribbo

45、n.5.5 Cut the ribbon below the pointer, as shown in figure 2, to release the bottomweight. Allow the ribbon and pointer to rotate freely.TIA/EIA-455-13165.6 When the pointer comes to rest, observe and record the final angle of the pointerwith respect to the initial ZERO position. See figure 3.5.7 Ca

46、lculate the ribbon residual twist as described in clause 6.0, and record thevalue.6 Calculations and interpretation of resultsDivide the final angle (degrees) by the measured ribbon gauge length (cm) todetermine the ribbon residual twist (degrees per cm).Residual Twist = Final Angle .Measured Gauge

47、LengthPrecision: The precision of this method is under consideration and is awaitingevaluation.Bias: The bias of this method has not been established.TIA/EIA-455-13177 Documentation7.1 Report the following information for each test:7.1.1 Date of test7.1.2 Identification of procedure used (FOTP-131)7

48、.1.3 Test sample data:7.1.3.1 Sample identification7.1.3.2 Gauge length of ribbon. (subclause 5.3)7.1.3.3 Final ribbon angle. (subclause 5.6)7.1.3.4 Calculated ribbon residual twist. (clause 6.0)7.1.3.5 Test conditions as applicable (time, temperature, humidity)7.1.4 List the test equipment used and

49、 the last calibration date.7.2 U.S. Military applications require the following information also be reported witheach test:7.2.1 Names of test personnel.TIA/EIA-455-13188 Specification informationThe Detail Specification shall include the following requirements for ribbon residualtwist:8.1 The ribbon gauge length over which twist is to be measured8.2 The test weight clamped to the ribbon8.3 The allowable twist per unit length (degrees per cm)8.4 The preconditioning requirements for the ribbon samples. If any of theseparameters are not specified, those parameters shown in a